Bigassfans HAIKU Bedienungsanleitung

HAIKU®by BIG ASS FANS

WARNING: Ensure power is disconnected at the fuse/breaker distribution panel before installing or

servicing the wall control and fan!

CAUTION: Installation must be completed in strict conformance with local building and electrical

codes.

WARNING: If installing the fan in Australia, qualiﬁed licensed professionals should perform all

installation work.

Review the safety guidelines in the complete Haiku® Installation Guide. If you have questions about any

aspect of the installation process, contact Haiku Technical Service at www.haikufan.com for assistance.

PARTS AND HARDWARE

If you are missing any parts or hardware required for the installation of your Haiku wall control, contact Haiku

Technical Service. Note: Drawings are not to scale.

Wall control (2) #6-32 x 7/8” screw RF board Antenna retainer

Note: If your wall control kit does not include a wall plate, Big Ass Fans recommends using a Decora® wall

plate. Other brands may not be compatible. The junction box and wire connectors are customer supplied.

INSTALLATION

While installing the fan(s) according to the complete Haiku Installation Guide, follow the steps below to

install the Haiku wall control and RF board. It is possible to link up to four (4) Haiku fans to a single controller

to simultaneously control airﬂow, lights, and special features. If installing linked fans, the ﬁrst fan must be

located within 20 ft (6 m) of the wall controller. Successive fans must be within 20 ft (6 m) of each other and

with no physical obstructions.

Step 1. Set the wall control address

a) Remove the rubber covering from the back of the wall control. Locate the

DIP switch and rotary switch. See bottom right of this page for the switch

location on the wall control.

b) Toggle DIP switch 1 either on or o, and then turn the rotary switch to one

of sixteen channels. Use a small screwdriver or similar tool to turn the

rotary switch. Together DIP switch 1 and the rotary switch allow 32 unique frequency settings (two sets of

16) to prevent interference between multiple wall controls.

c) Set DIP switches 2–4 as shown below. Make sure switch 3 is o. Settings for switches 2 and 4 depend on

whether the wall control will control a single fan or multiple fans, and whether any of the fans has a light.

HAIKU®WALL CONTROL KIT

4321

Single fan Multiple fans

Fan(s) with light

For multiple fans, this setting applies

if any of the fans has a light

Fan(s) without light

HAIKU®by BIG ASS FANS

HAIKU WALL CONTROL (CONT.)

Step 2. Set the RF board address

CAUTION: Do not adjust the DIP switch settings on the fan’s circuit board! Adjust only the

DIP switches on the RF board(s) that will be plugged into the fan(s).

1. Locate the DIP switch and rotary switch on the RF board(s).

2. Set the rotary switch and DIP switch 1 to match the setting on

the wall control.

3. Set DIP switches 2–4 as shown below. Make sure switch 3 is on. Settings for switches 2 and 4 depend on the fan’s

position in the control sequence and whether the fan is alone or is linked to another fan.

Step 3. Remove lower cover

Remove the lower cover from the fan as shown below. On Haiku®Bamboo fans, pry o the cover. On Haiku®

composite fans, twist the lower cover counterclockwise to remove it.

Haiku®Bamboo

Lower Cover

Haiku®

Lower Cover

4321

Single fan Multiple fans

First fan (fan closest to wall control) Subsequent linked fan(s)

HAIKU®by BIG ASS FANS

HAIKU WALL CONTROL (CONT.)

Step 4. Install RF board

CAUTION: Do not touch the fan electronics during installation unless necessary!

CAUTION: Do not adjust the DIP switch settings on the fan’s circuit board! Adjust only the

DIP switches on the RF board(s) that will be plugged into the fan(s).

WARNING: Ensure power is disconnected at the fuse/breaker before installing the wall control and

the fan!

Install the RF board in the fan circuit board as shown below. If linking multiple fans, install an RF board in

each fan circuit board.

If the fan’s circuit board has one row of female connectors (blue), install the lower set of six (6) RF board

prongs into the circuit board. If the fan’s circuit board has two (2) rows of female connectors (black), install all

twelve (12) RF board prongs into the circuit board.

Step 5. Install antenna retainer

Secure the antenna to the antenna retainer, and then peel the adhesive backing o the retainer.

Attach the sticky side of the retainer to the inner side of the hub wall as shown. Make sure the antenna is

straight and snug in the retainer, and that the retainer is far enough inside the hub that the lower cover will

not rub against it. Reinstall the lower cover.

Underside of Fan Hub

RF Board

Female

connectors

(two rows)

Prongs

Do NOT

adjust these

DIP switches!

Underside of Fan Hub

Antenna

Retainer

If the fan does not respond to commands from the

wall control, adjust the position of the antenna in

the retainer until the fan responds.

tip! Hub Wall

HAIKU®by BIG ASS FANS

Step 6. Wire the wall control

WARNING: Ensure power is disconnected at the fuse/breaker distribution panel before wiring the

wall control and the fan!

CAUTION: Do not use the fan with a dimmer switch.

While supporting the wall control, connect the wires with wire connectors as shown below. Switch leg wiring

is recommended by Big Ass Fans. If switch leg wiring is not possible, secure the end of the red wire with a

wire connector.

HAIKU WALL CONTROL (CONT.)

Wire color chart

Wall Control Wire Color

North America

Australia*

AC Line (L1)

Black

Red

AC Neutral (L2/N)

White

Blue

PE/Ground

AC Load (L1A) (Switch Leg)

Red

Power Supply Wire

Color

North America

100–120 V System Black White Green or Bare Copper Black

North America

208–240 V System Black, Red, or Blue Red, Blue, or Black Green or Bare Copper Black

Australia*

240 V System Brown or Red Black or Light Blue Green with Yellow Tracer Brown

*Special Note: If installing the fan in Australia, a licensed electrician must perform the electrical installation.

100–240VAC

1 Φ, 50/60Hz

PE / Ground

L2 / AC Neutral

L1 / AC Line

PE / Ground

L2 / AC Neutral

L1 / AC Line

L1A / AC Load (Switch Leg) (Capped)

PE / Ground

L2 / AC Neutral

L1 / AC Line

100–240VAC

1 Φ, 50/60Hz

Can be dierent

AC circuits

100–240VAC

1 Φ, 50/60Hz

PE / Ground

L2 / AC Neutral

L1 / AC Line

PE / Ground

L2 / AC Neutral

L1A / AC Load (Switch Leg)

L1A / AC Load (Switch Leg) (Optional)

PE / Ground

L2 / AC Neutral

L1 / AC Line

100–240VAC

1 Φ, 50/60Hz

PE / Ground

L2 / AC Neutral

L1 / AC Line

PE / Ground

L2 / AC Neutral

L1 / AC Line

L1A / AC Load (Switch Leg) (Capped)

PE / Ground

L2 / AC Neutral

L1 / AC Line

100–240VAC

1 Φ, 50/60Hz

Can be dierent

AC circuits

100–240VAC

1 Φ, 50/60Hz

PE / Ground

L2 / AC Neutral

L1 / AC Line

PE / Ground

L2 / AC Neutral

L1A / AC Load (Switch Leg)

L1A / AC Load (Switch Leg) (Optional)

PE / Ground

L2 / AC Neutral

L1 / AC Line

HAIKU®by BIG ASS FANS

HAIKU WALL CONTROL (CONT.)

Step 8. Test the fan(s)

Reapply AC power, and then turn on the fan(s) using the wall control to test the DIP switch address. If the wall

control does not operate the fan(s) due to interference with other radio frequency devices, turn o power to

the fan(s) and wall control, select a dierent address on the wall control, and then set the matching address

on the RF board(s). Reapply power and retest. Repeat until an appropriate address is determined.

Power to the fan(s) and wall control must be turned o during address changes. If power is on during

an address change, the change may not be accepted.

Wall Control

Junction Box

(in wall)

Wall Plate

#6-32

Screw

Step 7. Install the wall control

Install the wall control with the provided #6-32 x 7/8” screws in a location within 20 ft (6 m) of the fan. Do not

overtighten the screws. Install the wall plate using the screws provided with the wall plate. Note: If your wall

control kit does not include a wall plate, Big Ass Fans recommends using a Decora® wall plate. Other brands

may not be compatible.

Step 9. Install lower cover or (optional) LED light kit

If you purchased the Haiku LED light kit, proceed to the instructions included with the kit. If you did not

purchase the LED light kit, proceed to the step for installing the lower cover in the complete Haiku Installation

Guide.

HAIKU®by BIG ASS FANS

WALL CONTROL OPERATION

The fan is controlled independently from the light. Both the wall

control and the IR remote can be used to control the fan and the light.

Operating the fan

Ensure the Power Cuto Tab is ﬂush with the wall control face. If not,

use a pen or similar object to push it into position.

Powering the fan

To turn the fan on or o, press the On/O button on the right side of

the wall control. This button can also be used to reset the fan’s speed.

CAUTION: The fan will automatically restart at the last opera-

ting speed when power is restored!

Changing fan speed

Fan speed is increased or decreased by pressing the Up or Down

Speed button on the wall control. Several fan speeds are available to

accommodate your comfort level.

To change the fan speed, press a Speed button. The Up Speed button increases fan speed; the Down Speed

button decreases fan speed. The fan mode indicators will illuminate and a short beep will be heard until the

highest speed or 0 (o) is reached.

Timer mode

In Timer mode, the fan runs at a set speed until the programmed time period ends. Note: Timer mode is

disabled if the fan speed is 0 (o) or if the fan is not running.

To set Timer mode, press the Timer button 1–7 times (once for each hour) to program the end time. During

adjustment, the fan mode indicators will ﬂash, and then the Timer setting is displayed on the speed indicator

bar. To exit Timer mode, press the Clear button.

Sleep mode

Sleep mode reduces the fan speed by one increment every hour until the lowest speed is reached. When the

programmed time period ends, the fan automatically turns o. Sleep mode is only active when Timer mode

is used.

To activate Sleep mode, set the fan speed and Timer mode, and then press the Sleep button. The Sleep

indicator will illuminate. To exit Sleep mode, press the Sleep, Clear, or On/O button.

Whoosh mode

Whoosh mode simulates natural, relaxing breezes by automatically varying the fan speed.

To activate Whoosh mode, set the desired maximum fan speed, and then press the Whoosh button. The top

Speed indicator will ﬂash to indicate that Whoosh mode is active. To exit Whoosh mode, press the Whoosh,

Speed, or On/O button once.

HAIKU WALL CONTROL (CONT.)

4.18” (106 mm)

1.65” (42 mm)

Power

Cuto Tab

HAIKU®by BIG ASS FANS

HAIKU WALL CONTROL (CONT.)

OPERATING THE LIGHT

The Haiku LED light kit operates independently from the fan, providing a variable level of illumination that is

increased or decreased by pressing the Up or Down Light button on the wall control.

CAUTION: Do not stare directly into the light!

Powering the light

To turn the light on or o, press the Light On/O button on the left side of the wall control. The light will turn

on to the last setting when power is restored.

Changing the brightness

To increase brightness, press the Up Light button on the wall control. To decrease brightness, press the

Down Light button. To quickly increase or decrease the brightness, press and hold the Up or Down Light

button until the desired level of illumination is reached.

MAINTENANCE

Push the Power Cuto Tab at the lower end of the control face and disconnect power before performing any

maintenance. Refer to the complete Haiku Installation Guide for detailed troubleshooting and fan mainte-

nance instructions.

WARNING: Ensure AC power is disconnected at the fuse/breaker distribution panel and the Power

Cuto Tab is protruding outward (O position) before performing any maintenance on the fan or

wall control.

CAUTION: The fan will automatically restart at the last operating speed when power is restored!

Power Cuto Tab

(O position)

*003927*

003927

REV. I

Inhaltsverzeichnis

Andere Bigassfans Controller Handbücher

Bigassfans

Bigassfans SmartSense Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung