Bibene D3-1 Bedienungsanleitung

D3-1 Two-way Digital Keypad Alarm System

User Manual

Foreword

I. Introduction

Thanks for purchasing BIBENE D3-1 alarm system.

Please read this user manual carefully before use, we will

update this manual on a regular basis in accordance with

the addition or upgrade of the product features. If you

need any assistance, please contact our support team,

we will contact you within 24 hours.

Customer Service Email Address:

lhxing@hotmail.com

Warm Tip:

Customers who have purchased before: Can start and

focus on chapter 5(Quick Start by Easy Testing) &

chapter 6 ( Zone Features Introduction)

Freshman: Please follow the step start from chapter 1

Table of Contents

1.Product Features-------------------------------------

2. Operating Principle---------------------------------

3.Check Kit Accessory--------------------------------

4. Button Introduction --------------------------------

4.1 Main panel Button--------------------------------

4.1.1 ARM:---------------------------------------------

4.1.2 DISARM: ----------------------------------------

4.1.3 Away Home Mode------------------------------

4.1.4 At Home Mode:---------------------------------

4.1.5 Chime/alarm Switch---------------------------

4.2 Remote Control Button--------------------------

4.3 PIR Motion Sensor Button----------------------

4.4 Door/window Sensor ---------------------------

5. Quick Start by Easy Testing-----------------------

5.1 Check Zone for Door/Window Sensor---------

6. Zone Features Introduction-----------------------

6.1 Features of 4 Modes Zones-------------------

6.2 List of zone feature setting:---------------------

6.3 Zone Features Setting---------------------------

7.Expand more accessory----------------------------

7.1 Add Remote Control------------------------------

7.2 Delete Remote Control--------------------------

7.3 Add Door/window Sensors----------------------

7.4 Delete Door/window Sensors------------------

7.5 Add PIR Motion Sensor -------------------------

7.6 Delete PIR Motion Sensors---------------------

8. Installation--------------------------------------------

8.1 Main Panel Installation-------------------------

8.2 Door/window Sensor installation--------------

8.3 PIR Motion Sensor installation----------------

9. Change Dis-arm Password -----------------------

10.Low Battery Prompt--------------------------------

11.Restore Factory Setting---------------------------

12. DIY Solution Q & A---------------------------------

12.1 Tommy’s Ofﬁce---------------------------------

12.2 Jenny’s Cute Cafe------------------------------

12.3 Molly’s Home------------------------------------

13.Product Speciﬁcation-----------------------------

13.1 Main Panel---------------------------------------

13.2 PIR Motion Sensor:-----------------------------

13.3 Door / Window Sensor:-------------------------

13.4 Wireless Remote Control:---------------------

14.Terms of Warranty ---------------------------------

1. Product Features

1)Main Panel works as stand alone alarm

2)Easy One-button Operation

3)4 zones for DIY home security system

4 ) W h e n t r i g g e r a l a r m s , t h e L E D i n d i c a t o r o f

correspondent zone will ﬂash to warn you the exact

alarm area

5)More safer to disarm by 4-Digital password on keypad

6)Away & home modes to set arming delay/arming

7)Support to put magnet on the left/right side of the main

panel

8)Chime/alarm switch for ring tone selection

9)Stylish design ﬁts home decoration

10)Expandable to pair up to 10 remotes, and each zone

could add up to 10 sensors.

2. Operating Principle

Professional DIY Security Alarm System:

Built-in Magnetic Contact Sensor & PIR motion sensor

which can detect any forceful break-in and activate the

alarm to deter potential intruders and alerts neighbors.

The LED indicator of corresponding alarm zone ﬂashes to

warn you the exact alarm area too.

3. Check Kit Accessory

D3-1 Kit includes:

1x Main Panel

4x Door/window Sensors

1x Remote Control

1x User Manual

All battery and Adhesive tape

4. Button Introduction

4.1 Main panel Button

4.1.1 ARM:

Short Press on button on panel, the 4 LED indicators

of the panel will ﬂash one time and beep once.

1 2

4.1.2 DISARM:

Enter the default password 1234 on keypad, the 4 LED

indicator of Panel will ﬂash twice and beep twice. (3 beep

sounds indicates entering wrong password)

4.1.3 Away Home Mode: Arm delay & Alarm delay for

30seconds (Only work for Main panel)

-When you arm, the Main panel indicator will ﬂash every

second for 30seconds,then the main panel will emit a

beep sound to notice you arm successfully. And when

trigger alarm, the main panel will also delay 30seconds to

alarm. This mode is great for you to arm when you are

about to leave home without any alarms to annoy you.

4.1.4 At Home Mode: Arm directly and alarm directly

when trigger alarm.

(Only work for Main panel)

4.1.5 Chime/alarm Switch (Only work for main panel)

Choose Chime or alarm sound for main panel.

4.2 Remote Control Button

3 4

Ar m Del a y (A f te r p re s s, w il l arm a ft e r

30seconds)

Disarm directly after press

Arm Directly after press

SOS: Alarm directly after press(4 LED indicator

ﬂash)

4.3 PIR Motion Sensor Button Instruction

4.4 Door/window Sensor Instruction

5. Quick Start by Easy Testing

We have paired all the sensors to main panel already.

Just do a easy testing to check the corresponding Zone

for each PIR motion or Door sensor. Then you can install

& DIY different features for each Zone for your home

security system.

5.1 Check Zone for Door/Window Sensor :

1) Power on the Main panel: The battery are already

loaded with a ﬁlm, Just take off the ﬁlm to power on the

main panel.

2)Put the transmitter tightly close to magnet (Make sure

the triangle marks are close to each other)

5 6

3) Press on main panel to ARM.

4) Separate the transmitter and magnet over than 2CM, it

will trigger alarm

5) W he n a la r m is t r ig g er e d, t he LE D ind i ca t or o f

corresponding alarm zone will ﬂash to make you quick

distinguish

6. Zone Features Introduction

6.1 Features of 4 Mode Zones

Please Note:

Zone Features & Setting is only applicable to door sensor

or PIR motion Accessory, not applicable to main panel.

Ordinary Zone:

When trigger alarm,the main panel will emit siren sound

on the status of Arming, NO alarm sound when under

disarming status.

Doorbell Zone:

When trigger alarm, the main panel will always emit

doorbell sound no matter under arm or disarm status.

Emergency Zone:

When trigger alarm, the main panel will emit siren sound

no matter under arm or disarm status.

Welcome Zone:

When trigger alarm, the main panel will emit siren sound

on arming status,and emit doorbell sound on disarming

status.

6.2 List of zone feature setting:

7 8

Zone

Zone1

Zone2

Zone3

Zone4

Method Prompt Zone Mode Arm Delay

or not Done

Long press

& [1]

simultaneously

LED indicator

of Zone 1 keeps

ﬂashing

6.3 Zone Features Setting

1) Long press on button and digit [1] on the main

panel simultaneously, the LED indicator of zone 1 will

keep ﬂashing, that means entering the setting process of

the zone1 mode.

2) Then short Press the corresponding digital number

according to the mode you need ( Ordinary Mode is 1,

Emergency mode is 2, Doorbell mode is 3, Welcome

Mode is 4)

3) Then short press the corresponding digital number to

choose arm delay or not ( press 1 for No arming delay ,

press 2 for arm delay for 30seconds )

4)After above setting done, the main panel will emit a

long beep sound. Means Setting Done.

1. Ordinary

2. Emergency

3. Doorbell

Welcome

1.No Arming

delay

2.Arm delay

for30seconds

Long

Beep

sound

indicates

set

success

fully.

Then

short

press to

quit

setting.

Long press

& [2]

simultaneously

Long press

& [3]

simultaneously

Long press

& [4]

simultaneously

LED indicator

of Zone 2 keeps

ﬂashing

LED indicator

of Zone 3 keeps

ﬂashing

LED indicator

of Zone 4 keeps

ﬂashing

1. Ordinary

2. Emergency

3. Doorbell

Welcome

1. Ordinary

2. Emergency

3. Doorbell

Welcome

1. Ordinary

2. Emergency

3. Doorbell

Welcome

1.No Arming

delay

2.Arm delay

for30seconds

1.No Arming

delay

2.Arm delay

for30seconds

1.No Arming

delay

2.Arm delay

for30seconds

5) Finally press button to quit setting process.Done.

Note:

Same steps to set features for zone 2, zone 3, zone 4.

7.Expand more accessory

Please Note:

-It only allows to add/delete sensors on status of

Disarming. Otherwise it will emit 3 beep prompt

tone to notice you incorrect operation.

-During learning, the short press or no operation will

cause quitting learning status.

7.1 Add Remote Control

1) Long press the button on main panel, the 4 LED

indicator light on, means the main panel is under learning

status.

2) Press any key on remote control.The main panel LED

indicator ﬂash 2times with 2 beep sound!

3) Press on main panel to quit setting. Done!

Note:

-If LED indicator ﬂashes only 1time & with 1 beep sound,

means this remote control repeated.

- I f L E D i n d i c a t o r ﬂ a s h e s 3 t i m e s & w i t h 3 b e e p

sound,means this remote control are already added to

limitation(10pcs)

-The main panel can expand remote control up to

10 pcs.W hen main panel is on learni ng status ,just

continue to press any button on remote control 2,3...10.

9 10

7.2 Delete Remote Control

1) Long press the button on main panel, till the 4 LED

indicator light on, indicates the main panel is under

learning status.

2) Release pressing.

3) Again long press the button on main panel, the 4

LED indicator ﬂash 4times & with 4 Beep sounds.Done!

7.3 Add Door/window Sensors

Add Door/Window Sensor for Zone 1

1) Long press 【1】 button, No.1 LED indicator of main

panel is on, indicates the main panel is under learning

status.

2) Put the magnet tightly close to transmitter ﬁrstly,then

move the magnet away (at least 2cm far away), then put it

close to transmitter again.The No.1 LED indicator will

ﬂ a s h 2 t i m e & d o o r s e n s o r e m i t s 2 t i m e s b e e p

sound,means bi n d i n g s u c c e s sf u l l y.(If only 1 beep

so u n d,indicat e s lea r ning repeated; if 3t i mes be ep

sounds,means sensors are added to limitation 10pcs

already)

3) Press Press button to quit setting. Done.

Tips: Same step applicable to set forzone2,zone3,zone4.

7.4 Delete Door/window Sensors

1) Long press 【1】 button on main panel, No.1 LED

indicator of main panel will be on, means the main panel

is under learning status.

2) Release press

3) Again long Press 【1】 button again, the main panel

indicator will ﬂash 4times & with 4times beep sounds.All

the sensors in Zone 1 are deleted.

Tips: All above steps are applies for ZONE 2,ZONE 3,

ZONE4.

11 12

7.5 Add PIR Motion Sensor

1)Long press 【1】 button, No.1 LED indicator of main

panel is on, indicates the main panel is under learning

status.

2) Place PIR motion detection lens face to you .The No.1

LED indicator will ﬂash 2time & door sensor emits 2times

beep sound,means binding successfully.If only 1 beep

so u n d,indicat e s lea r ning repeated; if 3t i mes be ep

sounds,means sensors are added to limitation 10pcs

already (For PIR motion detector adding,just put PIR

detector face to you,it will binding successfully.)

3) Press Press button to quit setting. Done.

7.6 Delete PIR Motion Sensors

1) Long press 【1】 button on main panel, No.1 LED

indicator of main panel will be on, means the main panel

is under learning status.

2) Release press

3) Again long Press 【1】 button again, the main panel

indicator will ﬂash 4times & with 4times beep sounds.All

the sensors in Zone 1 are deleted.

Tips: All above steps are applies for ZONE 2,ZONE 3,

ZONE4.

8. Installation

Please Note:

-Avoid installing outside where easily to be destroyed

-Avoid installing closed to magnetic sources,such as

heaters, air conditioner,microwave oven which may

cause false triggering.

8.1 Main Panel Installation

Make sure the contact works properly before installing it.

1) Main panel supports the magnet to be placed both the

left and right side of main panel.Make sure the main

panel is close to magnet.

2) Paste the main panel and magnet separately on doors

or windows or any other open/close places with provided

double-sided tapes.

3) Done! Once the transmitter and magnet is separated

around 2cm by intruder ,the LED light in transmitter will

be on in Red. Alarm will be activated.

8.2 Door/window Sensor installation

Make sure the contact works properly before installing it.

4) There are triangle marks on the side of the transmitter

13 14

Inhaltsverzeichnis

Andere Bibene Sicherheitssystem Handbücher

Bibene

Bibene WP7 Bedienungsanleitung

Bibene

Bibene DW9 Bedienungsanleitung

Bibene

Bibene W20 Bedienungsanleitung

Bibene

Bibene N9 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung