Biesemeyer T-SQUARE BC30 Bedienungsanleitung

INSTRUCTION MANUAL

To learn more about BIESEMEYER MANUFACTURING

visit our web site at: www.biesemeyer.com.

For Parts, Service, Warranty or other assistance,

please call 1-800-782-1831

PART NO. 1352432

REVISED 03-01-07

BIESEMEYER® T-SQUARE®

Commercial Fence System

(Model BC30)

(Model BC30W)

(Model BC50)

(Model BC50W)

INTRODUCTION

The BIESEMEYER®T-SQUARE®Commercial fence system includes the fence assembly, front rail, rear rail

and front guide tube along with the mounting hardware for assembling the fence system to many

different types of table saws. Depending on the model ordered, an accessory leg kit may also be

included. An accessory right extension table and support legs are also required. The right extension

table may be purchased seperately or may be constructed by following the diagram in this manual. If

the leg kit is not included with the fence, it may be ordered seperately as well. IMPORTANT: The

BIESEMEYER®T-SQUARE®Commercial fence system is designed to be used only with a supporting

extension table and leg kit.

UNPACKING

Carefully unpack the BIESEMEYER®T-SQUARE®Commercial fence system from the shipping cartons. Fig. 1

illustrates all the items supplied with the guide set. Fig. 2 illustrates all the items supplied in the fence

box and the accessory right hand extension table. Support legs shown are only provided with Part No.

78-200. NOTE: If you did not purchase the right extension table for use with your T-SQUARE®fence

system, refer to the next section titled “Constructing Extension Table” for information on constructing an

extension table.

1. Guide Tube

2. Front Rail

3. Rear Rail

Fig. 1

1. T-Square®Fence

2. Support Leg (2)

3. Leveling Foot (2)

4. 3/8-16 Hex Nut (2)

5. #8 x 5/8” Pan HD Screw (12)

6. #10-32 X 3/8” RND HD Screw (2)

7. Flat Washer (2)

8. Hairline Pointer

9. Knob

For Attaching Front Rail to Delta Unisaw/Contractor

Saw/Hybrid Saw

10. 5/16-18 x 1-1/4” Flat HD Screw (2)

11. 3/8 Lock Washer (2)

12. 3/8 Flat Washer (2)

13. 5/16-18 Hex Nut (2)

For Attaching Extension Table (All Saws)

18. 1/4-20 x 1-1/2” Flat HD Screw (14)

19. Fender Washer (14)

20. 1/4-20 Hex Nut (14)

For Attaching Front & Rear Rail to Non Delta Saws

21. 1/4-20 x 1-1/4” Flat HD Screw (10)

22. 1/4” Lockwasher (10)

23. 1/4” Flat Washer (10)

24. 1/4-20 Hex Nut (10)

For Attaching Guide Tube to Front Rail

25. 1/4-20 X 1/2” Hex HD Screw (7)

26. 1/4” Lock Washer (7)

27. Template

For Attaching Rear Rail to Delta Hybrid Saw and Left-Tilt

Contractor’s Saw ONLY

28. 8MM x 1” Hex HD Screw (2)

29. 8MM Lock Washer (2)

30. 8MM Flatwasher (2)

18 19 20 21 22 23 24

29 30

For Attaching Rear Rail to Delta Unisaw/Right-tilt

Contractors Saw

14. 3/8-24 x 1-1/4” Hex HD Screw (2)

15. 3/8 Lock Washer (2)

16. 3/8 Flat Washer (2)

17. 3/8-24 Hex Nut (2)

Fig. 2

CONSTRUCTING EXTENSION TABLE

ASSEMBLY (DELTA SAWS ONLY)

FOR ALL OTHER SAWS, PROCEED

DIRECTLY TO PAGE 7, STEP 1.

DISCONNECT THE SAW FROM

THE POWER SOURCE!

FRONT RAIL TO SAW

1. Assemble front rail (A) Fig. 5 to the front edge of the saw

table using the two 5/16-18 x 1-1/4” long flat head Phillips

screw, flat washer, 3/8” lock washer and 5/16-18” hex nut (B)

supplied. Screws are inserted throught the two larger counter-

sunk holes in the front rail and into the two holes in the front of

the saw table and fastened with the flat washer, lock washer

and hex nut. IMPORTANT: Do not tighten front rail mounting

hardware at this time.

FOR DELTA CONTRACTORS & HYBRID SAWS ONLY

Hang the on/off switch from the front rail mounting bolt on the

left side of the saw, as shown in Fig. 6, before putting on the

flat washer, lock washer and hex nut.

2. Using template (C) Figs. 5 & 7, Check and adjust the front

rail on both sides of the saw blade as shown, to make sure the

rail is parallel with the table surface. The horizontal portion of

the rail should be down from the top of the table surface

2-27/32”. Tighten the front rail mounting hardware when

you are certain the rail is set at the proper depth.

Fig. 4

Fig. 5

Fig. 6

REAR RAIL FOR DELTA SAWS

NOTE: Do not use template to set rear rail.

3.Align the two non-countersunk holes in the rear rail with the

two holes in the rear edge of the saw table. The two cutouts in

the rear rail need to be below the bottom of the two miter slots

in the saw table. Fasten rear rail to the saw as follows:

For Delta Unisaw Thread the two 3/8-24 x 1-1/4” long hex

head screw, lock washer and flat washer (D), supplied, Fig. 8,

through the two holes in the rail and into the two threaded

holes in the saw table.

For Right-tilting Delta Contractor’s Saws Fasten rail to the

saw using the two 3/8-24 x 1-1/4” hex head screws, lock

washers, flat washers and hex nuts (E) supplied, Fig. 9. The

lock washer, flat washer and hex nut will be on the inside edge

of the saw table.

For Delta Hybrid Saw and Left-tilting Contractor’s Saw

Fasten rail to the saw using the two 8MM x 1” long hex head

screw, 8MM lock washer and 8MM flat washer supplied, Fig 8,

through the two holes in the rail and into the two threaded

holes in the saw table.

4. After fastening the rear rail to the saw table, tilt the saw

blade to make certain there is no interference between the

guard splitter and the rear rail. If there is, it will be necessary

to enlarge the cut-out (F), Fig. 9, in the rear rail.

TABLE LEGS TO TABLE BOARD

IMPORTANT: If your saw fence system will be used with a

mobile base underneath the saw base and table legs, the

position of the legs will have to be changed to fit the

mobile base extension.

5. Assemble the 3/8” jam nut (G) onto leveling screw (H).

Thread leveling screw into bottom of support leg. Fig. 10

illustratesthefootlevelingassemblyonthetableleg.Assemble

the remaing foot assembly to the other leg in the same

manner. NOTE: Height adjustment will be made later.

Fig. 7

Fig. 8

Fig. 9

Fig. 10

6. Lay the table upside down on the floor or on a bench.

7. Position the table leg (I) to the closed in corner of the extension

table (J) as shown in Fig. 11.

8. Attach the table leg to the table board with six 5/8” long wood

screws (K). Repeat this process for the remaining leg.

IMPORTANT: If your saw fence system will be used with a

mobile base underneath the saw base and table legs, the

position of the legs will have to be changed to fit the mobile

base extension.

NOTE: Table shown installed on a Unisaw without the cast iron

wing. If your saw has a cast iron extension wing on the right

hand side, it is not necessary to remove the wing. The

extension table can extend past the rails and tube.

9. Place table assembly (L) Fig. 12, in position between the two

rails, as shown. Make sure end of table is flush against saw table

(M). Using a straight edge make sure table (L) is in the same plane

and level with saw table (M). Lightly tap up or down and adjust leg

leveling screws. When you are certain table (L) is level and in the

same plane with saw table (M) tighten bar clamp (P) to hold

everything in position. Then drill 1/4” holes through the front and

rear of the extension table using holes (Q) provided in rails as a

template. NOTE: Number of holes (Q) in the front and rear rails will

vary depending on the length of the rails you purchased.

10.After the holes have been drilled in the edge of the front and rear

extension table board, fasten both front and rear rail to table using

the 1/4-20 x 1-1/2” flat head Phillips screws, 1-1/4” O.D. flat

washers and hex nuts (R).

11. Lay the guide tube (B) Fig. 14, on the saw table as shown, and

line up the threaded holes (S) on the bottom of guide tube with the

through holes (T) on the front rail. NOTE: The guide tube should

extend past the rail 6” on each end.

12. Position the guide tube (B) on the front rail and fasten the guide

tube to the rail using the 1/4-20 x 1/2” long hex head screws and

lock washers. NOTE: Where there are two holes 2-1/2” apart, use

only one of the two holes.

PROCEED TO STEP ONE ON PAGE 9

Fig. 11

Fig. 12

Fig. 13

Fig. 14

ASSEMBLY (FOR ALL OTHER SAWS)

DISCONNECT THE SAW FROM THE POWER

SOURCE!

ASSEMBLE FRONT RAIL

1. Raise saw blade (A) Fig. 15. Place a straight edge (B)

against the right side of saw blade extending out over the

front of the saw as shown. Position front rail (C) against

the edge of saw table and lightly clamp in place using bar

clamps (D).Align notch (E) in front rail (C) with the straight

edge (B) as shown. NOTE: Any portion of the notch

needs to align with the straight edge. Final

calibration will be explained later.

2. Using template (F) Fig. 16, check and adjust the front

rail at both sides of saw table, to make sure the horizontal

portion of front rail (C) is parallel with the table top and

then tighten bar clamps. The rail should be down from

the top of the table 2-27/32”.

3. When you are certain front rail (C) is level with the table

surface, drill four 1/4” through holes into the saw table

using the 1/4” counter sunk holes in the front rail as a

template. IMPORTANT: Before drilling, check to make

certain there is no interferance such as casting ribs

behind front edge of saw table.

4. Fasten front rail (C) to saw table using the four 1/4-20 x

1-1/4” long flat head screws, flat washers, lock washers

and hex nuts supplied.

ASSEMBLE REAR RAIL

5. Clamp rear rail (G) Fig. 17, to back of saw table using

bar clamps making certain notch (E) in rail is aligned with

saw blade (A) as shown, using straight edge (B). Make

sure the two cutouts in the rail are below the bottom of the

miter slots in the saw table.

6. Check to make certain there are no interferance such

as casting ribs behind the rear edge of the saw table and

drill a minimum of two through holes into the saw table

using the countersunk holes as a template. Fasten rear

rail to saw table using the 1/4-20 x 1-1/4” long flat head

screws, flat washers, lock washers and hex nuts supplied.

IMPORTANT: If there is no room in rear edge of the

table to drill through holes, it will be necessary to drill

#7 holes and tap holes with a 1/4-20 tap.

7.After fastening the rear rail to the saw table, tilt the saw

blade to make certain there is no interferance between

the saw guard and the rear rail. If there is, it will be

necessary to enlarge the cut-out (H) Fig. 17, in the rear

rail.

EXTENSION TABLE & SUPPORT LEGS

8. Assemble the 3/8” jam nut (I) onto leveling screw (J).

Thread leveling screw into foot adapter. Fig. 18 illustrates

the foot leveling assembly on the table leg.Assemble the

remaining foot assembly to the other leg in the same

manner. NOTE: Height adjustments will be made later.

Fig. 16

Fig. 15

Fig. 17

Fig. 18

IMPORTANT: If your saw fence system will be used

with a mobile base underneath the saw base and table

legs, the position of the legs will have to be changed

to fit the mobile base extension.

9.Laytheextension tableupsidedown on a floor or bench.

10. Position table leg (K) to the closed in corner of the

extension table (L), as shown in Fig. 19.

11. Attach the table leg (K) to the table board (L) with six

5/8” long wood screws (M). Repeat this process for the

remaining leg.

IMPORTANT: If your saw fence system will be used

with a mobile base underneath the saw base and table

legs, the position of the legs will have to be changed

to fit the mobile base extension.

12. Place table assembly (L) in position between the front

and rear rail, as shown in Fig. 20. Make sure end of table

is flush against saw table and using a bar clamp, snug up

endsofrailsto hold tableinposition.Using a straight edge,

(N), make certain table is in the same plane and level with

sawtable.Adjustleveling screwsinbottom of support legs

to accomplish this. When you are certain table is level

and in the same plane as the saw table, tighten bar clamp

to hold everything in position. Then drill 1/4” through holes

through the front and rear table frame using holes (O) in

the rail as a template. The number of holes to drill will

depend on the length of the rails.

13. After the holes have been drilled in the front and rear

table frame, fasten both front and rear rail to table Fig. 21

using the 1/4-20 x 1-1/2” long flat head screws, fender

washers and hex nuts (P) provided.

14. Lay guide tube (Q) Fig. 22, on saw table as shown,

and line up the threaded holes (R) in bottom of guide tube

with through holes (S) in the front rail. Guide tube will

extend 6” past the rail at both ends.

15. Lay guide tube on front rail and fasten the guide tube

to the front rail using the 1/4-20 x 1/2” long hex screws

and lockwashers provided. NOTE: Where there are two

holes 2-1/2” apart, use only one of the holes.

Fig. 19

Fig. 20

Fig.21

Fig. 22

ASSEMBLY (FOR ALL SAWS)

1. Attach knob (A) Fig. 23 to locking handle (B). Knob is

screwed onto threads of locking handle.

2. Align fence side (C) Fig. 24, with the miter slot on the

table saw and lock fence in position. Using a measuring

tape (D), measure the distance from the saw blade to the

fence side.

3. WITHOUT MOVING THE FENCE, attach hairline

pointer (E), Fig. 25 to fence crossarm (F) using two

#10-32 x 3/8” round head screws and flat washers (G).

Screws go through the slotted holes in the pointer and

into the threaded holes (H) in the crossarm. Using the

measurement from Step 2, align the black line in the

pointer to the same measurement on the guide tube tape

and securely tighten screws.

IMPORTANT: CHECK TO MAKE CERTAIN THAT THE

MITER GAGE SLOTS IN THE SAW TABLE ARE

PARALLEL WITH THE SAW BLADE. CHECK WITH THE

INSTALLATION MANUAL THAT CAME WITH YOUR

SAW FOR INSTRUCTIONS.

4. The fence (C) Fig. 26, must be adjusted so it is parallel

to the miter gage slot. Slide the fence until the bottom

edge is in line with the edge of the miter gage slot as

shown and push down on locking handle (B). Check to

see if the fence (C) is aligned with the miter slot the entire

length of the table. If an adjustment is needed, lift fence

loosen adjusting screws (J) or (K), using a 3/16” Allen

wrench (N), not included. Replace the fence on the guide

tube and check again. Repeat this adjustment until you

are certain the fence is parallel to the miter gage slot.

NOTE: Very little movement of the adjusting screws

is necessary to adjust the fence.

Fig. 23

Fig. 24

Fig. 25

Fig. 26

5. When the fence locking handle (B) Fig. 28, is pushed

to the down position, the fence assembly (C) should be

completely clamped to the guide tube. If the fence

assembly (C) is not completely clamped to the guide tube

when the handle is pushed down, as shown, lift up handle

(B) and raise fence off the guide tube as shown in Fig. 27.

Slightly tighten the two adjusting screws (J) and (K) (if the

fence is too loose) or loosen (if the fence is too tight),

using a 3/16” Allen wrench (N), not supplied. NOTE:

Screws (J) and (K) should be tightened or loosend an

equal amount. Replace the fence back on the guide tube

and recheck to see if the fence assembly is completely

tightened to the guide tube with the locking handle (B)

pushed down. Adjust further if necessary.

IMPORTANT: AFTER ADJUSTING THE FENCE

CLAMPING ACTION, RECHECK TO SEE THAT THE

FENCE IS STILL PARALLEL TO THE MITER GAGE

SLOT AND ADJUST AS NECESSARY.

6. When clamping the fence assembly (C) to the guide

tube, make certain the camfoot (P), Fig. 29, is hanging

down and against the locking handle (B), and not caught

on top of the guide tube.

7. To move the fence along the guide tube, simply lift up

the locking handle (B) Fig. 30, as shown, slide the fence

to the desired position on the guide, and push down

locking handle (B) Fig. 28 as shown, to lock in position.

NOTE:Amagnet(R)Fig.28, is provided to hold the handle

in the up position when moving the fence.

Fig. 27

Fig. 28

Fig. 29

Fig. 30

Dieses Handbuch passt für folgende Modelle

Andere Biesemeyer Zäune & Tore Handbücher

Biesemeyer

Biesemeyer T-Square 2 Bedienungsanleitung

Beliebte Zäune & Tore Handbücher anderer Marken

Casanoov

Casanoov KIT-000045 Bedienungsanleitung

Heras

Heras SHB21 Bedienungsanleitung

Casanoov

Casanoov VOGEL 350C140 Bedienungsanleitung

DITEC

DITEC Silver 1B/40B Handbuch

Casanoov

Casanoov EIGER 350C140 Bedienungsanleitung

Olli

Olli Lister WZG 180B Bedienungsanleitung

WamBam

WamBam BL19042 Bedienungsanleitung

Wisniowski

Wisniowski MakroPro 100 Bedienungsanleitung

Zippity

Zippity WASHINGTON Bedienungsanleitung

Roger Technology

Roger Technology LT338 Bedienungsanleitung

CAI

CAI SG-60-PCY Bedienungsanleitung

Hahn

Hahn hanit Betriebsanleitung

Oxgard

Oxgard K-14 Bedienungsanleitung

patura

patura P4500 Bedienungsanleitung

Betafence

Betafence HoriZen Prime Bedienungsanleitung

VIEWRAIL

VIEWRAIL Vedera Bedienungsanleitung

Alvarado

Alvarado CSG Bedienungsanleitung

RTL

RTL INSTABOOM LITE Bedienungsanleitung