BERNSTEIN DPG5019 Bedienungsanleitung
2
DPG5019
Les renseignements gurant dans cette notice de montage ne sont communiqués qu’à titre d’information et peuvent être
mis à jour sans préavis. Toutes les gures et dessins présents dans ces instructions sont uniquement à titre d’illustration
et n’ont aucune valeur d‘actualité.
This instructions should only be considered as a standard manual. Modications applied to updated version of the pro-
duct might not be mentioned inside this document. In this case, please just use the manual as a reference. The company
reserves modication rights.
Il seguente manuale è solo una guida standard. Nel caso in cui dovessero essere presenti errori, dovuti a eventuali modi-
che postume del prodotto, si prega di considerare il manuale unicamente come riferimento per il montaggio. L´azienda
si riserva il diritto di modica.
ERKLÄRUNG
STATEMENT
EXPLICATIONS
DICHIARAZIONE
Die Bedienungsanleitung dient nur als Referenz. Diese Anleitung kann abweichende Angaben enthalten.
Die beschriebenen Produkte können jederzeit aktualisiert werden. Die Zeichnungen in dieser Anleitung dienen nur zur
Darstellung und haben keinen Anspruch auf Aktualität.
3
DPG5019
Draw and drillfour holes on the wall.
Insert plastic expansile screw.Turn the screw clockwise.
Adjust the expansion link. Make sure the holder is
at the same line with ceiling.
Bottom view
4
DPG5019
FILL VALVE INSTALLATION
1. WORK PREPARATION
Remove the inoperative tank ttings and carefully clean the water cistern/tank.
Make sure all debris has been removed prior to installing new tank ttings.
WARNING
Do notuse or drop any chlorine or any chemical related components. Use of such products will:
Result in damage to tank components and may cause ooding and property damage and void warranty.
Do not overtighten nuts, or tank/bowl may crack.
2. FILL VALVE INSTALLATION AND WATER LEVEL ADJUSTMENT
1. Please read carefully the following installation instructions in
order to avoid component damage or injury to the installer.
2. The instructions have been composed based in the latest product
specications. We reserve the right to make modications to the
packaging and specications without providing prior notication.
3. When installing the ll valve,the critical level on the ll valve
(identied on the valve marked ”CL”) should be at least 1”)
above the top of the overow pipe of the ush valve.This is a
plumbing code.
4. We shall not be responsible for failures that are contributed to the
use of parts other than those specied.
5. Water Temperature: 2°C to 45°C.
6. Water Pressure Range: 0.2 Bar to 8 Bar.
Rell tube
overow pipe
bracket
bracket
bolt
overow
pipe
tank overow
pipe
water supply
pipe
inlet adaptor
water supply
switch
screw rod
bolt
1. Unscrew the bracket bolt and locate/install the ll valve onto overow pipe of ush valve.
2. Then tighten the bracket bolt.
3. Connect water supply into inlet shank , turn on the water supply valve (angle stop) (Make sure that rell tube has
been inserted in the ush valve overow pipe in the event the toilet requires rell to the bowl).
4. Check if the inlet valve is under normal operation and adjust the inlet valve oat adjustment thumbscrew clockwise
(for higher oat & water level) or anticlockwise (for lower oat & water level) according to the requirements.
u v w x
5
DPG5019
4. TROUBLESHOOTING
Issue - Cause - Resolution
Water line is too high or too low.
Inlet valve is not adjusted to a suitable position. Adjust the water level to the appropriate water level.
Inlet valve does not shut off.
The cistern/tank wall has blocked the movement of the inlet valve oat. Adjust the ll valve and make sure oat can move freely.
The rell tube wasn’t installed properly. See gure attached 3.7 to re-install rell tube correctly.
Leakage of ush valve. Make sure none leakage of ush valve.
The water level is above overow pipe of ush valve. Re-adjust water level to appropriate.
Inlet valve does not turn on.
Water supply valve/angle stop is off. Turn on the water supply valve/angle stop.
The cistern/tank wall has blocked the movement of the inlet valve oat. Adjust the ll valve and make sure oat can move freely.
Filter screen is dirty. Clean lter screen.
3. CLEANING FILTER (Filter which is located inside the inlet valve shank is required for cleaning periodically).
inlet connector
bracket
water supply
pipe
water supply
pipe
Wrongly placed rell tube
Adjust rell tube, make sure tube
is above the water line.
water level
tank
tank
overow
pipe
lter
lter
inlet connector
inlet connector
water
supply switch
water
supply switch
nut
nut
lter
bolt
1. Shut off the water supply valve (angle stop) then remove the water supply line from the inlet adaptor.
2. Unscrew the bracket bolt and remove the ll valve.
3. Unscrew ll valve nut, remove inlet connector, nut and lter.
4. Clean the lter screen with water.
5. Install back the clean lter and inlet connector.
(Note: The opening of inlet connector goes into the inlet body and screw up the nut).
6. Reference point two of „FILL VALVE INSTALLATION AND ...“ to re-install the ll valve and turn on water supply.
u v w
y
x
z{
Inhaltsverzeichnis
Andere BERNSTEIN Badezimmerarmatur Handbücher
BERNSTEIN
BERNSTEIN G3005A Bedienungsanleitung
BERNSTEIN
BERNSTEIN 3011 Basic Bedienungsanleitung
BERNSTEIN
BERNSTEIN FLEXGT02 Bedienungsanleitung
BERNSTEIN
BERNSTEIN NT6192 Bedienungsanleitung
BERNSTEIN
BERNSTEIN DX906 FLEX Bedienungsanleitung
BERNSTEIN
BERNSTEIN 1238 Handbuch
BERNSTEIN
BERNSTEIN EX426 Bedienungsanleitung
BERNSTEIN
BERNSTEIN NT7562 Bedienungsanleitung
BERNSTEIN
BERNSTEIN 805S Bedienungsanleitung
BERNSTEIN
BERNSTEIN NT7177 Bedienungsanleitung
BERNSTEIN
BERNSTEIN ARCTIC Freestanding cabinet 140 Bedienungsanleitung
BERNSTEIN
BERNSTEIN NT3127 Bedienungsanleitung
BERNSTEIN
BERNSTEIN NT6705 Bedienungsanleitung
BERNSTEIN
BERNSTEIN EX506 Bedienungsanleitung
BERNSTEIN
BERNSTEIN DX906 FLEX Bedienungsanleitung
BERNSTEIN
BERNSTEIN EX101 Bedienungsanleitung
BERNSTEIN
BERNSTEIN NT3311 Bedienungsanleitung
BERNSTEIN
BERNSTEIN FlexM03 Bedienungsanleitung
BERNSTEIN
BERNSTEIN FSL-900 Bedienungsanleitung
BERNSTEIN
BERNSTEIN TLB150 Bedienungsanleitung
