Beta RR4T USA 400 Bedienungsanleitung
RR4T USA - RS4T USA
400 - 450 - 525
RR4T USA - RS4T USA
400-450-525
The information described in this enclosure are updates to
the Europe version
Label location RR4T USA ............................................ 2
Label location RS4T USA ............................................ 3
Controls RR4T USA .................................................... 4
Controls RS4T USA.................................................... 5
Digital speedometer RR4T USA - RS4T USA.................... 6
Wiring diagram RR4T USA ....................................... 10
Wiring diagram RS4T USA ....................................... 12
Fuel cock ............................................................... 14
Choke .................................................................. 15
Adjusting the slow running ........................................ 15
Canister filter .......................................................... 16
2
USA
LABEL LOCATION RR4T USA
Label RR4T:
1 – Warnings plate
2 – Brake oil plate
3 – Technical plate
4 – Eco-plate
4
1
2
23
3USA
label RS4T:
1 – Warnings plate
2 – Brake oil plate
3 – Technical plate
4 – Eco-plate
5 – Vapour recovery diagram (under saddle)
1
4
3
5
2
LABEL LOCATION RS4T USA
2
4
USA
CONTROLS RR4T USA
RH SWITCH
Starte button 1 is located on the right-hand
side of the handlebars and operate the
electri engine starter. Push the button until
the engine sterts.
Do not press the button 1 while the engine
is running.
LH SWITCH
Switch 2is used to stop the engine. Press
the button until the engine stops.
While button 3 turns on the lights
1
3
2
5USA
2
1
CONTROLS RS4T USA
RH SWITCH
Starte button 1 is located on the right-hand
side of the handlebars and operate the
electri engine starter. Push the button until
the engine sterts.
Do not press the button 1 while the engine
is running.
While button 2 turns off the engine.
Caution:
Before turning it on, make sure the switch
2 is on ON.
LH SWITCH
Dip switch 3has three positions:
A= lights off
B= low beam on
C= high beam on
Button 4operates the horn.
Switch 5is used to stop the engine. Press
the button until the engine stops.
Shifting lever 6 left or right activates the
left or right indicators (if istalled). When
released, the returns to the central posi-
tion. Press it to turn the indicators off.
ON OFF
3
4
5
6
6
USA
DIGITAL SPEEDOMETER RR4T USA
Note:
Information for setting the RR4T USA digital dashboard is in the Main Manual and
vehicles for the US market are factory set in Mph.
DIGITAL SPEEDOMETER RS4T USA
CYCLING THROUGH THE FUNCTIONS
It is always possible to cycle through the different functions while the vehicle is stationary
or in motion. Pressing button C or D displays the following functions in succession:
TIME - LAP - TOD - TD - COUNTDOWN
BUTTON FUNCTIONS
The functions of the buttons change with the function currently displayed:
1 - TIME .......................... T≥3” and Vel=0 activates time setting mode - T<3” or
Vel>0 cycles through functions
2 - LAP ............................ T≥3” resets LAP and TD - T<3” cycles through functions
3 - TOD .......................... T≥3” and Vel=0 enables setting of circumference, unit and
number of pulses for each wheel turn - T<3” or Vel>0 cycles
through functions
4 - TD .............................T≥3” resets LAP and TD - T<3” cycles through functions
5 - COUNTDOWN .......... T≥3” and Vel=0 enables setting of countdown - T<3” or
Vel>0 cycles through functions.
T = Time during which button is pressed down
Vel = Speed of vehicle
7USA
CURRENT SPEED FUNCTION
This information is constantly displayed to-
gether with an indication provided by a
graphic bar. The default unit is Mph. To
change the unit, press the button to access
the Setup menu and select km/h. When Mph
is selected, no indication is provided as to
which unit is currently displayed.
1 - TIME FUNCTION (TIME)
T≥3” and Vel=0 activates time setting mode
T<3” or Vel>0 cycles through functions
The time can only be set while the vehicle is stationary.
Press and hold button C or D for more than 3 seconds to enter the time setting mode.
Once the time has been set, press the button for about 3 seconds to go back to the
standard operating mode. The Time parameter is displayed in the 0-12 format if Mph
has been selected, and in the 0-24 format if Km/h has been chosen. When in the setting
menu, if no buttons are pressed for 20 seconds the system will automatically return to the
standard operating mode.
Moving off (Vel > 0) while the setting mode is activated causes the system to automati-
cally return to the standard operating mode.
2 - AUTOMATIC LAP FUNCTION (LAP)
T≥3” resets LAP and TD
T<3” cycles through functions
This information represents the actual riding time associated with the TD parameter. It is
an automatic counter which is activated by the first pulse generated by the speed sensor
and stops 3 seconds after receiving the last pulse from the sensor. The counter for this
parameter can be reset while in LAP mode by pressing the C or D button for about 3
seconds until 00’00” is displayed. The LAP function can be reset while the vehicle is
stationary or in motion and also causes the reset of the TD parameter.
3 - MILEOMETER FUNCTION (TOD)
T≥3” and Vel=0 enables setting of circumference, unit and number of pulses for each wheel turn
T<3” or Vel>0 cycles through functions
The information is displayed together with the TOD caption. Depending on the selected unit, the
informat is displayed in Mph (default) or Km/h and is permanently stored in non-volatile memory.
It is not possible to reset this information during normal operation of the instruments.
8
USA
4 - AUTOMATIC TRIP FUNCTION (TD)
T≥3” resets LAP and TD
T<3” cycles through functions
This function is always accompanied by the TD caption. The information displayed
represents the total distance covered by the vehicle in kilometres or miles (according to
the selected unit). It is an automatic counter which is activated by the first pulse
generated by the speed sensor.
The counter for this parameter can be reset while in TD mode by pressing the button
for about 3 seconds until 000.0 is displayed. The TD function can be reset while the
vehicle is stationary or in motion and also causes the reset of the LAP parameter.
5 - COUNTDOWN TRIP FUNCTION (Countdown)
T≥3” and Vel=0 enables setting of countdown
T<3” or Vel>0 cycles through functions
This function is always accompanied by a flashing TD caption. The counter is always
active and is automatically decreased by 0.1 kilometres or miles according to the
selected unit. The value for this parameter can be changed in TD decrease mode by
pressing the button for about 3 seconds while the vehicle is stationary.
The different figures that make up the counter can be altered starting from the most
significant figure and shifting in successive steps to the least significant figure.
Pressing the button for a short time decreases the value by one step; pressing it for a
longer time allows a different parameter to be selected. After setting the least signifi-
cant figure, press the button for about three seconds to go back to the standard
operating mode. If the parameter reaches 000.0, the system automatically sets it to
999.9.
While in the setting menu, if no buttons are pressed for 20 seconds the system will
automatically return to the standard operating mode.
Moving off (Vel > 0) while the setting mode is activated causes the system to automati-
cally return to the standard operating mode
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Beta Motorrad Handbücher
Beta
Beta Motard M4 Bedienungsanleitung
Beta
Beta RR 2T ENDURO 2014 250 Leitfaden
Beta
Beta RR 250 2T EUROPA 2019 Bedienungsanleitung
Beta
Beta REV 3 Bedienungsanleitung
Beta
Beta Evo4t 300 Bedienungsanleitung
Beta
Beta 400 RS 2014 Bedienungsanleitung
Beta
Beta RR 4T-400 Gebrauchsanweisung
Beta
Beta X-Trainer 300 2T Bedienungsanleitung
Beta
Beta RR 4T ENDURO 2014 350 Leitfaden
Beta
Beta REV 80 Bedienungsanleitung
Beta
Beta RR 125 LC Bedienungsanleitung
Beta
Beta RR 50 CC series Bedienungsanleitung
Beta
Beta Evo 80 Senior Bedienungsanleitung
Beta
Beta 2009 Evo 2T 125 Bedienungsanleitung
Beta
Beta RR 50 cc ENDURO Bedienungsanleitung
Beta
Beta 250-300 RR Handbuch
Beta
Beta X-Trainer 300 2T Bedienungsanleitung
Beta
Beta TECHNO 250 Bedienungsanleitung
Beta
Beta EVO 4T Bedienungsanleitung
Beta
Beta RR 300 2T Bedienungsanleitung
Beliebte Motorrad Handbücher anderer Marken
MOTO GUZZI
MOTO GUZZI QUOTA 1100 ES Bedienungsanleitung
APRILIA
APRILIA ETV MILLE CAPONORD - PART1 02-2001 Bedienungsanleitung
Yamaha
Yamaha 2006 YZF-R1V Bedienungsanleitung
KTM
KTM Freeride E-XC 2021 Bedienungsanleitung
Fantic
Fantic Enduro 125 Bedienungsanleitung
Ducati
Ducati Supersport 750 desmodue Bedienungsanleitung
