Bercomac 700525-2 Bedienungsanleitung
106078 L-03
Instructions
CAB FOR WALK-BEHIND SNOWBLOWERS #700525-2
INSTALLATION
PRE INSTALLATION:
NOTE: Some standard pre assembly has been done (the most commonly used) to facilitate installation. Certain
models of walk behind snowblowers have accessories attached on the handle bar that come into interference
with the cab’s right adjustable support assembly.
Please follow the instructions that are in the hardware bag. Refer to the parts breakdown for identification of the
parts.
Determine the location of the left and right adjustable support assemblies that will adapt the best on your
snowblower. Several possibilities are offered, they are not all illustrated.
About twelve positions are possible and are adjustable in different ways. The link can be inverted which will allow
even more positions.
The right & left adjustable supports can be moved from one side to the other, the inside and outside attaching
plates can be inverted on either the vertical and horizontal handles, which will give a greater quantity of
positions.
The inside and outside attaching plates were designed to accept different sizes of snowblower handles.
Determine the installation that is necessary for your snowblower. Position the carriage bolts as close as possible
to the handles of the snowblower.
106078 L-03
ASSEMBLY
INSTALLATION:
Remove the flange nuts M8 (item 1) and the
carriage bolts M8 x 65mm (item 2) from the right
and left adjustable support assemblies (item 3).
This will allow you to remove the 13mm tools (item
4) that you will use during the rest of the installation.
Place in a satisfactory and temporary position the
right (item 1) and left (item 2) adjustable support
assembly on the handles of the snowblower as
determined previously with the nuts and bolts
previously removed.
Tighten the nuts lightly (item 3).
This will allow you to freely adjust the assembly in the
following steps.
Install the adjustable support assemblies.
Insert the right pipe assembly (item1) and the left pipe
assembly (item 2) in the adjustable support
assemblies (item 3) as shown.
Install the left and right pipe assemblies.
Insert the central pipe (item 1) between the pipe
assemblies (items 2 & 3) as shown.
Make sure the central pipe is well inserted in the snap
in buttons .
Install the central pipe
Install the assembled extensions
Insert the assembled extensions (item 1) in the right
and left pipe assemblies (item 2) up to the pressure
buttons as shown.
Remove the nuts and bolts.
106078 L-03
ASSEMBLY
Place your assembly in the middle of the snowblower.
Position it so that it is parallel with ground in both
directions; front (View A) and the side (View B).
Tighten all the bolts and nuts firmly.
Place the mounting parallel with the ground
Insert the eight vertical rods (item 1) (all the same
length) on the assembly (item 2) as shown.
Insert the eight vertical rods
Install the corners
Insert the corners A, B, C. D, (identified with a letter)
on the vertical rods (item 1).
106078 L-03
ASSEMBLY
Install the two lateral rods (item 1) (the two shortest
ones) in the corners (item 2) as shown.
Install the lateral rods
Install the front and back rods
Install the front & back top rods (item 1) (in the
corners (item 2) as shown.
Install the canvas (item 1) on the cab assembly, make
sure the back panels (item 2) are over the back top
rod.
Hang the canvas and hold in place with the Velcro
straps at the base of the canvas and at the back.
Install the canvas
106078 L-03
ASSEMBLY
You can change the windows panels.
The canvas is preassembled with a removable
window panel (long panel).
If the snowblower is equipped with headlights,
handles or other accessories, remove the long
window panel (item 1) from the window.
You can use the three panels (items 2,3 & 4)
according to your needs.
NOTE: Make sure that you do not block the
engine air-intake and that the emanations do not
enter the cab when the canvas is tied down in
place.
106078 L-03
PARTS BREAKDOWN
CAB FOR WALK BEHIND SNOWBLOWER
106078 L-03
PARTS LIST
CAB FOR WALK BEHIND SNOWBLOWER
Ref.
Réf. English description Description française Qty.
Qté.
Part #
Pièce #
1Central pipe Tube central 1105450
2Left pipe Tube gauche 1105451
3Right pipe Tube droit 1105452
4Extension Extension 2105453
5Bushing Coussinet 2105454
6Lateral rod Tige latérale 2105455
7Top rod Tige du haut 2105456
8Left adjustable support Support ajustable gauche 1105457
9Right adjustable support Support ajustable droit 1105458
10 Base adjustable support Support de la base ajustable 2105459
11 Link Lien 2105460
12 Outside mounting plate Plaque de montage extérieure 2105461
13 Inside mounting plate Plaque de montage intérieure 2105462
14 A corner Coin A 1105463
15 C corner Coin C 1105464
16 B corner Coin B 1105465
17 D corner Coin D 1105466
18 Snap Button Bouton pression 4105467
19 Vertical rod Tige verticale 8105468
20 Key 13 mm Clé 13 mm 2105469
21 Canvas assembly with Berco decal Toile assemblée avec décalque Berco 1105827
22 Shim Cale 2105471
23 Spacer Espaceur 1106080
24 Hex. bolt M8 x 1.25 x 16 Boulon hex. M8 x 1.25 x16 4O/L
25 Hex. bolt M8 X 1.25 X 45 Boulon hex. M8 X 1.25 X 45 2O/L
26 Carriage bolt M8 x 1.25 x 20 Boulon à carrosserie M8 x 1.25 x 20 2O/L
27 Carriage bolt Fully Threaded M8 x 1.25 x 65 Boulon carros. fileté p. long. M8 x 1.25 x 65 4O/L
28 Flange nut M8 x 1.25 Écrou à bride M8 x 1.25 4O/L
29 Nylon insert lock nut M8 x 1.25 Écrou à garniture de nylon M8 x 1.25 6O/L
30 Flat washer M8 Rondelle plate M8 2O/L
31 Reflective Berco decal Décalque Berco réfléchissant 2105369
O/L = Obtain Locally
106078 L-03
WHEN PERFORMANCE
& DEPENDABILITY
ARE NON NEGOTIABLE !
Bercomac Limit ée
92, Fortin Nor th, Adst ock, Quebec, Canada, G0N 1S0
WWW.BERCOMAC.COM
PRINTED IN CANADA
(ORIGINAL NOTICE)
BY
Inhaltsverzeichnis
Andere Bercomac Zubehör für Schneefräsen Handbücher
