Berner AI08 Montage- und Bedienungsanleitung

Thank you for choosing Berner.

Berner International has been saving energy and creating healthy, comfortable environments for our customers

for over 60 years. Berner oers unmatched quality, performance, and dependability—not to mention our service.

At Berner, we stand behind our products.

TABLE OF CONTENTS

I. UNCRATING.................................................................................................................................................................................................................... 2

II. GENERAL MOUNTING INSTRUCTIONS .................................................................................................................................................................... 4

III. WALL MOUNTING ...................................................................................................................................................................................................... 5

IV. SUSPENDED MOUNTING .......................................................................................................................................................................................... 5

V. ELECTRICAL CONNECTIONS ..................................................................................................................................................................................... 5

VI. FIELD CONNECTIONS ................................................................................................................................................................................................ 6

VII. OPERATING INSTRUCTIONS (Intelliswitch™, Berner AIR™, BACnet) ................................................................................................................ 7

INTELLISWITCH™ QUICK START OPERATION.................................................................................................................................................... 10

FAQ’s (FREQUENTLY ASKED QUESTIONS) ......................................................................................................................................................... 12

VIII. MAINTENANCE AND CLEANING............................................................................................................................................................................ 8

IX. SERVICE ....................................................................................................................................................................................................................... 8

X. TROUBLESHOOTING ................................................................................................................................................................................................. 14

XI. APPENDIX

A. SERIAL NETWORK CONNECTION ................................................................................................................................................................... 15

B. WALL MOUNTED TOUCHSCREEN ................................................................................................................................................ .................. 15

C. BACnet-IP INTEGRATION ................................................................................................................................................................................. 15

XII.WARRANTY ............................................................................................................................................................................................................... 16

Installation & Maintenance Instructions

II-280D

June, 2023

©Copyright, 2023 Berner International

READ ALL INSTRUCTIONS BEFORE INSTALLING OR USING AIR CURTAIN

IMPORTANT INSTRUCTIONS

Architectural Icon

Air Curtain Series

#AI08 & AI10

www.Berner.com

WHEN THE DOORS ARE OPEN™save energy & create healthy, comfortable environments

BERNER.COM

Connect with

BERNER AIR

SET UP

CONTROL

TROUBLESHOOT

-2-

Carefully examine the carton(s) for damage. If the carton is damaged,

immediately notify the shipping company. Do not delay in ling a

claim. If the air curtain(s) were shipped on wooden skids, remove

protective wood and banding straps securing the carton(s) to the skid.

Open the carton(s) and remove all protective packaging.

Locate the wall mounting plates. Shorter units will have (3), longer units

may have (6). See Figure 1.

NOTE: if the unit was ordered with a decorative rear cover, the air

curtain will arrive with the cover already installed, and the wall

mounting plates will not be included in the shipment.

Contact Berner, if they are required, for no charge.

Immediately verify that the electrical rating nameplate located on the

cover matches the electrical power supply available. Retain the shipping

carton(s) until the air curtain(s) are installed and properly operating.

ACCESSORIES: If the air curtain(s) were ordered with optional electrical

accessories, the accessories will be found in the carton containing the

air curtain packed in a red bag (marked “additional parts inside”) or in a

separate carton(s) accompanying the air curtain(s).

Check all of the cartons/skids for accessories before discarding.

Figure 1 - Uncrating

A. Read all instructions before installing or using this air curtain.

B. Use this unit only in the manner intended by the manufacturer and described in this manual. Any other use not recommended by the

manufacturer may cause re, electric shock, or injury to persons. If you have any questions, contact the manufacturer.

C. Before servicing or cleaning unit, switch power o at service panel and lock the service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

D. Installation work and electrical wiring must be done by qualied person(s) in accordance with all applicable national and local codes

having jurisdiction, including re-rated construction. See page 5, ELECTRICAL CONNECTIONS (NEC Code ANSI/NFPA No. 70).

E. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

F. To reduce the risk of re, do not store or use gasoline or other ammable vapors and liquids in the vicinity of the air curtain.

G. This air curtain is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture,

pillows, bedding, papers, clothes, etc. and curtains at least 1 inch from the top, back, front, sides and at least 6 feet from the discharge

of the air curtain.

H. Extreme caution is necessary when any air curtain is used by or near children or invalids, and whenever the heater is left operating

unattended.

I. Do not operate any air curtain after it malfunctions. Disconnect power at the service panel and have the air curtain inspected by a

reputable electrician before reusing.

J. To disconnect the air curtain, turn controls to "o", and turn o power to the air curtain circuit at main disconnect panel.

K. Do not insert or allow foreign objects to enter any ventilation or discharge opening as this may cause an electric shock or re, or

damage the air curtain.

L. To prevent a possible re, do not block the air intake or discharge of the air curtain in any manner.

M. The air curtain has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or ammable vapors or liquids

are used or stored.

N. This heater may include an audible or visual alarm to warn that parts of the heater are getting excessively hot. If the alarm sounds

(or illuminates), immediately turn the heater o and inspect for any objects on or adjacent to the heater that may have blocked the airow

or otherwise caused high temperatures to have occurred. DO NOT OPERATE THE HEATER WITH THE ALARM SOUNDING (OR ILLUMINATING).

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

I. UNCRATING

Model: AI08

For mounting

heights up to 8'

Model: AI10

For mounting

heights up to 10'

PACKING

WALL

MOUNTING

BRACKETS

-3-

www.berner.com Berner International 800.245.4455

111 Progress Ave. / New Castle / PA / 16101 / USA

Use threaded rod

to hang from the

ceiling instead of

the wall, using

the factory installed

recessed threaded

inserts

To wire – follow the wiring diagram (inside wiring

compartment). The controls ship in the same box as the

air curtain.

After hanging the wall mounting plates, position the unit

against the wall, slide it down so the top two wall mounting

plates interlock, and install the locking screw.

Before hanging,

check to see what

the clearance is

above the door.

FLUSH WALL MOUNT RAISED WALL MOUNT*

Architectural Icon 8 & 10 Air Curtain

Simple to Install

Easy to operate & maintain

To access internal components,

remove screws along the top

front of the unit that hold the

inlet screen assembly in place.

Rotate it forward to allow the

tabs to come out of their slots

and set the inlet screen assy

aside. Remove the newly

exposed screws along the front

of the unit that hold the BAC in

place. Remove the screws on

the left and right of the BAC and

swing the panel down.

*If the unit must be mounted higher than 1”above the

opening, it must be spaced out from the wall 3/8” for every

inch the unit is above the door opening.

WALL MOUNT WALL MOUNT

For more information see page 4 For more information see page 4

For more information see page 5 For more information see page 5

For more information see page 5 For more information see page 8

CEILING MOUNT

Discharge

Nozzle

4" minimum

side & top

clearance from

combustible

material

20°

AIR

INTERIOR

EXTERIOR

6' minimum

AIR

Airstream

AI08 - 4¾”

AI10 - 91

/8”

AI08 - 9½”MIN.

AI10 - 14”MIN.

WALL

MOUNTING

BRACKETS

1/4” FASTENERS

(by others)

SUPPLIED 1/4-20 BOLTS

TIGHTEN TO 50 IN-LBS

LOCKING

SCREW

LOCKING

SCREW

WIRING

COMPARTMENT

COVER

AI08 - 4¾”

AI10 - 91

/8”

BOTTOM

ACCESS

PANEL SUB

ASSEMBLY

ATTACH

TO WALL

-4-

II. MOUNTING INSTRUCTIONS (General)

INDOOR MOUNTING ONLY -

To achieve optimum protection, the air curtain should be

mounted on the inside of the building, ush to the wall and

as close to the top of the door opening as possible. To ensure

peak performance, keep the air stream free of obstructions.

The air curtain will not perform properly if negative air

pressure exists in the building. Under these conditions,

a means for makeup air to the building must be provided

so that the air pressure on both sides of the opening is in

balance.

Before mounting the air curtain, check the supporting structure

to verify that it has sucient load-carrying capacity to support

the weight of the air curtain(s). The mounting hardware

(supplied by others) should be capable of supporting a

minimum of three (3) times the weight of the air curtain.

See Table 1.

IMPORTANT: A minimum of 4”is required above the top rear

corner of the air curtain for the installation and removal of the

inlet screen, and to ensure proper airow.

A. When determining the mounting location for the air

curtain(s), make sure that nothing interferes with the

curtain of air developed when the discharge vanes

are directed from 0° to 20° toward the door opening. If

the air stream strikes any obstruction (the top edge of the

doorway, a door opening device, etc.), the eectiveness

of the air curtain will be greatly reduced. See Figure 2.

B. For optimum performance, the bottom of the air curtain

(discharge nozzle) should be no more than 1” above

the top of the door opening with the air curtain(s)

mounted ush to the wall. If the air curtain must be

mounted higher, it must be spaced out from the

wall 3/8”for every inch the air curtain is above the door

opening. See Figure 3. For optimum protection, any void

between the air curtain and the wall should be sealed

along the full length of the air curtain.

C. Do not block (obstruct) the air intake screen. Insucient

airow can cause the unit to overheat.

D. The air curtain(s) shall:

1. Have a minimum clearance of at least 4”

from the sides and 4" from the top.

2. Have a minimum clearance of at least 6’

between the bottom of the air curtain and the oor.

3. Be installed Indoors Only.

E. Proceed to either Section III - WALL MOUNTING or

Section IV - SUSPENDED MOUNTING

Figure 2 - General Mounting

Figure 3 - Wall Mounting Location

TABLE 1 - Weight Chart

A. PREPARATION

1. Locate the wall mounting plates, in the carton that

contained the unit. See Figure 4. For units over 72",

there are more than two wall mounting plates.

2. Use ¼"-20 bolts to attach the wall mounting plates

to the back of the air curtain.

III. WALL MOUNTING

20°

AIR

Discharge

Nozzle

INTERIOR

EXTERIOR

6' minimum

AIR

Airstream

4" minimum

side & top

clearance from

combustible

material

MODEL

Net Weight

MODEL

Net Weight

AI10

Amb.

AI10

Elec.

AI10

Steam

AI10

Hot

Water

AI08

Amb.

AI08

Elec.

AI08

Steam

AI08

Hot

Water

AI10-E-1036 85 88 110 107 AI08-E-1036 48 53 68 68

AI10-E-1042 94 97 122 119 AI08-E-1042 53 58 76 75

AI10-E-1048 110 113 141 138 AI08-E-1048 58 63 83 83

AI10-E-1060 119 122 156 153 AI08-E-1060 69 74 99 99

AI10-E-2072 170 176 216 210 AI08-E-1072 79 89 117 117

AI10-E-2084 188 194 240 234 AI08-E-2084 106 116 149 149

AI10-E-2096 220 226 278 272 AI08-E-2096 116 126 164 164

AI10-E-2108 229 235 293 287 AI08-E-2108 127 137 180 180

AI10-E-2120 238 244 306 300 AI08-E-2120 138 148 196 196

AI10-E-3132 305 314 384 375

AI10-E-3144 330 339 415 406

-5-

Figure 6 - Suspended Mounting

Figure 4 - Wall Mounting Preparation

Figure 5 - Wall Mounting Installation

IV. SUSPENDED MOUNTING

NOTE: The three wall mounting plates are identical. Two of the

wall mounting plates are attached to the back of the air curtain,

and one is attached to the wall.

3. The mounting hardware (supplied by others) must

be capable of supporting a minimum of three times

the net weight of the Air Curtain. See Table 1.

B. MOUNTING WALL PLATES

1. Position wall mounting plate over the door opening

as shown in Figure 3. The plate should be centered

over the door opening.

2. Using minimum ¼" fasteners (supplied by others),

secure the wall mounting plate to the supporting

structure. NOTE: It is acceptable to drill holes

through the plate mounted to the wall to

allow fasteners to hit a wall stud. Fasteners must

be placed within 6" of the ends of the air curtain

cabinet.

C. ATTACHING THE AIR CURTAIN TO THE WALL

MOUNTING PLATES

1. Raise the unit over the door (air discharge nozzle

facing down) and onto the wall mounting plates.

See Figure 5.

2. Position the unit against the wall, slide it down so

the top wall mounting plate (attached to the unit)

interlocks with the wall mounting plate that is

attached to the wall. Add one locking screw in the

top middle of the wall mounting plate. See Figure 5.

3. Proceed to Section V - ELECTRICAL CONNECTIONS

V. ELECTRICAL CONNECTIONS

NOTE: if the unit was ordered with a decorative rear

cover, the air curtain will arrive with the cover already

installed, and the wall mounting plates will not be included in

the shipment. Contact Berner if they are required.

A. For top mounting using suspension rods, four (4) factory

installed 1/4"-20 threaded inserts are located on the top of

the unit. See Figure 6.

B. Install 1/4"-20 threaded rods, or other suitable hardware at

a location sucient to support the Air Curtain. The

mounting hardware (supplied by others) must be capable

of supporting a minimum of three times the net weight of

the Air Curtain. See Table 1.

C. Attach 1/4"-20 threaded rods, or other suitable hardware

to the top mounted threaded inserts. Secure threaded rods

with locking nuts.

