Binary B-900-MOIP Series Bedienungsanleitung
Source | Mute | 2ch
(HDMI Out Audio)
INSTALLATION & SETUP GUIDE
MEDIA OVER IP SYSTEM
All B-900-MOIP Units
2
3
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of re or electric shock, read and follow all instructions and warnings in this
manual. Keep this manual for future reference.
1. Do not expose to water.
2. Do not remove cover. No user serviceable parts inside.
3. Clean only with a dry cloth.
4. Leave sufcient space between devices and do not block ventilation holes for proper
cooling.
5. Do not stack transmitter or receivers on top of each other.
6. Do not install near any device or source that generates heat.
7. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including ampliers) that produce heat.
8. Do not override the safety purpose of the polarized or grounding plug. A polarized plug has
two blades, one of which is wider than the other. A grounding plug has two matching blades
and a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not t into your outlet, consult an electrician for replacement of the
obsolete outlet.
9. Protect the power cord from being walked on or pinched, particularly at the plug end and
where the power cord is attached to the apparatus.
10. Only use manufacturer’s recommended power supply if the use of an external power supply
for the transmitter and receiver is necessary.
11. Only use attachments and accessories specied by the manufacturer.
12. Refer all servicing to qualied service personnel. Servicing is required when the apparatus
has been damaged in any way, such as when the power supply cord or plug is damaged,
liquid has been spilled on or objects have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, the apparatus does not operate normally, or it has been
dropped.
13. Disconnect the power supply cord from the power outlet, or disconnect the transmitter
and receivers from the network PoE connections or remove the network switch power cord
from the outlet, to completely disconnect the controller from power.
LEGAL NOTICE
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D
symbol are trademarks of Dolby Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. DTS,
the Symbol, DTS and the Symbol together, Digital Surround, and the DTS 2.0+Digital Out
logo, are registered trademarks or trademarks of DTS, Inc. in the United States and/or other
countries. © DTS, Inc. All Rights Reserved.
4
GETTING STARTED
To get started, you need:
• 1× per source: MoIP Transmitter
• 1× per display: MoIP Receiver
• 1× MoIP Controller B-900-MOIP-4K-CTRL
• 1× Layer 2 Managed switch
• Sources, Displays, HDMI cables and category cabling
MoIP Controller B-900-MOIP-4K-CTRL
B-900-MOIP-4K-CTRL
CONTROLLER
Reboot Factory Default
Network
+5VDC
A. Status LED
Solid during system boot | Blinks during normal operation.
B. Reboot Button
Use a pin to press the recessed button to restart the controller.
C. USB Ports
For use with a USB-to-Ethernet adapter. See the Network Troubleshooting section for
more information.
D. Network/LAN Port
Connect to MoIP switch to provide access to MoIP transmitters and receivers.
E. HDMI Port
Not used for the MoIP system.
F. 12 VDC Power Connection
Connect the provided power supply.
G. Factory Default button
Use a pin to press the recessed button 3 times within 10 seconds to restore factory
settings.
A
B G
CD E F
5
MoIP Transmitter B-900-MOIP-4K-TX
A. Power Indicator
On: Power on | Blinking: Booting | Off: Power off
B. System Status Light
On: Connected to network with source present | Off: Not connected to network |
Blinking: Connected to network and no source present.
C. Network Port
Provides access to network and power via Power-over-Ethernet (POE).
D. DIP Switches
Switch 1: IR receiver on/Off | Switch 2: DTE/DCE .
E. 3.5 mm Input
Analog audio embedding to replace HDMI audio.
F. L/R Audio Out
RCA analog audio de-embedding of 2-channel PCM audio.
G. RS-232
RJ45, RS-232, (TX, RX, Ground), EIA-561 pin out.
H. HDMI IN/OUT
HDMI source input and HDMI loop output for local display.
I. IR Receiver
3.5 mm mini Mono/Stereo for external receivers.
J. IR Flasher
3.5 mm mini Mono output to IR emitter.
K. Factory Reset
Press and hold for 10 seconds to restore to factory settings.
L. 12 V 2A Power Connection
12VDC 2A locking connection for external power supply (not included).
C E G I LJD F H K
A B
6
MoIP Transmitter B-900-MOIP-4K-TX-2AC
A. Power Indicator
On: Power on | Blinking: Booting | Off: Power off
B. System Status Light
On: Connected to network with source present | Off: Not connected to network |
Blinking: Connected to network and no source present.
C. DTS LED
Blue = DTS Surround; Red = DTS HD; Purple =DTS HD Master Audio.
D. Dolby LED
Blue = Dolby Digital; Red = Dolby Digital Plus; Purple = Dolby True HD.
E. Network Port
Provides access to network and power via Power-over-Ethernet (POE).
F. SPDIF Out
For future use only.
G. L/R Audio Out
RCA analog audio de-embedding of 2-channel PCM audio.
H. Audio In
3.5 mm input for embedding audio to replace HDMI audio.
I. RS-232
RJ45, RS-232, (TX, RX, Ground), EIA-561 pin out.
J. HDMI IN/OUT
HDMI source input and HDMI loop output for local display.
K. IR Receiver
3.5 mm mini Mono/Stereo for external receivers.
L. IR Flasher
3.5 mm mini Mono output to IR emitter.
M. Factory Reset
Press and hold for 10 seconds to restore to factory settings.
N. 12 V 2A Power Connection
12VDC 2A locking connection for external power supply (not included).
E I K NLF H J M
A B C D
G
7
MoIP Audio Transmitter B-900-MOIP-AUDIO-TX
A. Power Indicator
On: Power On | Blinking: Booting | Off: Power off
B. System Status Light
On: Connected to network with source present | Off: Not connected to network |
Blinking: Connected to network and no source present.
C. Network Port
Provides access to network and power via Power-over-Ethernet (POE).
D. L/R Audio In
RCA analog audio input.
E. Ground Screw (optional)
In certain installations, ground related audio noise issues may occur. This noise can be
suppressed by connecting this ground screw terminal to a local AC ground.
F. Factory Reset
Press and hold for 10 seconds to restore to factory settings.
G. 12 V 2A Power Connection
12VDC 2A locking connection for external power supply (not included).
E GF
A B
C D
8
MoIP Receiver B-900-MOIP-4K-RX
A. Power Indicator
On: Power on | Blinking: Booting | Off: Power off
B. System Status Light
On: Connected to network and not subscribed to transmitter stream | Off: Not
connected to network | Blinking: Connected to network and subscribed to transmitter
stream.
C. Network Port
Provides access to network and power via Power-over-Ethernet (POE).
D. DIP Switches
Switch 1: IR receiver On/Off | Switch 2: DTE/DCE.
E. L/R Audio Out
RCA analog 2-channel audio.
F. RS-232
RJ45, RS-232, (TX, RX, Ground), EIA-561 pin out.
G. HDMI OUT
HDMI output for display.
H. IR Receiver
3.5 mm mini Mono/Stereo for external receivers.
I. IR Flasher
3.5 mm mini Mono output to IR emitter/asher.
J. Factory Reset
Press and hold for 10 seconds to restore to factory settings.
K. 12 V 2A Power Connection
12VDC 2A locking connection for external power supply (not included).
C F H KID E G J
A B
9
MoIP Receiver B-900-MOIP-4K-RX-2AC
A. Power Indicator
On: Power on | Blinking: Booting | Off: Power off
B. System Status Light
On: Connected to network and not subscribed to transmitter stream | Off: Not
connected to network | Blinking: Connected to network and subscribed to transmitter
stream.
C. DTS LED
Blue = DTS Surround; Red = DTS HD; Purple =DTS HD Master Audio.
D. Dolby LED
Blue = Dolby Digital; Red = Dolby Digital Plus; Purple = Dolby True HD.
E. Network Port
Provides access to network and power via Power-over-Ethernet (POE).
F. L/R Audio Out
RCA analog 2-channel audio.
G. Audio In
3.5 mm input for embedding audio to replace HDMI audio .
H. SPDIF In
For future use only.
I. RS-232
RJ45, RS-232, (TX, RX, Ground), EIA-561 pin out.
J. HDMI OUT
HDMI output for display.
K. IR Receiver
3.5 mm mini Mono/Stereo for external receivers.
L. IR Flasher
3.5 mm mini Mono output to IR emitter/asher.
M. Factory Reset
Press and hold for 10 seconds to restore to factory settings.
N. 12 V 2A Power Connection
12VDC 2A locking connection for external power supply (not included).
A B
E H J KF G I L
C D
M N
10
MoIP Audio Receiver B-900-MOIP-AUDIO-RX
A. Power Indicator
On: Power on | Blinking: Booting | Off: Power off
B. System Status Light
On: Connected to network with source present | Off: Not connected to network |
Blinking: Connected to network and no source present.
C. Network Port
Provides access to network and power via Power-over-Ethernet (POE).
D. L/R Audio In
RCA analog audio output.
E. Ground Screw (optional)
In certain installations, ground related audio noise issues may occur. This noise can be
suppressed by connecting this ground screw terminal to a local AC ground.
F. Factory Reset
Press and hold for 10 seconds to restore to factory settings.
G. 12 V 2A Power Connection
12VDC 2A locking connection for external power supply (not included).
E GF
A B
C D
Dieses Handbuch passt für folgende Modelle
7
Inhaltsverzeichnis
Beliebte Tor Handbücher anderer Marken
LST
LST M500RFE-AS Bedienungsanleitung
Kinnex
Kinnex Media Gateway Bedienungsanleitung
2N Telekomunikace
2N Telekomunikace 2N StarGate Bedienungsanleitung
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung
Telsey
Telsey CPVA 500 - SIP Bedienungsanleitung
