BFM Europe Avelli Montageanleitung

Avelli

BA ANCED F UE OG EFFECT GAS FIRE

Installation, Maintenance & User Instructions

Hand these instructions to the user

Model No’s BBF **RN2 is only for use on Natural Gas (G20) at a

supply pressure of 20 mbar in G.B. / I.E.

** denotes cosmetic variant

CONTENTS

PAGE

Section 1 Information and Requirements

1.0 Appliance Information 3

1.1 Conditions of Installation 4

1.2 Fireplace surround & suitability 4

1.3 Flue Terminal Position 5

1.4 Shelf position 6

1.5 Hearths 6

Section 2 Installation of Fire

2.1 Unpacking the fire 6

2.2 Fireplace opening 7-8

2.3 Preparation of the wall 8-9

2.4 Preparation of the flue hole 9

2.5 Installation of the gas supply 10

2.6 Preparation of the flue duct 11

2.7 Securing the firebox to the opening 12-13

2.8 Installing the Avelli surround 14-15

2.9 Centralising the surround legs 16

2.10 Making the gas connection / pressure testing 17

2.11 Fitting the terminal guard 17

2.12 Removal & refitting of the glass frame 18-20

2.13 Removal & refitting of the burner assembly 21-22

2.14 Fitting the batteries to the receiver and handset 23

Section 3 Assembling Fuel Bed and Commissioning

3.1 Fitting the log fuel bed 24-28

3.2 Lighting the appliance 29-33

3.3 Fitting the handset wall bracket 33

3.4 Instructing the user / product handover 33

Section 4 Maintenance

4.1 Removal of the burner assembly 34

4.2 Removal of the gas valve 34

4.3 Removal of the pilot assembly 35

4.4 Removal of the receiver 35

Parts shortlist 36

Section 5 User Instructions

5.1 Installation Information / about your fire 37-38

5.2 Operating your fire 39-43

5.3 Removal / replacing the glass frame 44-46

5.4 Removal / replacing the log fuel-bed 47-51

5.5 Cleaning instructions 51-52

5.6 Replacement of batteries in the receiver and handset 52

User replaceable parts 53

This appliance is manufactured by :-

BFM Europe Ltd, Trentham Lakes,

Stoke-on-Trent, ST4 4TJ.

SECTION 1

INFORMATION AND REQUIREMENTS

1.0 APP IANCE INFORMATION

Model BBFL**RN2

** denotes cosmetic variant of product

Gas Type G20

Main injector (1 off) Size 380

Pilot Type Black Technigas “Polidoro” G27.2

Max. Gross Heat Input : 5.7 kW

Min. Gross Heat Input : 4.4 kW

Gas Rate : 0.529 m3/hr

Cold Pressure : 20.0 +/-1.0 mbar

Ignition : 6V Battery Ignition

Electrode Spark Gap 4.0mm

Packed Weight 48 kg

Gas Connection : 8mm Compression (supplied with fire)

Fig. 1

INSTA ATION REQUIREMENTS

Efficiency Declaration

The efficiency of this appliance has been measured as specified in

BS EN 613 : 2001 and the result after conversion to Gross using the

appropriate factor from Table 4 of SAP 2009 is 76%. The test data from which it

has been calculated has been certified by BSI. The efficiency value may be used

in the U Government’s Standard Assessment Procedure (SAP) for energy rating

of dwellings.

1.1 CONDITIONS OF INSTA ATION

It is the law that all gas appliances are installed only by a GAS SAFE Registered

Installer, in accordance with these installation instructions and the Gas Safety

(Installation and Use) Regulations 1998 as amended. Failure to install appliances

correctly could lead to prosecution. It is in your own interest and that of safety to

comply with the law.

The installation must also be in accordance with all relevant parts of the Local and

National Building Regulations where appropriate, the Building Regulations

(Scotland Consolidation) issued by the Scottish Development Department, and all

applicable requirements of the following British Standard Code of Practice.

1. B.S. 5871 Part 1 Installation of Gas Fires

2. B.S. 6891 Installation of Gas Pipework

3. B.S. 5440 Parts 1 & 2 Installation of Flues and Ventilation

4. I.S 813 : 1996 Domestic Gas Installation, issued by the National Standards

Authority of Ireland.

1.2 FIREP ACE / SURROUND SUITABI ITY

The fire must only be installed with the hearth supplied it must not be installed

directly onto carpet or other combustible floor materials.

If a heating appliance is fitted directly against a wall combustible material must be

removed from behind it. Soft wall coverings such as blown vinyl, wall paper etc.

could be affected by the rising hot air and scorching and/or discoloration may

result. Due consideration should be made to this when installing or decorating.

This product can only be installed with surround designs available from BFM

Europe td or designs which meet the criteria as required by BFM Fires. For

further details of specification requirements please contact BFM Europe

Technical Service.

1.3 F UE TERMINA POSITION

The minimum acceptable dimensions from the flue terminal to obstructions

and ventilation openings are shown below and listed in the table

It is important that the position of the flue allows the free passage of air

across it at all times. The minimum acceptable space from the flue terminal

to obstructions and ventilation openings are specified below (fig. 2)

Fig. 2

DIMENSION TERMINA POSITION MINIMUM DIMENSION

A Directly below an opening, air brick, 300mm (12in)

opening window

B Above an opening, air brick, 300mm (12in)

opening window

C Horizontally to an opening, air brick, 300mm (12in)

opening window etc.

D Below gutters, soil pipes or drain pipes 300mm (12in)

E Below eaves 300mm (12in)

F Below balconies or car port roof 600mm (12in)

G From a vertical drain pipe or soil pipe 300mm (12in)

H From an internal or external corner 600mm (24in)

I Above ground roof or balcony level 300mm (12in)

J From a surface facing the terminal 600mm (24in)

K From a terminal facing the terminal 600mm (24in)

From an opening in the car port 1200m (48in)

M Vertically from a terminal on the same wall 1500mm(59in)

N Horizontally from a terminal on the 300mm (12in)

same Wall

O NOT APP ICAB E N/A

P NOT APP ICAB E N/A

Q NOT APP ICAB E N/A

1.4 SHE F POSITION

The fire may be fitted below a combustible shelf providing there is a minimum

distance of 200mm above the top of the fire and the shelf does not project more

than 150mm. If the shelf overhangs more than 150mm the distance between the

fire and the shelf must be increased by 15mm for every 25mm of additional

overhang over 150mm.

1.5 HEARTHS

This appliance must only be installed with the BFM Europe supplied hearth panel

or an alternative item as dimensionally approved by BFM Europe.

SECTION 2

INSTA ATION OF FIRE

2.1 UNPACKING THE FIRE

Carefully lift the fire out of the carton. Remove the loose item packaging carefully

from the front of the appliance. Check the contents as listed :-

Packing Check List - All Models

Pack 1 of 2 - Combustion Chamber Pack

1 off Combustion chamber & glass frame assembly

1 off Boxed ceramic fuel-bed set (packed inside combustion chamber)

1 off Wall plate

1 off Flue terminal / pipe unit

1 off Flue terminal guard

1 off Installation / user book (combined)

1 off Loose items pack – containing :- 1 off 9V battery, 4 off 1.5V batteries

remote handset, 1 off handset wall

brkt (inc. fixings), 1 off glass removal

tool, 4 off M5 locknuts, 4 off 8mm

rawlpugs & fixing screws, 2 off

surround leg securing brackets.

Pack 2 of 2 - imestone or Travertine Surround

1 off Hearth 1 off L/H leg

1 off Shelf 1 off R/H leg

1 off Top infill 1 off Controls access panel

1 off Shelf infill section

1 off Firebox / burner assembly

2.2 FIRE P ACE OPENING

a) The front opening of the fire place must be between 550 and 565mm

wide and between 785mm and 795mm high. If the opening exceeds

these dimensions then a surround must be constructed from suitable

non-combustible material to produce a suitable sized opening. Any

surround must be suitably sealed to the fire place to prevent leakage.

See fig. 3 below

Fig. 3

b) The minimum / maximum sized distances between the firebox mounting

flange and outside wall are shown below and overpage in fig. 4 & 5

Fig. 4

550mm minimum,

565mm maximum

Fire Opening

785mm minimum,

795mm maximum

Minimum Flat

ealing Area

10mm

Minimum Installation

Depth 358mm

Maximum Installation Depth

651mm

Fig. 5

2.3 PREPARATION OF THE WA

a) The appliance and flue pipes must be installed at right angles to the

mounting wall. The appliance itself should be installed vertically against

a flat wall. Where an uneven wall surface is found, appropriate action

should be taken to ensure that the appliance is not stressed or does not

distort when installed.

b) Ensure that the floor surface onto which the appliance is mounted onto

is flat. The minimum height from the floor to the centre of the flue is

shown on fig. 6 overpage.

1115mm

550mm 228mm

Outer Wall

600mm Including

Firebox Flanges

300mm

Cavity

Flue Terminal

Fig. 6

2.4 PREPARATION OF THE F UE HO E

a) Mark the position of the centre of the flue on the inner wall.

b) Cut hole for outer flue pipe. There are two possible methods to achieve

this, either core drill or via hammer and chisel.

c) To core drill, proceed as follows :-

Drill a pilot hole through the wall, in position as specified in figure 6.

Using a 6” core drill, drill the flue hole.

To Hammer and chisel, proceed as follows :-

Mark the position of the centre of the flue pipe as specified in figure 6.

Mark the position of the hole around this point.

Chisel out the area as marked on the wall.

d) We then recommend that a cardboard cylinder is placed around the flue

pipe and inserted in the chiselled out hole whilst making good.

NOTE :- If the appliance is to be installed into a building under

construction, it is recommended that a non-corrosive metal

tube of 6” diameter be inserted into the position of the hole.

150mm diameter

582mm

2.5 INSTA ATION OF THE GAS SUPP Y

a) Before installing the firebox, decide from which side or if a rear

connection to the gas supply is required. Plan the pipe run to enter the

firebox from the left, right or rear and connect to the inlet elbow. See

below :-

b) If concealed pipe work is required plan the pipe run to enter the fire box

through the openings in the rear of the fire box and connect to the inlet

elbow. See fig. 7 & 8 below for a suggested concealed pipe layout.

Fig. 7

Fig. 8

Note : Before breaking into the gas supply a pressure drop test should be

carried out to establish that the existing pipework is sound. Always re-fit the

gas inlet plate to the rear entry point and secure with the screws provided.

Firebox

Fireplace

Gas upply

Firebox

Approx.

525mm Fireplace

Gas upply

Approx.

100mm

Andere Handbücher für Avelli

Inhaltsverzeichnis

Andere BFM Europe Kamin im Innenbereich Handbücher

BFM Europe

BFM Europe Passion Series Montageanleitung

BFM Europe

BFM Europe Eden Elite Montageanleitung

BFM Europe

BFM Europe GICCI2MN Montageanleitung

BFM Europe

BFM Europe Celena Montageanleitung

BFM Europe

BFM Europe Arana RC Bedienungsanleitung

BFM Europe

BFM Europe Da Vinci Illumia MK2 Montageanleitung

BFM Europe

BFM Europe The Collection Da Vinci Illumia Montageanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung