8
• Position the tray at the top of the mincing head.
NOZZLE FOR FILLING SAUSAGES (L)
• Press the lock button (C), hold the head and insert it into
the inlet. When inserting, please pay attention that the
head must be slanted as per the arrow indicated on the
top. (Fig. 1). Then move the head anticlockwise so that
the head is fastened tightly. (Fig. 2).
• Insert the screw through the outlet mouth of the mincing
head. (Fig. 3).
• Place the cutting blade in the screw with the cutting edge
pointing to the front. (Fig. 4).
• Insert the cutting plate with the largest holes in the screw,
tting the outlets of the cutting plate in the notches of the
outlet mouth edge of the mincing head. (Fig. 5).
•Insert the nozzle for lling sausages via the xing ring.
(Fig. 7).
•Screw the xing ring tightly in the outlet mouth of the
mincing head, turning clockwise to t the screw, blade
and nozzle. (Fig. 6).
• Position the tray at the top of the mincing head.
ACCESSORYFOR KEBBE (M)
• Press the lock button (C), hold the head and insert it into
the inlet. When inserting, please pay attention that the
head must be slanted as per the arrow indicated on the
top. (Fig. 1). Then move the head anticlockwise so that
the head is fastened tightly. (Fig. 2).
• Insert the screw through the outlet mouth of the mincing
head. (Fig. 3).
• Insert the accessory for base Kebbe in the screw and po-
sition the other Kebbe accessory on top, tting the outlets
in the edge notches of the lling mouth. (Fig. 8).
•Screw the xing ring tightly, turning clockwise to t the
accessories for Kebbe in the screw. (Fig. 6).
• Position the tray at the top of the mincing head.
TOMATO JUICER ACCESSORY (N)
• This accessory permits you to separate the seeds and
pulp of the tomato, to extract the juice.
• Insert the mincing head into the motor body, and secure it
with the xing ring.
• Insert the worm screw through the mouth of the mincing
head. (Fig. 3).
•Insert the tomato accessory, tting the protrusions with
the slots on the edge of the ller neck. Tighten the locking
ring rmly by screwing it clockwise until the accessory ts
into the worm screw. (Fig. 9).
• Fit the pressure control valve, the anti-spatter guard and
the tray for collecting the juice.
REVERSE FUNCTION
• In case of jamming, switch off the appliance by pressing
the switch to the “R” position.
• The screw will rotate in the opposite direction, and the
head will get empty.
• If it does not work, switch off the appliance and clean it.
• Wait for one minute before and after the reverse function.
IF THE MOTOR BLOCKS
• If the motor moves slowly or stops, it could be due to the
food in the blender blocking the chopper. In that case, use
the direction changer switch. To do this, place the ON/
OFF switch in position 0, and press the direction changer
switch. Using the worm screw to perform this operation,
the food will become loose. Pay attention in this inverse
turn situation, as part of the food could come out of the
lling tube/tray. Deactivate the opposite direction turn by
following the previous procedure in reverse.
• If the motor continues to be blocked, unplug the appliance
from the mains and demount its accessories.
CLEANING
• Disconnect the appliance from the mains and allow it to
cool before undertaking any cleaning task.
• Clean the equipment with a damp cloth with a few drops
of washing-up liquid and then dry it.
• Do not use solvents or products with an acid or base pH,
such as bleach, or abrasive products, for cleaning the
appliance.
• Never submerge the appliance in water or any other liquid
or place it under running water.
• During the cleaning process, take special care with the
blades, as they are very sharp.
•It is advisable to clean the appliance regularly and remove
any food that remains.
• Neither parts of this appliance are suitable for cleaning in
the dishwasher.
• Then dry all parts before their assembly and storage.
SERVICE
• Any misuse or failure to follow the instructions for use
renders the guarantee and the manufacturer’s liability null
and void.
ANOMALIESAND REPAIR
• Take the appliance to an authorised technical support
service if problems arise. Do not try to dismantle or repair
without assistance, as this may be dangerous.
