Billy Goat Z FORCE FZ1300H Bedienungsanleitung

Part No 442503 Form No F081512A

Z FORCE BLOWER Owner’s Manual

Patents Pending

FZ1300H

BILLY GOAT Z FORCE BLOWER

Owner's Manual

*JRCO Universal Mount Not Included*

Contact your Billy Goat Dealer or visit http://jrcoinc.com/ for a list of

JRCO Products

Part No 442503 Form No F081512A

Z FORCE BLOWER Owner’s Manual

CONTENTS

SPECIFICATIONS _______________________ 3

SAFETY INSTRUCTIONS AND WARNINGS_________________________________4-5

INSTRUCTION LABELS 6

PACKING CHECKLIST 7

ASSEMBLY 8

OPERATION __ 9

MAINTENANCE AND WARRANTY INFO ____ 10

TROUBLESHOOTING AND WIRING DIAGRAM ______________________________11

ILLUSTRATED PARTS LIST 12

PARTS LIST 13

MAINTENANCE RECORD________________________________________________14

Part No 442503 Form No F081512A

Z FORCE BLOWER Owner’s Manual

Specifications FZ1300H

Engine: HP

13.0 HP (9.6kW)

Engine: Model

GX390K1QAA2

Engine: Type

HONDA OHV

Engine: Fuel Capacity

6.5 qt. (6.1L)

Engine: Oil Capacity

1.16 qt. (1.1L)

Total Unit Weight:

192 # (87Kg)

Overall Length:

42"(1.1m)

Overall Width

35.5” (0.90m)

Max operating slope

20 deg.

SOUND

SOUND LEVEL 87 Db(a) at Operators Position (seated on Zero Turn Mower)

Sound tests were conducted in accordance with 2000/14/EC, as well as ISO 11094, and were performed on 6-30-

2011 under the conditions listed below.

Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on

the unit for the sound power level for your model.

General Conditions: Sunny

Temperature: 86oF (30oC)

Wind Speed: 13 mph (20.1 kph)

Wind Direction: South

Humidity: 62%

Barometric Pressure: 29.94 Hg (101.4 kpa)

107 dB

Part No 442503 Form No F081512A

Z FORCE BLOWER Owner’s Manual

GENERAL SAFETY INSTRUCTIONS and SYMBOLS

The safety symbols shown below are used throughout this manual. You should become familiar with them before

assembling, operating, or servicing this equipment.

This symbol indicates important information that will prevent injury to yourself or others.

This symbol indicates ear protection is recommended when operating this equipment.

This symbol indicates eye protection is recommended when operating this equipment.

This symbol indicates gloves should be worn when servicing this equipment.

This symbol indicates that this manual and the engine manufacturer’s manual should be read

carefully before assembling, operation, or servicing this equipment.

This symbol indicates important information that will prevent damage to your BILLY GOAT ®

Z FORCE Blower.

This symbol indicates the engine oil level should be checked before operating this

equipment.

Read and make sure you thoroughly understand the following safety precautions before assembling, operating or

servicing this equipment:

READ this manual and the engine manufacturer’s manual carefully before assembling,

operating, or servicing this equipment.

EAR PROTECTION is recommended when operating this equipment.

EYE PROTECTION is recommended when operating this equipment.

BREATHING PROTECTION is recommended when operating this equipment.

EXHAUST from this product contains chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm.

DO NOT operate this equipment on any unimproved forested, brushy, or grass covered land

unless a spark arrester is installed on the muffler as required by Section 4442 of the

California Public Resources Code. The arrester must be maintained in good working order.

Other states may have similar laws. Federal laws apply on federal lands.

DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an

odorless and possibly fatal poison.

Part No 442503 Form No F081512A

Z FORCE BLOWER Owner’s Manual

DO NOT run this equipment indoors or in any poorly ventilated area. Refueling outdoors is

recommended.

DO NOT refuel this equipment while the engine is running. Allow engine to cool for at least two minutes

before refueling.

DO NOT store gasoline near an open flame.

DO NOT remove gas cap while engine is running.

DO NOT start or operate engine if strong odor of gasoline is present.

DO NOT start or operate engine if gasoline is spilled. Move equipment away from spill until gasoline has

completely evaporated.

DO NOT smoke while filling the fuel tank.

DO NOT check for spark with spark plug or spark plug wire removed. Use an approved spark tester.

DO NOT operate engine without a muffler. Inspect muffler periodically and replace if necessary. If

equipped with muffler deflector, inspect deflector periodically and replace if necessary.

DO NOT operate engine with grass, leaves or other combustible material near the muffler.

DO NOT touch muffler, cylinder, or cooling fins when hot. Contact with hot surfaces may cause severe

burns.

DO NOT leave equipment unattended while in operation.

DO NOT park equipment on a steep grade or slope.

DO NOT operate equipment with bystanders in or near the work area.

DO NOT allow children to operate this equipment.

DO NOT operate equipment with guards removed.

DO NOT operate equipment near hot or burning debris or any toxic or explosive materials.

DO NOT operate equipment on slopes greater than specified in Specifications section of this manual.

DO NOT operate near steep embankments or drop offs.

DO NOT transport this unit attached at excessive speeds, doing so may result in serious injury or death.

ALWAYS make sure the machine is attached to the mower securely.

ALWAYS remove spark plug wire when servicing equipment to prevent accidental starting.

ALWAYS wear your seatbelt when using this machine.

ALWAYS check fuel lines and fittings frequently for cracks or leaks. Replace if necessary.

ALWAYS keep hands and feet away from moving or rotating parts.

ALWAYS store fuel in approved safety containers.

ALWAYS shut of gas flow valve when transporting machine.

WARNING: Important

Do not run this machine without exhaust elbow attached.

DO NOT run this machine with a cracked or damaged impeller under any circumstances.

Part No 442503 Form No F081512A

Z FORCE BLOWER Owner’s Manual

INSTRUCTION LABELS

The labels shown below were installed on your BILLY GOAT ®Z FORCE Blower. If any labels are damaged or

missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part

numbers are provided for convenience in ordering replacement labels. The correct position for each label may be

determined by referring to the Figure and Item numbers shown.

DANGER FLYING DEBRIS LABEL THROTTLE CONTROL

ITEM # 18 P/N 810736 ITEM # 72 P/N 810656

LABEL WARNING FZ

ITEM #2 P/N 442500

ENGINE LABELS

HONDA

LABEL SPARK ARRESTOR

P/N 100252

Part No 442503 Form No F081512A

Z FORCE BLOWER Owner’s Manual

PACKING CHECKLIST

These items should be included in your carton. If any of these parts are missing, contact your dealer.

Your BILLY GOAT ®Z FORCE Blower was shipped in one carton, completely assembled. Mounting hardware can

be found on the attachment points on the frame.

READ all safety instructions before attaching unit.

TAKE CAUTION when removing the unit from the box the switch pedal assembly is attached

by cables.

PUT OIL IN ENGINE BEFORE STARTING

Boxing Parts Checklist

Switch pedal Assy

Parts Bag & Literature Assy

P/N-442006

Honda 13 HP engine manual

JRCO Bracket Adapter P/N-

442203

PARTS BAG &

LITERATURE ASSY

Warranty card P/N- 400972, Owner’s Manual P/N-442503

Part No 442503 Form No F081512A

Z FORCE BLOWER Owner’s Manual

ASSEMBLY

Figure A Figure B

Proper mounting Improper mounting

Wires tied down Wires not tied down

1.Follow the steps in figures A and B, then securely tighten all hardware shown.

2.Connect spark plug wire on the blower.

Make sure your JRCO bar is attached to your mower.

Then replace the mounting bracket with the bracket

provided (item 4). Attach the Blower to brackets and

install the pins making sure they are completely pushed

in. NOTE some JRCO bars will require mounting to the

outside ears of the blower bracket (15” Center).

Ensure the unit is mounted level, failure to do so may

result in poor handling and will put stress on the blower

frame. Level the unit by adjusting the mounting brackets

(item 4) up or down depending on your mower.

Connect the rear portion of the wiring harness to the

mower battery by attaching the red wire to the positive

terminal and the black wire to the negative terminal.

Route the harness so that the connector is located at the

foot rest portion of the mower. Note make sure the

position of the switch box will not interfere with mower

operation controls. Secure any excess length of wire to

the frame of the mower using ty wraps. FAILURE TO

CONTAIN EXCESS WIRE WILL RESULT IN WIRE

COMING INTO CONTACT WITH MOVING PARTS ON

MOWER (belts, blades, brake pedals, etc.) FAILURE TO

PROPERLY SECURE WIRING HARNESS WILL

RESULT IN FAILURE AND IS NOT COVERED UNDER

WARRANTY!

Part No 442503 Form No F081512A

Z FORCE BLOWER Owner’s Manual

BLOWING OPERATION

Your Billy Goat Z Force blower is equipped with a motorized air director nozzle to allow the operator to direct the air

stream by rotating left or right as required to assist in moving debris. This feature is extremely useful when having to

move debris in various directions.

ADJUSTING AIR DIRECTOR

To change the air direction use the foot pedal switch to rotate the nozzle clockwise (CW) or counter-clockwise (CCW).

Use the red indicator as a visual guide to show which way the nozzle is pointing when out of view. Note: Switch must be

hooked up to battery in order to function.

DO NOT position exhaust nozzle to where it will blow debris towards people, vehicles or other objects in vicinity. Flying

debris may damage, harm, or cause injury to people or objects in air flow range.

Always make sure the kickstand is up before unit is put in motion to raise the kickstand pull out the pin and rotate the

kickstand up towards the blower. Locate the hole that holds it in the upwards position and re-insert the pin. Likewise,

before detaching the unit from the mower make sure the kickstand is down and locked in position.

Part No 442503 Form No F081512A

Z FORCE BLOWER Owner’s Manual

MAINTENANCE

PERIODIC MAINTENANCE

Periodic maintenance should be performed at the following intervals:

Maintenance Operation

Every

Use

Daily or Every

5 Hours

Every 25

Hours

Every 50

Hours

Every

100-150

Hours

Inspect for worn or damaged parts.



Check for excessive vibration



Grease Casters and Exhaust elbow



Inspect Impeller for cracks or damage



Inspect for loose parts.



IMPELLER REMOVAL

1. Wait for engine to cool and disconnect spark plug.

2. Remove housing front cover, by removing (11) nuts, items #49, around outside of front cover.

3. Remove impeller bolt (item #12), lock washer (item #8) and washer (item #38).

4. DO NOT pry on impeller. Pull on center hub area only of impeller. Using a penetrating oil can help loosen a stuck

impeller.

5. Reinstall new impeller in reverse order of removal using new hardware including the key.

6. Tighten impeller bolt. Torque impeller bolt (see parts list on page 13 for proper impeller bolt torque specifications).

When servicing engine refer to specific manufacturer’s engine owner's manual. Engine warranty is covered by the specific

engine manufacturer. If your engine requires warranty or other repair work, contact your local servicing engine dealer. When

contacting a dealer for service it is a good idea to have your engine model number available for reference (See table page 3). If

you cannot locate a servicing dealer in your area you can contact the manufacturer’s national service organization.

To reach:

American Honda: 800-426-7701

WARRANTY CLAIM PROCEDURE

Should a BILLY GOAT ®machine fail due to a defect in material and/or workmanship, the owner should make a warranty claim

as follows:

The machine must be taken to the dealer from whom it was purchased or to an authorized Servicing BILLY GOAT

Dealer.

The owner must present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or

receipt.

The Warranty Claim will be completed by the authorized BILLY GOAT Dealer and submitted to their respective BILLY

GOAT Distributor for their territory Attention: Service Manager. Any parts replaced under warranty must be tagged and

retained for 90 days. The model number and serial number of the unit must be stated in the Warranty Claim.

The distributor service manager will sign off on the claim and submit it to BILLY GOAT for consideration.

The Technical Service Department at BILLY GOAT will study the claim and may request parts to be returned for

examination. BILLY GOAT will notify their conclusions to the distributor service manager from whom the claim was

received.

The decision by the Technical Service Department at BILLY GOAT to approve or reject a Warranty Claim is final and

binding.

For online product registration go to www.billygoat.com

Inhaltsverzeichnis

Andere Billy Goat Gebläse Handbücher

Billy Goat

Billy Goat F091907A Bedienungsanleitung

Billy Goat

Billy Goat FORCE 601V Bedienungsanleitung

Billy Goat

Billy Goat QUIET BLOW QB1100HPN Bedienungsanleitung

Billy Goat

Billy Goat HURRICANE X3000 Bedienungsanleitung

Billy Goat

Billy Goat QUIET BLOW QB553 Montageanleitung

Billy Goat

Billy Goat KV600SP Bedienungsanleitung

Billy Goat

Billy Goat QUIET BLOW QB1601 Montageanleitung

Billy Goat

Billy Goat F902SPS Bedienungsanleitung

Billy Goat

Billy Goat QUIET BLOW QB553HC Montageanleitung

Billy Goat

Billy Goat F1002V Bedienungsanleitung

Billy Goat

Billy Goat F1002SPV Bedienungsanleitung

Billy Goat

Billy Goat MV VACUUM PUSH EU MV601EU Bedienungsanleitung

Billy Goat

Billy Goat Force Blower Bedienungsanleitung

Billy Goat

Billy Goat QUIET BLOW QB501CE Montageanleitung

Billy Goat

Billy Goat F902S Bedienungsanleitung

Billy Goat

Billy Goat QUIET BLOW QB1004 Montageanleitung

Billy Goat

Billy Goat DL1302H Bedienungsanleitung

Billy Goat

Billy Goat F902S Bedienungsanleitung

Billy Goat

Billy Goat QUIET BLOW QB554HC Bedienungsanleitung

Billy Goat

Billy Goat F1801V Bedienungsanleitung

Billy Goat

Billy Goat BLOWER QB882 Montageanleitung

Billy Goat

Billy Goat FORCE F601V Bedienungsanleitung

Billy Goat

Billy Goat MV650H PUSH Bedienungsanleitung

Billy Goat

Billy Goat 440021 Bedienungsanleitung

Beliebte Gebläse Handbücher anderer Marken

Weed Eater

Weed Eater VS2000BV Bedienungsanleitung

KRAUSMANN

KRAUSMANN U37020-00 Bedienungsanleitung

Cub Cadet

Cub Cadet HB425 Bedienungsanleitung

GreenWorks Pro

GreenWorks Pro BLB482 Bedienungsanleitung

ARIETE

ARIETE 2768 Bedienungsanleitung

NuTone

NuTone 331H Bedienungsanleitung

GÜDE

GÜDE GLB 200 18 Li-Ion Bedienungsanleitung

I.VA.CO.

I.VA.CO. SC Series Betriebsanleitung

DeWalt

DeWalt DCE100 Bedienungsanleitung

Becker

Becker SV 7.330 Bedienungsanleitung

Metabo

Metabo AG 18 Pro Bedienungsanleitung

Desa

Desa GA3650TB Bedienungsanleitung

Echo

Echo Power Blower PB-230LN Bedienungsanleitung

Echo

Echo PB-413H Bedienungsanleitung

Black & Decker

Black & Decker BV3100 Bedienungsanleitung

Ryobi

Ryobi RY08570 Bedienungsanleitung

Haaga

Haaga 355 Bedienungsanleitung

Stiga

Stiga SBL 327 V Bedienungsanleitung