D. Proceed to Section V – ELECTRICAL CONNECTIONS

All electrical wiring and connections MUST be performed by

qualied personnel in accordance with the latest edition of the

National Electrical Code ANSI/NFPA No. 70 or, in Canada, the

Canadian Electrical Code, Part 1-C.S.A. Standard C22.1 and local

codes and regulations.

MAKE SURE THE CORRECTVOLTAGEAS MARKED

ON THE UNIT IS USED.

LOCKING

SCREW

LOCKING

SCREW

WALL

MOUNTING

BRACKETS

1/4” FASTENERS

(by others)

SUPPLIED 1/4-20 BOLTS

TIGHTEN TO 50 IN-LBS

ATTACH

TO WALL

-6-

A. A separate line voltage supply with a suitable branch

circuit protection device should be run directly from the

main electrical panel to the unit. A disconnect switch for

each branch circuit is a required part of this installation.

See the voltage label on the unit for circuiting and total

electrical load. The wiring diagram is located in the

wiring compartment, located on the top of the unit.

See Figure 7.

B. All eld wiring must be copper with a minimum

insulation of 60°C within approved conduit. If any of the

wire supplied in the unit must be replaced, it must be

replaced with copper wire with a minimum insulation of

90°C.

C. Electric and hot water heated air curtains are factory

equipped with an unit mounted solid state temperature

sensor located internally to measure the incoming

(return) air stream.

D. Remove the wiring compartment cover.

E. Connect all supply and control circuit wires according to

the wiring diagram provided.

NOTE: For Electric and Hot Water heated air curtains

provided with an optional remote thermostat, mount

and wire the thermostat according to thermostat

instructions and wiring diagram.

For BACnet-IP Integration –

see XI - Appendix C, “BACnet-IP integration.”

For Serial Network Connection - proceed to

XI - Appendix A, “Serial/Network Connection.”

NOTE: The air curtain must have been ordered from the

factory with this option.

For Wall Mounted Touchscreen – proceed to

XI - Appendix B,“Wall Mounted Touchscreen.”

if optional remote Touchscreen control of the

Intelliswitch™ has been ordered from the factory.

For Electric and Hot Water air curtains - proceed to

Section VI - Field Connections, otherwise proceed to

Section VII - Operating Instructions

A. ELECTRICALLY HEATED MODELS

The heater circuit may be controlled by an optional

remote thermostat or through the built-in Intelliswitch™

thermostat, which on Model IC08 is located in the wiring

compartment, and on Model IC10 is factory installed

inside the air curtain. Overheating protection is provided

by auto reset thermal cutouts built into the heater coil

assembly (see the wiring diagram located in the wiring

compartment). See Figure 7.

B. STEAM OR HOT WATER HEATED MODELS

An optional water coil solenoid valve (by others or

Berner) may be controlled through the Intelliswitch™ or

independently. The Intelliswitch™ is capable of providing

the same voltage used for the motor to power a solenoid

load up to 5 amps. This call for heat may be controlled

by an optional remote thermostat or through the built-

in Intelliswitch™ thermostat located on top of the air

curtain. Piping should be done in accordance with local

codes, regulations and standard practices. Connect the

building system to the (3/4"-AI08 or 1"- AI10) MPT supply

and return header connections. See Figure 8.

VI. FIELD CONNECTIONS

Figure 7 - Electrical Connections

WIRING

COMPARTMENT

COVER

KNOCKOUTS

FOR POWER &

CONTROL

WIRING

Figure 8 - Steam / Hot Water Connections

-7-

VII. OPERATING INSTRUCTIONS

Figure 9 - Air Stream Adjustment

This air curtain comes with the Berner Intelliswitch™ Digital

Controller built-in to control and schedule fan activation, fan

speed selection, and heat activation. If the optional Berner

AIR™ system (smart controller and app) was ordered, it includes

additional features such as BACnet capability and adaptive

settings. The air curtain must be properly installed before either

of these can be used.

A. GENERAL OPERATION

1. To operate using the built-in Intelliswitch digital

controller, proceed to the Quick Start Operation

Guide, page 10.

NOTE: For a detailed Intelliswitch Programming Guide,

go to www.Berner.com/Intelliswitch

2. Unheated units will have the fans activated by a door

switch or sensor. The unit speed can be selected via the

Intelliswitch™ display or the Berner AIR App*

3. Heated units will have fans activated by a door switch

or sensor, but may also be activated by the thermostat

in Comfort Plus Mode. The unit's speed can be selected

via the Intelliswitch display or the Berner AIR App.*

4. To operate using the Berner AIR™ App*, download the

app and follow the prompts. Requires on-site, secure

wi- connection. Berner recommends having the on-

site user(s) set-up the Berner AIR™ App on his/her smart

phone.

5. To operate using BACnet-IP client, download the Berner

AIR™ App*. In the settings menu of the app, select the

BACnet option. Follow the prompts to congure the

BACnet controller. To connect via wire, see Appendix C.

BACnet-IP Integration.

*NOTE: The air curtain must have been ordered from the factory

with the Berner AIR (smart controller & App) option.

B. AIR STREAM ADJUSTMENT

1. With the air curtain operating and the door in its full

open position, check to see that nothing is obstructing

the airow at the discharge nozzle vanes.

2. Find the air stream split location. Hold a handkerchief

by its corners, approximately 12”above the oor. Gently

move the handkerchief back and forth in the doorway.

Make sure the air is being directed to both the inside

and the outside. See Figure 9. The split location is

indicated where the handkerchief is vertical with

minimal or no uttering.

3. The split location should be approximately 3”outside

the doorway. If necessary adjust the discharge nozzle

vanes by de-energizing the unit and rmly pushing/

pulling on the vane tip until properly located.

BERNER.COM

Connect with

BERNER AIR

SET UP

CONTROL

TROUBLESHOOT

If ordered with the Berner AIR™

20°

AIR

Discharge

Nozzle

INTERIOR

EXTERIOR

6' minimum

Handkerchief

12"

AIR

Airstream

-8-

IX. SERVICE

CAUTION: ELECTRIC SHOCK HAZARD Disconnect power

whenever servicing unit. More than one disconnect may

be required to de-energize unit.

Any service performed on the ARCHITECTURAL Icon Series air

curtain MUST be done by qualied personnel. Berner air curtains

require very little servicing. All parts areeasily accessible for

periodic inspection and maintenance. Units shouldbe cleaned

at least twicea year. Yourparticular application (the amount of

dirt and dust in the air) and location of the unit(s) will determine

how often your unit(s) will need to be cleanedandserviced.All

motorshave permanentlylubricated, sealed, sleeve bearings

and require nomaintenance.

Figure 10 - Bottom Access Cover (BAC) Removal

VIII. MAINTENANCE & CLEANING

CAUTION: ELECTRIC SHOCK HAZARD Disconnect power

whenever servicing unit. More than one disconnect may be

required to de-energize unit.

Stainless steel appliance wipes are recommended for

wiping down both the bottom panel and the cabinet.

Keep your air curtain operating at peak eciency by cleaning

the blower wheels, motor(s) and intake screen. Buildup of dust

onthe blowerwheels cancause vibration,noiseand excessive

wear on the motor bearings. The frequency of cleaning will

Dirty, dusty or greasy environments could require a cleaning

schedule of once every month. If the environment is not that

dirty, the unit(s) should be scheduled for cleaning a minimum

of once every six months. The air inlet lter typically requires

cleaning every three to six months.

A. PERFORMING PREVENTIVE MAINTENANCE

1. Disconnect the power to the unit.

2. Filter - the aluminum washable lter is held in by

the intake screen. Access the lter by removing the

Phillips head ush mount screws across the top front

of the unit. Rotate the inlet screen forward slightly to

allow its tabs to be removed from the bottom front

cover. Vacuum and/or wash with dish soap and water.

3. Internal - open the bottom access panel by removing

the inlet screen as described above, and then

removing the now exposed fasteners across

the front of the BAC, and the two screws along

the bottom left and right side. The BAC is hinged,

so carefully allow it to swing down.Vacuum and scrape

(if necessary) to remove the build-up of dirt

and debris. The motor(s) are permanently lubricated

and require no additional lubrication.

4. Re-install the cover and intake screen. See Figure 10.

5. Switch the power on after cleaning.

CAUTION: STAND CLEAR OF THE UNIT OR WEAR SAFETY

GOGGLES AS LOOSE DEBRIS MAY BE PRESENT AND MAY EXIT

THE NOZZLE UPON START UP!

INLET SCREEN

SUB ASSEMBLY

BOTTOM

ACCESS PANEL

SUB ASSEMBLY

-9-

AI08: To replace fans and/or motors. See Figure 11

1. Lock out power from the unit.

2. Swing down the bottom access cover (BAC) by removing

the ush screws across the front bottom of the unit

3. Disconnect the motor wiring harness.

4. Using a 1/8" hex driver, loosen the set screws (one on each

fan) that secure the fan hubs to the motor shafts.

5. Loosen, but do not remove the screw on each fan bearing

retainer and rotate up to fully expose the fan bearing.

6. Slide each fan in towards the motor as far as possible.

7. While supporting the motor with one hand, remove the

screws at the top of the motor mount. This will free the

motor/fan assembly.

8. Lower the motor/fan assembly out of the unit. Ensure the

rubber bearing cushions come out with the fan bearings.

9. Replace in reverse order. Note that when reinserting the

fan bearings, ensure the rubber bearing cushion is properly

seated. Improper seating can result in fan failure.

AI10: To replace fans and/or motors. See Figure 12

1. Lock out power from the unit.

2. Swing down the bottom access cover (BAC) by removing

the ush screws across the front bottom of the unit.

3. Disconnect the motor wiring harness.

4. If the module has electric heaters, mark the electrical

connections and disconnect them. Remove the heaters

by unscrewing their mounting brackets from the fan

housings. When reinstalling the heaters, take care to not

over torque these fasteners.

5. Support the blower module by holding the motor.

Removing the (2) #12 hex head screws that secure the

blower module to the top channel with a 5/16”socket. This

operation may be easier with two people; one to support

the blower module and one to remove the screws.

6. Lower the blower module onto a workbench.

7. Using a 5/32" hex driver, loosen the set screws (one on

each fan) that secure the fan hubs to the motor shafts.

8. Remove the screws on the back of the blower plate that

secure the fan housings to the blower plate.

9. Slide the fan impellers and housings o of the motor shaft.

10. Detach the motor ground wire from the motor mount.

11. Remove the clips that hold the motor to the motor mount.

12. Replace in reverse order.

Figure 11 - Architectural Icon 08 (AI08) –

Replacing Fans /Motors

Figure 12 - Architectural Icon 10 (AI10) –

Replacing Fans /Motors

A. REPLACING FANS AND/OR MOTORS

CAUTION: ELECTRIC SHOCK HAZARD Disconnect power

whenever servicing unit. More than one disconnect may be

required to de-energize unit.

-10-

www.Berner.com/intelliswitch

NOTE – to navigate, use to select setting

use to change setting,

then press to enter the setting.

Stop: Immediately stops the air curtain and changes mode to OFF

"i": info button provides controller status and diagnostic data

Mode/Fan Speed:

Mode: Select your mode of operation (see next page)

Fan Speed: Sets the fan speed

Delay Time: Sets the amount of time the air curtain runs after the door closes

Temp Set: Sets the temperature the air curtain will maintain (heated units only)

Start Time: Programs the time of day the air curtain becomes active

Stop Time: Programs the time of day the air curtain stops running

Set Time/Day: Sets the clock time and day (used by programming)

Locked: Unit will run as programmed but settings cannot be changed

NOTE: Start/Stop time must be the same for the air curtain to operate continuously.

QUICK START INSTRUCTIONS

For your Berner Air Curtain with Intelliswitch™ Gen4

IMPORTANT NOTE!

If your air curtain unit is in “Locked” mode when you receive it:

Press and hold the for 5 seconds to unlock.

www.berner.com Berner International 800.245.4455

111 Progress Ave. / New Castle / PA / 16101 / USA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Berner Heizung Handbücher

Berner

Berner IDC12 Series Montage- und Bedienungsanleitung

Berner

Berner 180784 Bedienungsanleitung

Berner

Berner Pass-Thru 6 Series Montage- und Bedienungsanleitung

Berner

Berner GR Series Schulungshandbuch

Berner

Berner CHD10 Series Montage- und Bedienungsanleitung

Berner

Berner Architectural Elite 8 Montage- und Bedienungsanleitung

Berner

Berner Architectural High Performance 10 Montage- und Bedienungsanleitung

Berner

Berner K-ZONE KZN1030A Montage- und Bedienungsanleitung

Berner

Berner AE08 Montage- und Bedienungsanleitung

Berner

Berner B-22 Bedienungsanleitung

Berner

Berner DTU03-DTU03-1026 Bedienungsanleitung

Berner

Berner DIPLOMAT DP21036 Montage- und Bedienungsanleitung

Berner

Berner ALC08 Series Montage- und Bedienungsanleitung

Berner

Berner Zephyr Montage- und Bedienungsanleitung

Berner

Berner ARISTOCRAT Series Montage- und Bedienungsanleitung

Berner

Berner 129345 Bedienungsanleitung

Berner

Berner AC10 Montage- und Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung