BINDTEC YL-420 Bedienungsanleitung
YL-420(S)
USER MANUAL
CONTENTS
1. Safety Features Overview and Precaution
2. Product Introduction and Accessories
3. Part Names and Functions
4. Band Installation
4-1) How to feed the band for 420(30)(50)
4-2) How to feed the band for 420S
5. Operation
5-1) How to change Standby Time before Banding
5-2) Banding Regardless of Sensor Detecting an Object
6. Sheet Replacement
6-1) Life expectancy of Heater Sheet
6-2) How to check the Condition of Sheet
7. Failed Band Removal
8. Checking before Troubleshooting
9. Extra Functions
9-1) Band Removal in case of Jam
9-2) Banding Black or Transparent Objects
9-3) Banding Soft Object
10. Specifications
Product Warranty
1
Safety Features Overview and Precaution
For your safety
Please read this user manual carefully
before operating the banding machine.
Maintenance requirements
1. Make sure that the power is supplied. Voltage fluctuation must be kept at a
minimum.
2. High temperature and humidity or any other environmental conditions may
render the unit nonoperational as the band may get jammed around the roller
and so on.
3. Please clean the unit often. In particular, it is important to keep the sensor part
and upper cover clean using dry and soft fabrics.
4. Warranty will be void if the unit is tampered with or disassembled by anyone
other than the designated service personnel.
5. Touching the heater when the unit is in operation or within 10 min of the
machine’s shutdown may cause burns and injuries.
6. Ensure that the power is off after using the unit.
* Don’t lift the arch when moving the machine.
2
Product Introduction and Accessories
Automatic banding machine with paper/film YL-420(30)(50),420S
*Easy installation for easy relocation
* Korea’s first rail banding machine
* Compatible of paper and film bands
* Banding without warming up
* Banding without any odor and harmful substances
[Accessories]
Manual: 1 copy
Band: 1 roll
Guide: 1 set
Heater Sheet: 3 pcs
Tool: 1 pc
Power Cable: 1 pc
YL-420(30)
YL-420(50)
YL-420S
3
Part Names and Functions
Arch
2. Feed Button
3. Auto Button
4. Start Button
1. Power Switch
5. Object Sensor
9. Rail
Opening/Closing
Lever
7. Tension Control Knob
Band Reel Cover
6. Temperature
Control Knob
8. Band Set Lever
Front Cover
1. Power Switch
Turn the power ON or OFF.
2. Feed Button
The band is fed to the rail when the red button is pressed.
The RED LED lights up when the band is normally set.
Otherwise, the RED LED blinks.
3. Auto Button
The ORANGE LED lights up, and the auto mode is enabled when the button
is pressed. The ORANGE LED turns off, and manual mode is enabled when it is
pressed again. The machine works in auto banding when the sensor detects
any object in auto mode.
4. Start Button
The GREEN LED lights up, and manual mode is enabled when the power is
turned ON.
5. Object Sensor
It detects an object that is put on the machine for banding, and then the
GREEN LED blinks.
6. Temperature Control Knob
This control knob is used to adjust the heater temperature
for banding.
The heater temperature rises when the control knob
is turned clockwise.
7. Tension Control Knob
This control knob is used to adjust
banding tension, which increases
when the control knob is turned clockwise.
8. Band Set Lever
This lever is used to set the band. Raise the lever, insert the band, and press
the feed button to transfer it to the rail.
9. Rail Opening/Closing Lever
Press or release this lever to open or close the rail respectively.
Open the rail you can remove the band when jammed.
4
Band Installation
4-1) How to feed the band for 420(30)(50)
1) Check the condition of the band.
Cut off the end of the new band with scissors if it is roughly cut, wrinkled, or
contaminated, as such poor conditions may cause a jam.
2) Pull the front cover and band reel cover to open them.
3) Set the band such that the reel rotates clockwise to feed the band, as shown in
the following figures.
4) Raise the band set lever, and then insert the band between the rollers.
5) Close the band reel and front covers.
6) Turn ON the power using the power switch, and press the feed button.
The FEED BUTTON LED lights up when the feed motor runs, and the band is
set.
- If the end of the band becomes damaged, it may have been installed
incorrectly. As such, cut off the end using scissors.
- Make sure to close the band reel cover.
- Pay attention as the adhesive on the start and end of the band roll may cause
a jam and damage the machine.
Caution
band’s direction
4-2) How to feed the band for 420S
1) Check the condition of the band.
Cut off the end of the new band with scissors if it is roughly cut, wrinkled, or
contaminated, as such poor conditions may cause a jam.
2) Turn the toggle switch to OFF.
3) Open the band reel cover and front cover.
4) Turn the band feed lever to widen the gap between the rollers.
5) Insert the band so that the feeding rotation
direction of the band is clockwise as shown
in the figure.
6) While holding the band anti-skid lever
with your hand, insert the band in order
and release the band anti-slip lever again.
(If the band is inserted normally, the band
will rise from the bottom of YL-420 on top.)
7) Close the band feed lever, the band cover, and the front cover.
8) After turning the toggle switch to ON, supply the band.
9) When the band supply is complete, insert the band from ‘6)’ into the YL-420
and press the feed button. At this time, the feed motor rotates and the band is
accurately seated on the rail.
- If the end of the band becomes damaged, it may have been installed
incorrectly. As such, cut off the end using scissors.
- Make sure to close the band reel cover.
- Pay attention as the adhesive on the start and end of the band roll may cause
a jam and damage the machine.
Caution
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere BINDTEC Verpackungsanlagen Handbücher
