Black Box Industrial Control MDU20G-918 Bedienungsanleitung

Industrial Control Modem GSM

Quick Start Guide

TECHNICAL:

SALES:

FAX:

ADDRESS:

WEB:

(0118) 965 6000

(0118) 965 5100

(0118) 965 5001

464 Basingstoke Road, Reading, Berkshire RG2 0QN

www.blackbox.co.uk

Industrial Control Modem GSM 900/1800MHz:

MDU20G-918

Magnetic Aerial:

MDU21-MAG

Roofmount Antenna:

MDU21-ROOF

Standard Antenna:

MDU21-STD

Industrial Control Modem GSM

SALES: 0118 965 5100

How To Contact your Local Black Box

Italy: Australia:

Black Box Italia S.P.A Black Box Catalog Australia PTY LTD

Tel: 0227400280 Tel: 0398797100

Fax: 0227400219 Fax: 0398702955

Web Site: www.blackbox.it

Deutschland: Brazil:

Black Box Deutschland Black Box Do Brasil.

Tel: 0811/5541-0 Tel: (011) 5515-4000

Fax: 0811/5541-499 Fax: (011) 5515-4002

Web Site: www.blackbox-deutschland.com Web Site: www.blackbox.com.br

Switzerland: Canada:

Datacom Black Box Services AG Black Box Canada Corp.

Tel: 0554517070 Tel: 0416-736-8000

Fax: 0554517075 Fax: 0416-736-7348

Web Site: www.black-box.ch Web Site: www.blackbox.com

Netherlands: Mexico:

Black Box Datacom BV Black Box De Mexico S.A. de C.V

Tel: 03032417799 Tel: 05-420-0100

Fax: 0302414746 Fax: 05-420-0123

Web Site: www.blackbox.nl/ Web Site: www.blackbox.com.mx

Belgium: Japan:

Black Box Black Box Catalog

Tel: 027258550 Tel: 03-3820-5011

Fax: 027259212 Fax: 03-3820-5010

Web Site: www.blackbox.be Web Site: www.blackbox.co.jp/

Industrial Control Modem GSM

TECHNICAL: 0118 931 2233

France: U.S.A

Black Box Catalogue Black Box Corporation

Tel: 0145606700 Tel: 724-746-5500

Fax: 0145606747 Fax: 724-746-0746

Web Site: www.blackbox.fr Web Site: www.blackbox.com

Spain: Chile

Black Box Comunicaciones S.A. Black Box Chile

Tel: 34 91 663 0200 Tel: 00 562 223 8811

Fax: 34 91 661 84 35 Fax: 00 562 225 1002

Web Site: www.blackbox.es Web Site: www.Blackbox.cl

Industrial Control Modem GSM

SALES: 0118 965 5100

Contents

Introduction..............................................................................................................................................5

Package Contents......................................................................................................................5

GSM Network Connection.......................................................................................................................6

Configuration...........................................................................................................................................7

Test Commands.......................................................................................................................11

Informative Commands.............................................................................................................11

Industrial Control Modem GSM

TECHNICAL: 0118 931 2233

Introduction

Congratulations on purchasing one of the best GSM Data Terminals available today. The

Industrial Control Modem GSM will provide reliable service, provided it is connected to an

appropriate GSM Network and configured correctly. This booklet will guide you through

these stages.

Package Contents

Packed in with the GSM Data Terminal you will find a diskette, this contains three files, this

booklet, the User Guide and a manual of AT Commands, all in PDF format.

Industrial Control Modem GSM

SALES: 0118 965 5100

GSM Network Connection

It is up to you to choose which GSM Network you would like to use, but please be aware that

there are three different frequencies used for GSM communications, 900, 1800 and 1900

Mhz. For instance in the UK, Vodaphone and Cellnet use 900Mhz and One to One and

Orange use 1800Mhz. You should order your data terminal to match the Network you plan

to use. A list of GSM Networks and their frequencies is available on page 118 of the AT

Commands manual, but please check with your Network Provider to confirm that no changes

have been made.

When opening your GSM account please ask your Network Provider for a Data Account.

Data Accounts usually have a much lower monthly charge than Audio Accounts.

Regardless of the type of account you have, Data or Audio, you must ensure that the SIM

card you receive is DATA ENABLED. Even if you have a Data Account, please check to

confirm that it has been Data Enabled, sometimes this is not done automatically.

You will normally receive three telephone numbers will each account, one for Audio

(probably won’t work on a Data Account), one for Fax and one for Data. Obviously the Data

number is the one to use. If you do not have a separate Data number please confirm with

your Network Provider that the number you have is a Data number. The reason for this

additional numbering is that not all the analogue fixed-line exchanges/switches can process

and route the digital data that the digitally-based GSM networks use. Thus the digital data

must be fed through an appropriate incoming voice, data, or fax number.

Once you are satisfied that you have an Enabled Data Account, please check that the SIM

card PIN number is not enabled. To do this place the SIM card in a normal GSM phone and

check that the need to insert the PIN number, when the power is switched on, is disabled.

You may now place the SIM card in your Industrial Control Modem GSM, power it up and

check the Network connection (refer to Users Manual). On power up the LED on the front

of the unit will be lit steady, this means power is on, but no Network Connection is available.

After a short period of time the LED will start to flash, short time lit and longer time dark,

this means a Network Connection is established.

Industrial Control Modem GSM

TECHNICAL: 0118 931 2233

Configuration

As with other types of modem the Industrial Control Modem GSM has many different

configurations available, possibly only one of which will be suitable for your application.

The factory default configuration is a general-purpose type, which will work with many

different types of equipment, but you may need to adjust some settings. In most cases only a

few changes may be necessary and the most common are outlined below:

You should be aware of two terms, which are used extensively in Data Communications,

DTE (Data Terminal Equipment) and DCE (Data Communications Equipment).

PCs, industrial controllers and telemetry outstations are normally DTEs and modems are

normally DCEs.

The Industrial Control Modem GSM is a DCE and the device to which you connect it will

almost certainly be a DTE.

In the text below the Industrial Control Modem GSM will now be referred to as the DCE and

your Connected Equipment as the DTE.

AT Commands

The Industrial Control Modem GSM (DCE) is Hayes compatible, meaning that it uses Hayes

type AT commands. For setting up the configuration, these commands can either be loaded

into its internal memory or can be given to the unit, by its connected equipment (DTE), in the

form of an initialisation string.

AT commands always start with “AT”and several commands can be given in one command

string, provided the string does not exceed 40 characters. For instance the default

initialisation string used in a RTU8 Telemetry Outstation is AT&C1E0V0S0=1. A full

explanation of these parameters is given in the AT Commands manual, but the most

commonly used, and therefore the most likely you will have to adjust are:

Command Explanation

ATVn Result codes in numerical or verbose form.

V0 numerical, 0,1, etc.

V1 verbose, OK, ERROR, etc.

Check which type of result code your DTE requires.

AT&Cn Carrier Detect

&C0 DCD is always active

&C1 DCD is active if modem is on line

Data Carrier Detect (DCD) is a hardware signal that notifies the DTE that the DCE is in

communication with another modem. Some software will not start-up properly if the DCD is

active. Default is &C1.

Industrial Control Modem GSM

SALES: 0118 965 5100

AT&Dn Data Terminal Ready settings

&D0 Modem ignores DTR

&D1 Modem switches from data to command mode

when DTR switches from ON to OFF

&D2 Upon DTR switch from ON to OFF, the call is

cleared down

AT+IFC Defines if Flow Control is used between DTE and DCE.

+IFC=0,0 No flow control

+IFC=2,2 RTS flow control (preferred)

Flow control is the use of RS232 signals to start and stop the flow of data to avoid data loss

during buffering. Check if your DTE supports RTS/CTS flow control (Hardware flow

control). With Flow Control the DTE will send data to the DCE. The DCE will store this

data in a buffer. When this buffer is full, the DCE will drop the CTS-line, telling the DTE

that it has to stop transmitting data until the signal raises again. If the RTS-signal is OFF,

transmitting data to the DTE is stopped until the signal switches to ON.

AT+IPR Defines the Baud rate used for communications between the DTE and DCE.

AT+IPR=0 The Baud rate is selected automatically

AT+IPR=9600 The Baud rate is fixed at 9600 baud or another speed.

This is best left at its default setting of 0 (auto), unless your DTE demands

otherwise.

AT+CBST Defines the type of Bearer to be used. That is the communication between

the DCE and the GSM Network.

AT+CBST=0,0,0 Auto baud rate selection, transparent mode

AT+CBST=0,0,1 Auto baud rate selection, non-transparent mode

AT+CBST=7,0,0 9600 (V32) baud rate selected, transparent mode

AT+CBST=4,0,1 2400 (V24bis) baud rate selected, non-transparent mode

Usually the baud rate is best left in the default Auto selection. Non-transparent copes with

bad connections better than transparent mode, but transparent mode will pass data more

quickly. Try either to see which is best for your application.

Non-Transparent communication utilises a special GSM network-based error correction

facility called "Radio Link Protocol" (RLP) that ensures a more robust transmission. What

this essentially means is that the GSM network will add special error correction codes to

control the flow of data.

This ensures that the data transmitted first obtains a special acknowledgement signal from the

receiver that informs the transmitter that the data has been received as transmitted and that

the receiver is ready to receive the next set of data from the transmitter. If there is no such

acknowledgement signal from the receiver, the networks will utilise their "data buffering"

feature by using a special "forward correction" technique to ensure uninterrupted data

transmission throughout.

Industrial Control Modem GSM

TECHNICAL: 0118 931 2233

With transparent data transmission GSM error correction is not applied, over the air interface.

AT+ICF This command is used to determine the local serial port start-stop

(asynchronous) character framing that the DCE shall use. If your

application requires something other than the normal 8 data bits, 1 stop

bit and no parity, you may use this command to make the change. See

AT Command manual

for full details.

ATEn Defines if the DCE echoes (sends back) characters to the DTE.

ATE0 Characters are not echoed

ATE1 Characters are echoed Check which your DTE requires

ATS0=n Defines whether the DCE should answer incoming calls automatically.

ATS0=0 Incoming calls not answered

ATS0=1 Incoming calls answered after 1 ring

ATS0=5 Incoming calls answered after 5 rings

The default is 0, therefore if incoming calls are to be answered this point must be changed.

Usually set to 1. Note - make sure you use a 0 (zero) after the S and not a letter O.

If your DTE will not work with the default configuration in the Industrial Control Modem

GSM, remembering that the ATS0 command must be changed if incoming calls are to be

answered, the above are the most likely parameters that may need changing. Experience

suggests that only one or two points may need to be changed. You will need information

from the manufacturer of your Connected Equipment (DTE) in order to configure the

Industrial Control Modem GSM (DCE) correctly. Ask for advice on each of the above

commands.

If you wish to give the DCE these commands via an initialisation string, from the DTE, either

on power up and/or when a call is to be made, then they may be made in the normal manner,

such as:

AT +IPR=0 +CBST=0,0,1 &C1 E0 V0 S0=1

Note. The spaces have been inserted for clarity and need not be placed in the string. Again

for clarity we suggest that upper case is used.

If you wish to store the configuration permanently in the Industrial Control Modem GSM

(DCE) then you may use a PC terminal programme, such as HyperTerminal (supplied with

Windows) as follows.

Start HyperTerminal, name the new connection and hit OK. In the next pop-up box go to

“Connect using”and select “Direct to Com1”, assuming you are using Com1. Hit OK.

On next pop-up box go to “Bits per second”and select 9600, leave all other parameters as

they are. Hit OK.

Industrial Control Modem GSM

SALES: 0118 965 5100

You will now have a screen via which you can communicate with the DCE, BUT NOT

BEFORE YOU HAVE TURNED ON THE CAPS LOCK. Please make sure you do this.

Now type AT and return. The DCE will respond with OK.

If the DCE responds with a 0 or 1, enter ATV1 and return, you will then get an OK. (See

ATV command above)

If you can’t see what you type, carefully enter ATE1 and return. Text should then appear.

(See ATE command above)

You are now ready to talk to the DCE.

Configuration commands are simply entered thus:

ATS0=1 [return]

OK (response from DCE)

Each command can be entered in this way, making sure that the DCE responds with an OK

after each carriage return. OK means the command has been accepted. If the DCE responds

with “ERROR”, the command has not been accepted and you should re-enter it, carefully

checking your syntax.

Your screen could then look like:

When you have finished entering your configuration commands you need to store them in the

memory of the DCE. To do this enter:

AT&W

You have now configured the DCE.

There are some other useful commands you can use to obtain information or test the DCE:

AT+CBST=0,0,1

AT+IPR=0

ATS0=1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Black Box Modem Handbücher

Black Box

Black Box ME0005A-10BT Bedienungsanleitung

Black Box

Black Box ME778C-RJ45 Bedienungsanleitung

Black Box

Black Box MD5010A Bedienungsanleitung

Black Box

Black Box USB Director RS-232 Bedienungsanleitung

Black Box

Black Box MD1276A Bedienungsanleitung

Black Box

Black Box ME759C-RJ11 Bedienungsanleitung

Black Box

Black Box SHM-NPR Plus Series Bedienungsanleitung

Black Box

Black Box LES1204A-3G Bedienungsanleitung

Black Box

Black Box MD3400A Bedienungsanleitung

Black Box

Black Box ME800A Plus Bedienungsanleitung

Black Box

Black Box ME109A Bedienungsanleitung

Black Box

Black Box Compact mDSL Modem Bedienungsanleitung

Black Box

Black Box MDU9705A-V35 Bedienungsanleitung

Black Box

Black Box High Speed SHM-B Async Bedienungsanleitung

Black Box

Black Box 32144 Bedienungsanleitung

Black Box

Black Box ME657A-M/F Bedienungsanleitung

Black Box

Black Box MD1276A Bedienungsanleitung

Black Box

Black Box ME760A-R2 Bedienungsanleitung

Black Box

Black Box MAY 1994 Bedienungsanleitung

Black Box

Black Box MD1970A Bedienungsanleitung

Black Box

Black Box ME795A Bedienungsanleitung

Black Box

Black Box MD885A-R4 Bedienungsanleitung

Black Box

Black Box ME0002A-V35 Bedienungsanleitung

Black Box

Black Box MD1620A Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung