Bholanath BH-MSD-8A Bedienungsanleitung

BH-

MSD

User’s Manual

For

MSD

-8A Micro Stepping Driver

Website:-www.bholanath.in

E-mail id:-support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

Page |

WARNING:-DO NOT GIVE DIRECT SUPPLY OF 230 VAC. AS THIS WOULD

DAMAGE THE DRIVE. PLEASE USE THE TRANSFORMER OF OUPUT RANGE

120VAC FOR THIS DRIVE.REFER OUR 120 VAC TRANSFORMER MODEL BH-120

VOLTS AC.

Pro uct Number co e for Micro step rive

BH MSD 8A

8 Amp

MICRO STEP DRIVE

BHOLANATH

1. DC Power input : AC Power input:110 VAC~220 VAC

2. Output Current: 0.5 Amp-8 Amp

3. MICRO Steppin : 1, 2, 4, 8, 16, 32, 64, 128, 256, 5, 10, 20,

25, 40, 50, 100, 200, 256

4.Protect form: overheat, lock automatic half current, error connect protect

5.Dimension: 195mmx107mmx81mm

6. Wei ht: 1500 .

7. Workin environment:Temperature-15~40⁰C Humidity<90%

Website:-www.bholanath.in

E-mail id:-support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

Page |

Table of Contents

1. Introduction, Features and Applications

...........................................................

Introduction

..............................................................................................

Features

....................................................................................................

Applications

..............................................................................................

2. Specifications

...............................................................................................

Electrical Specifications

.............................................................................

Model no:-BH-MSD-8A

....................................................................

Drive prevention

........................................................................................

Operating Environment

..............................................................................

Elimination of Heat

....................................................................................

3. Pin Assignment and Description

......................................................................

Connector P1 Configurations

......................................................................

Connector P2 Configurations

......................................................................

External Limiting Resistance................................................................................

Full current And Half current ...............................................................................

Wiring Notes......................................................................................................... 6

Switch Choice ....................................................................................................... 6

4. Sequence Chart of control Signals

...................................................................

5. Calculation Of pulse Frequency

......................................................................

Frequency with Different RPM At 400 Micro Step.............................................. 7

Frequency with Different RPM At 800 Micro Step.............................................. 7

6. Connecting the Motor

....................................................................................

Connections to 4-lead Motors

......................................................................

Connections to 6-lead Motors

......................................................................

Half Coil & Full Coil Configurations

....................................................

Connections to 8-lead Motors

...............................................................

Series Connections

..............................................................................

Parallel Connections

...........................................................................

7. Power Supply Selection

.................................................................................

Regulated or Unregulated Power Supply

.......................................................

Multiple Drivers

........................................................................................

8. Troubleshooting

............................................................................................

9. Dimensions

................................................................................................

10. . Circuit connections Of BH MSD 8A With BH SDC-01,02

......................... .

11. Circuit connections of BH MSD 8A With Arduino & PLC

............................. .

12. Frequently Asked Questions

.......................................................................

13. Contact Us

................................................................................................

Website:-www.bholanath.in

E-mail id:-support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

Page |

1. Introduction, Features and Applications

Introduction

Micro stepping driver is particularly suitable for the applications desired with extremely low noise

and low temperature rise technology which significantly improve the performance of the stepper

motor that leads to low temperature rise, low vibration. With the adjustment technology (step/rev and

current) according to different motors, the driven motors automatically generate optimal parameters

for different motors, and achieve the best performance at higher speed. It is suitable for driving 2-

phase and 4-phase hybrid stepping motors.

Features

High performance, cost-effective

Suitable for 2-phase and 4-phase motors

Support PUL/DIR and CW/CCW modes

Short-voltage, over-voltage, over-current and short-cicuit protection

Low temperature rise, smooth motion

Pulses Response Frequency Can Reach 200KHz

Applications

Suitable for a wide range of stepping motors, from NEMA size 17 to 34. It can be used in various

kinds of machines, such as X-Y tables. And a variety of large-scale automation equipments and

instruments. For example: labeling machine, cutting machine, packaging machine, plotter, engraving

machine, CNC machine tools and so on. It always performs well when applied for equipment which

requires for low-vibration, low-noise, high-precision and high-velocity.

2. Specifications

Electrical Specifications

Model No:-BH-MSD-8A

Parameter

Min

ypical

Max

Unit

Input

Voltage(DC)

- VDC

Input

Voltage(AC)

110

220

VAC

Output current

0.5

DRIVE PREVEN ION :-

NO E:- HE ABOVE VOL AGE AND CUREN MAY DIFFER BU I IS RECOMMENDED O USE ABOVE

VOL AGE AS I WILL PREVEN DRIVE FROM DAMAGE AND AS FOR CURREN I MAY DIFFER AS PER

MICROS EP DRIVE.

Operating Environment

Cooling Natural cooling or Forced cooling

Operating Environment Environment-Avoid dust, oil fog, corrosive gases

emperature- -10℃

℃℃

℃－

－－

－45℃

℃℃

℃

Humidity-Not Condensation,No Water Droplets

Operating Temperature- -10℃

℃℃

℃-

-45℃

℃℃

℃

Storage emperature -20℃

℃℃

℃－

－－

－65℃

℃℃

℃

Website:-www.bholanath.in

E-mail id:-support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

Page |

Elimination of Heat

Driver’s reliable working temperature should be <70

℃

℃℃

℃

, and motor working temperature

should be <80

℃

℃℃

℃

;

It is recommended to use automatic idle-current mode, namely current automatically reduce

to 60% when motor stops, so as to reduce driver heating and motor heating;

It is recommended to mount the driver vertically to maximize heat sink area. Use forced

cooling method to cool the system if necessary.

3. Pin Assignment and Description

The driver has two connectors namely P1 & P2, Connector P1 for control signals connection,

Connector P2 for power and motor connections.

The following tables are brief descriptions of the two

connectors.

Connector P1 Configurations

Pin Function Details

PUL+,CP+ PULSE SIGNAL POSITIVE

PUL-,CP- PULSE SIGNAL NEGATIVE

DIR+,CW+ DIRECTION SIGNAL POSITIVE

DIR-,CW- DIRECTION SIGNAL NEGATIVE

ENA+,FREE+ ENABLE SIGNAL POSITIVE

ENA-,FREE- ENABLE SIGNAL NEGATIVE

Connector P2 Configurations

Pin Function Details

AC AC POWER SUPPLY

AC GROUND

A+,A- MOTOR PHASE A

B+,B- MOTOR PHASE B

PE GROUND TERMINAL FOR DRIVER

EXTERNAL CURRENT LIMITING RESISTANCE:

Signal current in both the“+” “-”ports,

can’t be too big and not too weak. It is necessary to connect current-limiting resistor in external if the

signal amplitude is too strength, refer to following table

VOLTAGE LIMITING RESISTANCE(R )

5 V R=0

12 V R=1KΩ

24 V R=2.2 KΩ

NO E: FULL CURREN AND HALF CURREN CHOICE: (POR SW 5)

FULL CURREN :-IF HE DRIVER IS IN FULL CURREN MODE HIS WILL LEAD O MO OR HEA AND I

WILL ALSO DAMAGE HE DRIVER.

HALF CURREN :- HE DRIVER SHOULD ALWAYS BE IN HALF CURREN MODE AS HIS WILL REDUCE

HE HEA OF MO OR AND DRIVER.

Website:-www.bholanath.in

E-mail id:-support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

Page |

Wiring Notes

To prevent noise incurred in PUL/DIR signal, pulse/direction signal wires and motor wires

should not be tied up together. It is better to separate them by at least 10 cm, otherwise the

disturbing signals generated by motor will easily disturb pulse direction signals, causing

motor position error, system instability and other failures.

If a power supply serves several drivers, separately connecting the drivers is recommended

instead of daisy-chaining.

It is prohibited to pull and plug connector P2 while the driver is powered ON, because there is

high current flowing through motor coils (even when motor is at standstill). Pulling or

plugging connector P2 with power on will cause extremely high back-EMF voltage surge,

which may damage the driver.

Switch Choice: (“ON=0，OFF=1”)

1.Microstepping choice:

SW 7 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

SW 8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1

SW 9 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1

SW 10 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

MICROSTEP 1 2 4 5 6 8 10 16 18 20 32 40 50 64 128 256

2. Current choice

：

：：

：

SW 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0

SW 2 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0

SW 3 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0

SW 4 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

CURRENT(A) 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8

4.Sequence Chart of Control Signals

In order to avoid some fault operations and deviations, PUL, DIR and ENA should abide by

some rules, shown as following diagram

NOTE:

Enable signal is always high in this drive. Any external supply of 5 Vdc applied will disable

the Drive.

Page |

Remark:

t1: ENA must be ahead of DIR by at least 5

connected). See “

Connector P1 Configurations

t2: DIR must be ahead of PUL effective edge by 5

t3: Pulse width not less than 1.5

t4: Low level width not less than 1.5

. CAL

CULATION OF PULSE FREQUENCY

If need 60 RPM at 400

Then Frequency

TABLE :-(a)

Frequency With Different RPM At 400 Micro S

RPM

120

FREQUENCY(Hz)

400

800

TABLE :-( b)

Frequency With Different RPM at 800 Micro S

RPM

120

FREQUENCY(Hz)

800

1600

6. Connecting the Motor

Connections to 4-

lead Motors

4 lead motors are the least flexible but

inductance.

Connections to 6-

lead Motors

Like 8 lead stepping motors, 6 lead motors have two configurations available for high speed or high

torque operation. The higher speed configuration, o

of the motor’

s inductor windings. The higher torque configuration, or full coil, uses the full windings

of the phases.

Website:

E-mail id:-

support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

t1: ENA must be ahead of DIR by at least 5

s. Usually, ENA+ and

Connector P1 Configurations

”for more information.

t2: DIR must be ahead of PUL effective edge by 5

s to ensure correct direction;

t3: Pulse width not less than 1.5

µs;

t4: Low level width not less than 1.5

µs.

CULATION OF PULSE FREQUENCY

F = (RPM X MICRO STEP)/60 Hz

If need 60 RPM at 400

Micro Step (Half Step Setting)

Then Frequency

= (60X400)/60

= 400Hz

Frequency With Different RPM At 400 Micro S

tep

120

180

240

300

360

420

800

1200

1600

2000

2400

2800

Frequency With Different RPM at 800 Micro S

tep

If need 60 RPM at 800 Micro step

Then Frequency = (60X800)/60

= 800Hz

120

180

240

300

360

420

1600

2400

3200

4000

4800

5600

lead Motors

4 lead motors are the least flexible but

easiest to wire. Speed and torque will depend on winding

lead Motors

Like 8 lead stepping motors, 6 lead motors have two configurations available for high speed or high

torque operation. The higher speed configuration, o

r half coil, is so described because it uses one half

s inductor windings. The higher torque configuration, or full coil, uses the full windings

Website:

-www.bholanath.in

support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

s. Usually, ENA+ and

ENA- are NC (not

s to ensure correct direction;

F = (RPM X MICRO STEP)/60 Hz

420

480

540

2800

3200

3600

420

480

540

5600

6400

7200

easiest to wire. Speed and torque will depend on winding

Like 8 lead stepping motors, 6 lead motors have two configurations available for high speed or high

r half coil, is so described because it uses one half

s inductor windings. The higher torque configuration, or full coil, uses the full windings

Page |

Half Coil Configurations

As previously stated, the half coil configuration uses 50

lower inductance, hence, lower torque output. Like the parallel connection of 8 lead motor, the torque

output will be more stable at higher speeds. This

6-le

ad motor half coil (higher speed) connections

Full Coil Configurations

Lower speeds is desired. This configuration is also referred to as full chopper. In full coil mode, the

motors should be run at only 70% of thei

NOTE:

THE ABOVE CONFIGURATIONS IS FOR CONNECTI

MICROSTEP DRIVE AS PER APPLICATION/

MICROSTEP DRIVE.

Connections to 8-

lead Motors

8 lead motors offer

a high degree of flexibility to the system designer in that they may be

connected in series or parallel, thus satisfying a wide range of applications.

Series Connections

A series motor configuration would typically be used in applications where a higher to

at lower speeds is required. Because this configuration has the most inductance, the

performance will start to degrade at higher speeds. In series mode, the motors should also

be run at only 70% of their rated current to prevent

Parallel Connections

An 8 lead motor in a parallel configuration offers a more stable, but lower torque at lower speeds. But

because of the lower inductance, there will be higher torque at higher speeds.

Website:

E-mail id:-

support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

As previously stated, the half coil configuration uses 50

% of the motor phase windings. This gives

lower inductance, hence, lower torque output. Like the parallel connection of 8 lead motor, the torque

output will be more stable at higher speeds. This

configuration is also referred to as half chopper.

ad motor half coil (higher speed) connections

Lower speeds is desired. This configuration is also referred to as full chopper. In full coil mode, the

motors should be run at only 70% of thei

r rated current to prevent overheating.

lead motor full coil (higher torque) connections

THE ABOVE CONFIGURATIONS IS FOR CONNECTI

NG IN A BIPOLAR

MICROSTEP DRIVE AS PER APPLICATION/

NON-

AVAILABILITY OF A UNIPOLAR

lead Motors

a high degree of flexibility to the system designer in that they may be

connected in series or parallel, thus satisfying a wide range of applications.

A series motor configuration would typically be used in applications where a higher to

at lower speeds is required. Because this configuration has the most inductance, the

performance will start to degrade at higher speeds. In series mode, the motors should also

be run at only 70% of their rated current to prevent

overheating.

8-lead motor series connections

An 8 lead motor in a parallel configuration offers a more stable, but lower torque at lower speeds. But

because of the lower inductance, there will be higher torque at higher speeds.

FOR HALF COIL CONNECTION

CONNECT (A+)-

A Com & (B

A Com-(A-

) & B Com

FOR FULL

COIL CONNECTION

CONNECT (A+)-

LEAVE A Com & B Com OPEN

Website:

-www.bholanath.in

support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

% of the motor phase windings. This gives

lower inductance, hence, lower torque output. Like the parallel connection of 8 lead motor, the torque

configuration is also referred to as half chopper.

Lower speeds is desired. This configuration is also referred to as full chopper. In full coil mode, the

lead motor full coil (higher torque) connections

NG IN A BIPOLAR

AVAILABILITY OF A UNIPOLAR

a high degree of flexibility to the system designer in that they may be

connected in series or parallel, thus satisfying a wide range of applications.

A series motor configuration would typically be used in applications where a higher to

rque

at lower speeds is required. Because this configuration has the most inductance, the

performance will start to degrade at higher speeds. In series mode, the motors should also

An 8 lead motor in a parallel configuration offers a more stable, but lower torque at lower speeds. But

FOR HALF COIL CONNECTION

A Com & (B

+)- B Com/

) & B Com

-(B-)

COIL CONNECTION

-) & (B+)-(B-)

LEAVE A Com & B Com OPEN

Page |

7. Power Supply Selection

The Microstep Driver can match Large and small size stepping motors (from Nema size 17 to Nema

size 34

). To achieve good driving performances, it is important to sele

current properly. Supply voltage determines the high speed performance of the motor, while output

current determines the output torque of the driven motor (particularly at lower speed). Higher supply

voltage will allow higher m

otor speed to be achieved, at the price of more noise and heating. If the

motion speed requirement is low, it

improve reliability.

Regulated or Unregulated Power Supply

Both regulated an

d unregulated power supplies can be used to supply the driver. However,

unregulated power supplies are preferred due to their ability to withstand current surge. If regulated

power supplies (such as most switching supplies.) are indeed used, it is importan

current output rating to avoid problems like current clamp. On the other hand, if unregulated supply is

used, one may use a power supply of lower current rating than that of motor (typically 50%

motor current). The reason is that the driver draws current from the power supply capacitor of the

unregulated supply only during the ON duration, but not during the OFF duration. Therefore, the

average current withdrawn from power supply is consid

Multiple Drivers

It is recommended to have multiple drivers to share one power supply to reduce cost, if the

supply has enough capacity. To avoid cross interference,

supply input pins of the dri

vers. (Instead, please connect them to power supply separately

8. Troubleshooting

1. The status on light’s indication

RUN: green, normal work light.

ERROR

: red, failure light, the motor with phase short

protection.

NOTE:

TO CHECK IF DRIVE IS OK/NOT OK, CONNECT ONLY SUPPLY (AC /DC) VOLTAGE AND

GROUND TO THE MICROSTEP DRIVE AND CHECK THE LED INDICATOR IF IT SHOWS

GREEN THEN DRIVE IS OK AND IF THE LED INDICATOR SHOWS RED THEN DRIVE IS

NOT OK.

THIS TEST SHOULD

CARRIED AND MOTOR IS NOT RUNNING

Website:

E-mail id:-

support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

8-lead motor parallel connections

The Microstep Driver can match Large and small size stepping motors (from Nema size 17 to Nema

). To achieve good driving performances, it is important to sele

ct supply voltage and output

current properly. Supply voltage determines the high speed performance of the motor, while output

current determines the output torque of the driven motor (particularly at lower speed). Higher supply

otor speed to be achieved, at the price of more noise and heating. If the

motion speed requirement is low, it

’

s better to use lower supply voltage to decrease noise, heating and

Regulated or Unregulated Power Supply

d unregulated power supplies can be used to supply the driver. However,

unregulated power supplies are preferred due to their ability to withstand current surge. If regulated

power supplies (such as most switching supplies.) are indeed used, it is importan

current output rating to avoid problems like current clamp. On the other hand, if unregulated supply is

used, one may use a power supply of lower current rating than that of motor (typically 50%

motor current). The reason is that the driver draws current from the power supply capacitor of the

unregulated supply only during the ON duration, but not during the OFF duration. Therefore, the

average current withdrawn from power supply is consid

erably less than motor current

It is recommended to have multiple drivers to share one power supply to reduce cost, if the

supply has enough capacity. To avoid cross interference,

DO NOT daisy-

chain the power

vers. (Instead, please connect them to power supply separately

1. The status on light’s indication

RUN: green, normal work light.

: red, failure light, the motor with phase short

circuit, overvoltage and undervoltage

TO CHECK IF DRIVE IS OK/NOT OK, CONNECT ONLY SUPPLY (AC /DC) VOLTAGE AND

GROUND TO THE MICROSTEP DRIVE AND CHECK THE LED INDICATOR IF IT SHOWS

GREEN THEN DRIVE IS OK AND IF THE LED INDICATOR SHOWS RED THEN DRIVE IS

THIS TEST SHOULD

BE DONE

WHEN THE BELOW TROUBLE SHOOTING

CARRIED AND MOTOR IS NOT RUNNING

Website:

-www.bholanath.in

support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

The Microstep Driver can match Large and small size stepping motors (from Nema size 17 to Nema

ct supply voltage and output

current properly. Supply voltage determines the high speed performance of the motor, while output

current determines the output torque of the driven motor (particularly at lower speed). Higher supply

otor speed to be achieved, at the price of more noise and heating. If the

s better to use lower supply voltage to decrease noise, heating and

d unregulated power supplies can be used to supply the driver. However,

unregulated power supplies are preferred due to their ability to withstand current surge. If regulated

power supplies (such as most switching supplies.) are indeed used, it is importan

t to have large

current output rating to avoid problems like current clamp. On the other hand, if unregulated supply is

used, one may use a power supply of lower current rating than that of motor (typically 50%

～

～～

～

70% of

motor current). The reason is that the driver draws current from the power supply capacitor of the

unregulated supply only during the ON duration, but not during the OFF duration. Therefore, the

erably less than motor current

It is recommended to have multiple drivers to share one power supply to reduce cost, if the

chain the power

vers. (Instead, please connect them to power supply separately

circuit, overvoltage and undervoltage

TO CHECK IF DRIVE IS OK/NOT OK, CONNECT ONLY SUPPLY (AC /DC) VOLTAGE AND

GROUND TO THE MICROSTEP DRIVE AND CHECK THE LED INDICATOR IF IT SHOWS

GREEN THEN DRIVE IS OK AND IF THE LED INDICATOR SHOWS RED THEN DRIVE IS

WHEN THE BELOW TROUBLE SHOOTING

Website:-www.bholanath.in

E-mail id:-support@bholanath.in

BHOLANATH PRECISION ENGINEERING PVT. LTD.

Page |

2. Troubles

Problems

Possible cause

Solutions

No power supply Check the power supply

Motor is not

No control signal Check the control signal

rotating

The driver is disabled

Don’t connected the enable signal

or enable the driver

Supply voltage is too high or

Check the supply voltage

too low

ALM lights

Motor line short-circuit

Check motor lines eliminate the

short-circuit

Motor line wrong connect

Check the motor wiring

Motor or drive failure

Replace the motor or drive

Motor rotates in

Motor phases connected in

Reverse the phases line

the wrong

reverse

direction

Wrong I/p direction signal Change direction setting

Motor line break

Change the phases are connected

Inaccurate

The Micro steps set incorrectly.

Set the correct segments

The motor load is too heavy. Increasing the current

Position

Control signal is interfered Eliminate interference

Power supply voltage too low

Increasing the supply voltage

Motor Stalled

Accelerating time is too short.

Extend the acceleration time

Current setting is too small Increasing the current

Motor torque is too small

Replace the motor

Inhaltsverzeichnis

Andere Bholanath Steuereinheit Handbücher

Bholanath

Bholanath BH-SMART-6A Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung