Billion BiGuard 30 Bedienungsanleitung

BiGuard 30

iBusiness Security Gateway SMB

User’s Manual

Version Release 5.00 (FW:1.03)

BiGuard 30 User’s Manual

(Updated December 1, 2005)

The contents of this publication may not be reproduced in whole or in part,

transcribed, stored, translated, or transmitted in any form or any means, without

the prior written consent of Billion Electric Corporation.

Disclaimer

Billion does not assume any liability arising out of the application of use of any

products or software described herein. Neither does it convey any license under its

patent rights nor the patent rights of others. Billion reserves the right to make

changes in any products described herein without notice. This publication is subject

to change without notice.

Trademarks

Mac OS is a registered trademark of Apple Computer, Inc.

Windows 98, Windows NT, Windows 2000, Windows Me and Windows XP are

registered trademarks of Microsoft Corporation.

Safety Warnings

Your BiGuard 30 is built for reliability and long service life. For your safety,

be sure to read and follow the following safety warnings.

•Read this installation guide thoroughly before attempting to set up your BiGuard

30.

•Your BiGuard 30 is a complex electronic device. DO NOT open or attempt to

repair it yourself. Opening or removing the covers can expose you to high

voltage and other risks. In the case of malfunction, turn off the power

immediately and have it repaired at a qualified service center. Contact your

vendor for details.

•Connect the power cord to the correct supply voltage.

•Carefully place connecting cables to avoid people from stepping or tripping on

them. DO NOT allow anything to rest on the power cord and DO NOT place the

power cord in an area where it can be stepped on.

•DO NOT use BiGuard 30 in environments with high humidity or high

temperatures.

•DO NOT use the same power source for BiGuard 30 as other equipment.

•DO NOT use your BiGuard 30 and any accessories outdoors.

•If you wall mount your BiGuard 30, make sure that no electrical, water or gas

pipes will be damaged during installation.

•DO NOT install or use your BiGuard 30 during a thunderstorm.

•DO NOT expose your BiGuard 30 to dampness, dust, or corrosive liquids.

•DO NOT use your BiGuard 30 near water.

•Be sure to connect the cables to the correct ports.

•DO NOT obstruct the ventilation slots on your BiGuard 30 or expose it to direct

sunlight or other heat sources. Excessive temperatures may damage your

device.

•DO NOT store anything on top of your BiGuard 30.

•Only connect suitable accessories to your BiGuard 30.

•Keep packaging out of the reach of children.

•If disposing of the device, please follow your local regulations for the safe

disposal of electronic products to protect the environment.

Table of Contents

Chapter 1: Introduction

1.1 Overview

1.2 Product Highlights

1.2.1 Increased Bandwidth, Scalability and Resilience

1.2.2 Virtual Private Network Support

1.2.3 Advanced Firewall Security

1.2.4 Intelligent Bandwidth Management

1.3 Package Contents

1.3.1 Front Panel

1.3.2 Rear Panel

1.3.3 Rack Mounting

1.3.4 Cabling

Chapter 2: Router Applications

2.1 Overview

2.2 Bandwidth Management with QoS

2.2.1 QoS Technology

2.2.2 QoS Policies for Different Applications

2.2.3 Guaranteed / Maximum Bandwidth

2.2.4 Policy Based Traffic Shaping

2.2.5 Priority Bandwidth Utilization

2.2.6 Management by IP or MAC address

2.2.7 DiffServ (DSCP Marking)

2.3 Outbound Traffic

2.3.1 Outbound Fail Over

2.3.2 Outbound Load Balancing

2.4 Inbound Traffic

2.4.1 Inbound Fail Over

2.4.2 Inbound Load Balancing

2.5 DNS Inbound

2.5.1 DNS Inbound Fail Over

2.5.2 DNS Inbound Load Balancing

2.6 Virtual Private Networking

2.6.1 General VPN Setup

2.6.2 VPN Planning - Fail Over

2.6.3 Concentrator

Chapter 3: Getting Started

3.1 Overview

3.2 Before You Begin

3.3 Connecting Your Router

3.4 Configuring PCs for TCP/IP Networking

3.4.1 Overview

3.4.2 Windows XP

3.4.2.1 Configuring

3.4.2.2 Verifying Settings

3.4.3 Windows 2000

3.4.3.1 Configuring

3.4.3.2 Verifying Settings

3.4.4 Windows 98 / ME

3.4.4.1 Installing Components

3.4.4.2 Configuring

3.4.4.3 Verifying Settings

3.5 Factory Default Settings

3.5.1 Username and Password

3.5.2 LAN and WAN Port Addresses

3.6 Information From Your ISP

3.6.1 Protocols

3.6.2 Configuration Information

3.6.2.1 Windows

3.7 Web Configuration Interface

Chapter 4: Router Configuration

4.1 Overview

4.2 Status

4.2.1 ARP Table

4.2.2 Routing Table

4.2.3 Session Table

4.2.4 DHCP Table

4.2.5 IPSec Status

4.2.6 PPTP Status

4.2.7 Traffic Statistics

4.2.8 System Log

4.2.9 IPSec Log

4.3 Quick Start

4.3.1 DHCP

4.3.2 Static IP

4.3.3 PPPoE

4.3.4 PPTP

4.3.5 Big Pond

4.4 Configuration

4.4.1 LAN

4.4.1.1 Ethernet

4.4.1.2 DHCP Server

4.4.2 WAN

4.4.2.1 ISP Settings

4.4.2.1.1 DHCP

4.4.2.1.2 Static IP

4.4.2.1.3 PPPoE

4.4.2.1.4 PPTP

4.4.2.1.5 Big Pond

4.4.2.2 Bandwidth Settings

4.4.3 Dual WAN

4.4.3.1 General Settings

4.4.3.2 Outbound Load Balance

4.4.3.3 Inbound Load Balance

4.4.3.4 Protocol Binding

4.4.4 System

4.4.4.1 Time Zone

4.4.4.2 Remote Access

4.4.4.3 Firmware Upgrade

4.4.4.4 Backup / Restore

4.4.4.5 Restart

4.4.4.6 Password

4.4.4.7 System Log Server

4.4.4.8 Email Alert

4.4.5 Firewall

4.4.5.1 Packet Filter

4.4.5.2 URL Filter

4.4.5.3 LAN MAC Filter

4.4.5.4 Block WAN Request

4.4.5.5 Intrusion Detection

4.4.6 VPN

4.4.6.1 IPSec

4.4.6.1.1 IPSec Wizard

4.4.6.1.2 IPSec Policy

4.4.6.2 PPTP

4.4.7 QoS

4.4.8 Virtual Server

4.4.8.1 DMZ

4.4.8.2 Port Forwarding Table

4.4.9 Advanced

4.4.9.1 Static Route

4.4.9.2 Dynamic DNS

4.4.9.3 Device Management

4.5 Save Configuration To Flash

4.6 Logout

Chapter 5: Troubleshooting

5.1 Basic Functionality

5.1.1 Router Won’t Turn On

5.1.2 LEDs Never Turn Off

5.1.3 LAN or Internet Port Not On

5.1.4 Forgot My Password

5.2 LAN Interface

5.2.1 Can’t Access Router from the LAN

5.2.2 Can’t Ping Any PC on the LAN

5.2.3 Can’t Access Web Configuration Interface

5.2.3.1 Pop-up Windows

5.2.3.2 Javascripts

5.2.3.3 Java Permissions

5.3 WAN Interface

5.3.1 Can’t Get WAN IP Address from the ISP

5.4 ISP Connection

5.5 Problems with Date and Time

5.6 Restoring Factory Defaults

Appendix A: Product Specifications

Appendix B: Customer Support

Appendix C: FCC Interference Statement

Appendix D: Network, Routing, and Firewall Basics

D.1 Network Basics

D.1.1 IP Addresses

D.1.1.1 Netmask

D.1.1.2 Subnet Addressing

D.1.1.3 Private IP Addresses

D.1.2 Network Address Translation (NAT)

D.1.3 Dynamic Host Configuration Protocol (DHCP)

D.2 Router Basics

D.2.1 Why use a Router?

D.2.2 What is a Router?

D.2.3 Routing Information Protocol (RIP)

D.3 Firewall Basics

D.3.1 What is a Firewall?

D.3.2.1 Stateful Packet Inspection

D.3.2.2 Denial of Service (DoS) Attack

D.3.2 Why Use a Firewall?

Appendix E: Virtual Private Networking

E.1 What is a VPN?

E.1.1 VPN Applications

E.2 What is IPSec?

E.2.1 IPSec Security Components

E.2.1.1 Authentication Header (AH)

E.2.1.2 Encapsulating Security Payload (ESP)

E.2.1.3 Security Associations (SA)

E.2.2 IPSec Modes

E.2.3 Tunnel Mode AH

E.2.4 Tunnel Mode ESP

E.2.5 Internet Key Exchange (IKE)

Appendix F: IPSec Logs and Events

F.1 IPSec Log Event Categories

F.2 IPSec Log Event Table

Appendix G: Bandwidth Management with QoS

G.1 Overview

G.2 What is Quality of Service?

G.3 How Does QoS Work?

G.4 Who Needs QoS?

G.4.1 Home Users

G.4.2 Office Users

Appendix H: Router Setup Examples

H.1 Outbound Fail Over

H.2 Outbound Load Balancing

H.3 Inbound Fail Over

H.4 DNS Inbound Fail Over

H.5 DNS Inbound Load Balancing

H.6 Dynamic DNS Inbound Load Balancing

H.7 VPN Configuration

H.7.1 LAN to LAN

H.7.2 Host to LAN

H.8 IPSec Fail Over (Gateway to Gateway)

H.9 VPN Concentrator

H.10 Protocol Binding

H.11 Intrusion Detection

H.12 PPTP Remote Access by Windows XP

H.13 PPTP Remote Access by BiGuard

Chapter 1: Introduction

1.1 Overview

Congratulations on purchasing BiGuard 30 Router from Billion. Combining a router

with an Ethernet network switch, BiGuard 30 is a state-of-the-art device that

provides everything you need to get your network connected to the Internet over

your Cable or DSL connection quickly and easily. The Quick Start Wizard and DHCP

Server will get first-time users up and running with minimal fuss and configuration,

while sophisticated Quality of Service (QoS) and Load Balancing features grant

advanced users total control over their network and Internet connection.

This manual illustrates the many features and functions of BiGuard 30, and even

takes you through the various ways you can apply this versatile device to your home

or office. Take the time now to familiarize yourself with BiGuard 30.

1.2 Product Highlights

1.2.1 Increased Bandwidth, Scalability and Resilience

With integrated Dual WAN ports, BiGuard 30 combines two broadband lines such as

DSL or Cable into one Internet connection, providing optimal bandwidth sharing for

multiple PCs on your network, or allowing maximum reliability with network

redundancy. Load Balancing enables BiGuard 30 to efficiently balance network

traffic across two connections, ideal for small-to-medium businesses that require

increased bandwidth, network scalability, and resilience for mission-critical network

and Internet applications. Auto failover can also be configured to ensure smooth,

continuous service should one connection fail, providing maximum business uptime

and productivity, plus uninterrupted service for you and your customers.

1.2.2 Virtual Private Network Support

BiGuard 30 supports comprehensive IPSec & PPTP VPN protocols for businesses to

establish private encrypted tunnels over the Internet to ensure data transmission

security among multiple sites, such as a branch office or dial-up connection. IPSec

VPN is up to 30 simultaneous IPSec VPN connections are possible on BiGuard 30,

with performance of up to 30Mbps. PPTP VPN is up to 4 simultaneous PPTP VPN

Andere Handbücher für BiGuard 30

Inhaltsverzeichnis

Andere Billion Tor Handbücher

Billion

Billion Bipac 9800 VNX Bedienungsanleitung

Billion

Billion BiGuard 10 Bedienungsanleitung

Billion

Billion SG6200NXL Bedienungsanleitung

Billion

Billion BiGuard 2 Bedienungsanleitung

Billion

Billion BiGuard S10 Bedienungsanleitung

Billion

Billion BiGuard 50G Bedienungsanleitung

Billion

Billion BiGuard 30 Bedienungsanleitung

Billion

Billion BiGuard 50G Installations- und Betriebshandbuch

Billion

Billion BiGuard 50G Bedienungsanleitung

Billion

Billion BiGuard S10 Bedienungsanleitung

Billion

Billion BiGuard S3000 Bedienungsanleitung

Billion

Billion BiGuard S100N Bedienungsanleitung

Billion

Billion BiGuard 50G Bedienungsanleitung

Billion

Billion BiGuard 2 Bedienungsanleitung

Billion

Billion BiGuard 10 Bedienungsanleitung

Billion

Billion SG6300NZL Bedienungsanleitung

Billion

Billion BiGuard 30 Bedienungsanleitung

Billion

Billion BiGuard 2 Bedienungsanleitung

Billion

Billion BiGuard 10 Bedienungsanleitung

Billion

Billion BiGuard 50G Bedienungsanleitung

Billion

Billion BiGuard S10 Bedienungsanleitung

Billion

Billion BiGuard 30 Bedienungsanleitung

Billion

Billion BiGuard S10 Bedienungsanleitung

Billion

Billion BiGuard S5 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung