Betz WAVE Bedienungsanleitung
betz-tools.com
1
Manual
The camera weight has always be adjusted in the radius of the center of gravity! (A)
Use Motors and Accessories to keep the Cameras rotating point Balanced
to the optical axis
A
In upside down mode never mount the camera on its handle!
This way of mounting will cause vibration. It is easy to flip the picture.
A
Camera and Wave mounting
Rear Front
40mm
1,57”
77mm
3”
142mm
5,59”
Attach camera with mounted dovetail plate and make sure that all parts
and the camera itself is fixed perfect and nothing can vibrate.
Make sure that the clamp lever on the stage faces to the rear (A) so that
the clamping is open. After the camera snaps in, the clamp lever snaps to
the front. The camera is now protected against sliding out.
Never close or operate the closer mechanism by force.
By pulling the clamp lever towards stage rear, approximate fore/aft balance
can now be achieved by sliding of the camera in the stage.
The clamping lever should lock the camera even before being pressed
to the final stop!
In case the camera can still be moved even though the lever is pressed
until stop cause of different tolerances of the dovetailplates a spacer of
approx. 0,1 mm (0.004”) has to be put under the compensation track un-
der the cover plate. (see maintenance)
To remove the camera, the dovetail clamp must be opened by pulling the
clamp lever fully to stage rear.
Mounting the Wave onto a device:
Bottom side you will find two 3/8” threads and also four M5 threads.
Mounting Template
L
O
C
K
P
I
N
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
Frontside and Basics to Start
Power LED: On = Ready to go
Flashing = ”Zero” Initialisation ca. 5 sec.
Locked LED: On = Lock Pin engaged
Flashing = Fault Restart
CAN LED: On = External CAN Device is connected.
Wave must be in a leveled position before connecting to power.
Power LED flashes keep Wave in position ”Zero” Initialisation runs for about 5 sec.
Lock Pin must be engaged before turning into ”upside down” mode.
Lock Pin
unlock pull and turn
Spirit level to adjust
the Horizon
CAN 10 - 36 V DC IN
USBSD-Card
Horizon
Setup
#160313
RAMP
M-POWER
max.
Made in Germany
Menu Button and
Adjustment Knob for Setup
Control Panel
Fine adjustment Horizon
Serial# Slot Micro SD-Card
for Software upgrades
USB-B
for external Software
Set Up
BT CAN-BUS
External control device
from our CAN Toolset
Lemo 0B 304
soldering side connector
+12V
GND
CANH
CANL
Lemo 1B 303
soldering side connector
+12V
GND
DC Power Input:
10 - 36 Volt
Power Consumption:
500mA peak 2,5A
From a certain point of the Tilt-Angle it doesn‘t make sense to stabilize the horizon. For this reason the
stabilization of the horizon will be frozen in a defined Tilt angle.
The Tilt angle can be adjusted individually as follows.
Push Button USBSD-Card
Horizon
Setup max.
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
SET UP Tilt Angle
Push Button Setup Push Button Setup Push Button Setup 3 sec. Push Button Setup
Green flashes
Bring device in desired Tilt-
position
Green
Tiltangle
short flashing
Tiltangle stored
All LEDs on
Menu started
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
The basic setting for the motor power is fine for a wide range of camera weights.
If the power is adjusted too strong you will feel it in jerkily movements or a vibration.
If the power is adjusted too weak you will see it in creeping movements to the end point.
The motor power can be adjusted very easily as follows.
Adjustment Knob
USBSD-Card
Horizon
Setup max.
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
SET UP Motor Power
Push Button Setup Push Button Setup Push Button Setup Push Button Setup 3 sec. Push Button Setup
Red flashes
set M-Power via Poti
Green
Tiltangle
short flashing
M-Power stored
All LEDs on
Menu started
Red
Setup M-Power
Setup
RAMP
M-POWER
max.
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
Push Button
Push Button Setup Push Button Setup Push Button Setup Push Button Setup Push Button Setup 3 sec. Push Button Setup
SET UP Ramp
Blue flashes
set Ramp via Poti
Green
Tiltangle
short flashing
Ramp stored
All LEDs on
Menu started
Ramp is the speed when the frozen Horizon switches from the adjusted Tiltangle back to stabilization.
Ramp can be adjusted very easily as follows:
Red
M-Power
Setup
RAMP
M-POWER
max.
USBSD-Card
Horizon
Setup max.
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
POWER
CAN
LOCKED
M-POWER
RAMP
TILT ANGLE
Blue
Setup Ramp
Push Button
Adjustment Knob
Trouble Shooting
Power LED flashes / Locked LED flashes 1/2/3/4 or 5 times switch off Wave and restart after about 5 sec.
If the error remains contact the manufacturer.
Power LED continously flashes. Switch off Wave and restart after about 5 sec.
Wave stops in one direction far from the endstop or the Horizon can‘t be adjusted to the level.
The IMU has lost for some unknown reason the ”zero position”.
Preperation for recalibrating the ”zero position” :
It is very Important that the power supply is designed for 3 Amp. at 14 Volt.
It is very Important that the Wave is placed on a solid and horizon oriented level surface.
The camera quicklockplate has to be placed in mechanical ”zero position” and the Lok Pin
is not be locked. Power supply is switched off.
Calibrating Set up ”zero position”
- Push button ”Set up” and hold, switch on power supply.
- Push button while the green and blue LED is permanent on.
- Release Push button the electronic ”zero position” will now be adjusted.
- Red LED flashes fast, engage Lok Pin, red LED is permanent on.
- Wave determines now the mechanic ”zero position” and stores it into the memory.
- Wait until green LED flashes slow and the red LED is permanent on.
- Setup is now finished switch off power supply and restart the Wave.
Warning! Disassembling the Wave will result in the unit having to be returned to the manufacturers
for an electronic and mechanical rest.
Maintenance
The Wave is a maintenance-free sturdy electromechanical device. To guarantee a proper function you
have to comply to the following points:
- Keep the eight roller guidance and the roller track clean!
- If the camera rocker hooks or the roller guidance get‘s loose please ask how to service and to adjust.
Isn‘t that easy?
Quicklockplate:
The locking mechanism should be treated/cleaned occasionally with a resinless oil (e.g. gun oil).
Placing a spacer in the locking mechanism:
unscrew screws
remove cover plate unscrew screws
place spacer inbetween
main spacer and slider
Inhaltsverzeichnis
Andere Betz Kamerazubehör Handbücher
