Black Box Agility ACR1002 DP Bedienungsanleitung

Networked linking

Where Agility modules are connected via networked links, you can either congure them individually,

or congure them collectively using an iPATH server:

• Conguring networked Agility modules individually - You need to specify the network

addresses of the Agility modules so that they can locate each other. This can be done using via

OSD on the console connected to the RX unit by pressing CTRL + A LT + C. See rear page.

• Conguring networked Agility modules collectively - The iPATH server allows you to

congure, control and coordinate any number of Agility transmitters and receivers from a single

application. See blackbox.com for details.

Agility ACR1002 DP, FDP and FH-T Extenders

Quick Start

Welcome

This quick start guide covers some of the key points of the Black Box ACR1002DP, ACR1002FDP and

ACR1002FH-T modules. Full user details and setup instructions can be found at www.blackbox.com

Please read the supplied safety instruction leaet before use.

Initial conguration

Agility modules can be linked in two mains ways: Direct or Networked.

Direct linking

Where Agility transmitters and receivers are directly linked to each other, very little conguration

action is required, provided that they both have their factory default settings in place - just link them

together. If the standard settings have been changed in a previous installation, you merely need to

perform a manual factory reset on each unit. Please see the center pages.

IMPORTANT: When using iPATH to congure Agility modules,

it is vital that all units that you wish to locate and control are

set to their factory default settings. Otherwise they will not be

located by the iPATH server. If necessary, perform a manual

factory reset on each Agility unit. See center pages.

Note: If you are using one or more Agility transmitters within

an installation managed by an iPATH server, the iPATH

server must be running rmware version 5.3 or above.

Agility conguration via web pages

Each Agility module hosts its own internal set of web pages which contain all conguration details

and settings.You will need to use a computer connected to the same network as each Agility unit

to access the web pages. Additionally, on the console attached to the receiver unit, you can access

its conguration details via the On Screen Display (OSD) by pressing:

CTRL + A LT + C

To congure Agility modules via their web pages

Run a web browser on your computer and enter the IP address of the required Agility:

The default addresses (if using port 1) are: Transmitter: https://169.254.1.33

Receiver: https://169.254.1.32

The default addresses (if using port 2) are: Transmitter: https://169.254.1.43

Receiver: https://169.254.1.42

The opening page should be displayed:

Full user details and setup instructions can be found at:

www.blackbox.com

MAN-QS-000066 Rev. 1.2

Order toll-free in the U.S. or for

FREE technical support 24/7: Call 877-877-BBOX

(outside U.S. call 724-746-5500)

www.blackbox.com • info@blackbox.com

Connections

To perform a manual factory reset

A factory reset returns the Agility module to its default conguration.

1 Power on the Agility module.

2 Use a long narrow implement (e.g., a straightened-out paper clip) to press-and-hold the recessed

reset button on the front panel for roughly ten seconds until the status indicator turns blue (Note:

alternating red/green indications will occur during the ten second period while the button is still pressed).

3 Release the reset switch. The indicator will change to red for a short time (less than ten seconds)

and then back to blue while the Agility module performs the reset and should then change to an

alternative color, usually orange initially, signifying that the operation is complete.

Note: If you are performing a factory reset and intend to disconnect the power immediately after the reset,

you must wait at least 30 seconds after you have released the reset button for it to complete the process.

Teaming

Agility modules are ready to automatically invoke teaming whenever

the primary and secondary ports are both used to link transmitters

and receivers. Teaming potentially doubles the available bandwidth for

video intensive applications and also provides redundancy in case one

link is lost.

The units benet from multiple audio signal streams:

• Uni-directional analog audio - from the host

PCs jack socket,

• Uni-directional digital audio - via the video

connection,

• Bi-directional digital audio - via the USB

connection (converted to/from analog).

Main status indicators

Green All services present.

Amber Running but video, USB or network link missing.

Red Booting before processor loaded or failed.

Red rapid ash Critical error has been detected (a message will

also be displayed within the OSD.)

Blue Factory reset mode active.

Red/green ash Booting into factory recovery mode.

Green/blue ash Upgrade mode active.

Fast green ash Identify mode active.

* ACR1002FDP variants have 2x SFP sockets and no

in-built CATx ports.

** ACR1002FH-T variants have 2x HDMI®video ports.

Dieses Handbuch passt für folgende Modelle

Andere Black Box Extender Handbücher

Black Box

Black Box IC244A-R2 Bedienungsanleitung

Black Box

Black Box ICU544A Bedienungsanleitung

Black Box

Black Box ACU1500A-R3 Bedienungsanleitung

Black Box

Black Box AC1000A-R3 Bedienungsanleitung

Black Box

Black Box LMC5178A Bedienungsanleitung

Black Box

Black Box KVX Series Gebrauchsanweisung

Black Box

Black Box IC280A-R2 Bedienungsanleitung

Black Box

Black Box ServSwitch ACU2500A Bedienungsanleitung

Black Box

Black Box Abeo G.703 LAN Montage- und Bedienungsanleitung

Black Box

Black Box LB510A Bedienungsanleitung

Black Box

Black Box ACX1MT Series Bedienungsanleitung

Black Box

Black Box KVX HP Series Bedienungsanleitung

Black Box

Black Box ServSwitch ACU1001A Bedienungsanleitung

Black Box

Black Box ServSwitch ACU5114A Bedienungsanleitung

Black Box

Black Box AVU4001A Bedienungsanleitung

Black Box

Black Box LWE100A Bedienungsanleitung

Black Box

Black Box ServSwitch ACU5116A Bedienungsanleitung

Black Box

Black Box VX-1001-RX Bedienungsanleitung

Black Box

Black Box ServSwitch ACU1001A Bedienungsanleitung

Black Box

Black Box ACX1T Series Bedienungsanleitung

Black Box

Black Box LB320A Bedienungsanleitung

Black Box

Black Box ACU5600A-SM Bedienungsanleitung

Black Box

Black Box IC406A Bedienungsanleitung

Black Box

Black Box ServSwitch Wizard ACU5012A Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung