Black Box Speedster 288 Bedienungsanleitung

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

OCTOBER 1996

MD361C-PC

Speedster 288 Internal Fax/Modem

SPEEDSTER 288 INTERNAL FAX/MODEM

TRADEMARKS USED IN THIS MANUAL

MNP is a registered trademark of Microcom Systems, Inc.

Windows is a registered trademark of Microsoft Corporation.

UL is a registered trademark of Underwriters Laboratories Incorporated.

All applied-for and registered trademarks are the property of their respective owners.

REGULATORY INFORMATION

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENT

Class B Digital Device. This equipment has been tested and found to comply with the

limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference

in a residential installation. However, there is no guarantee that interference will not

occur in a particular installation. This equipment generates, uses, and can radiate

radio frequency energy, and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. If this

equipment does cause harmful interference to radio or telephone reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult an experienced radio/TV technician for help.

Caution:

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

To meet FCC requirements, shielded cables and power cords are required to connect

this device to a personal computer or other Class B certified device.

This digital apparatus does not exceed the Class B limits for radio noise emission from digital

apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de classe B prescrites dans le Règlement sur le brouillage

radioélectrique publié par Industrie Canada.

See the bottom of your modem board for the FCC ID code and the FCC 68 number.

Ringer Equivalence: 0.4B

SPEEDSTER 288 INTERNAL FAX/MODEM

NORMAS OFICIALES MEXICANAS (NOM)

ELECTRICAL SAFETY STATEMENT

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes

de que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para

referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones

de operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,

cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales

que sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá

a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser

referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,

alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en

libreros o gabinetes que impidan el flujo de aire por los orificios de ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor

como radiadores, registros de calor, estufas u otros aparatos (incluyendo

amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del

tipo descrito en el instructivo de operación, o como se indique en el aparato.

REGULATORY INFORMATION

12. Precaución debe ser tomada de tal manera que la tierra fisica y la

polarización del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo

particular atención a los contactos y receptáculos donde salen del aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos

de las lineas de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo

no sea usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos

no sean derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra

un cambio en su desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

UL LISTING/CSA APPROVAL

This equipment is UL®listed and CSA approved for the uses described in this manual.

SPEEDSTER 288 INTERNAL FAX/MODEM

CABLE REQUIREMENTS

The connection from the modem to the computer must be made with a high-quality,

shielded cable to ensure compliance with FCC limits.

CONNECTING TO THE TELEPHONE COMPANY

It is not necessary to notify the telephone company before installing the modem.

However, the telephone company may request the telephone number(s) to which

the Speedster 288 is connected and the FCC information.

Be sure that the telephone line you are connecting the modem to is a standard

analog line and not a digital (PBX), party, or coin telephone line.

If the modem is malfunctioning, it may affect the telephone lines. In this case,

disconnect the modem until the source of the difficulty is traced.

FOR CANADIAN MODEM USERS

NOTICE: The Industry Canada (IC) label identifies certified equipment. This

certification means the equipment meets certain telecommunications network

protective, operational, and safety requirements. The Department does not

guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The equipment

must also be installed using an acceptable method of connection. In some cases, the

company’s inside wiring associated with a single-line, individual service may be

extended by means of a certified connector assembly (telephone extension cord).

The customer should be aware that compliance with the above conditions may not

prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian

maintenance facility designated by the supplier. Any repairs or alterations made by the

user to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the equipment.

REGULATORY INFORMATION

Users should ensure for their own protection that the electrical ground connections of

the power utility, telephone lines, and internal metallic water pipe system, if present,

are connected together. This precaution may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves, but

should contact the appropriate electric inspection authority, or electrician, as

appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage of

the total load to be connected to the telephone loop which is used by the device, to

prevent overloading. The termination on a loop may consist of any combination of

devices, subject only to the requirement that the total of the Load Numbers of all the

devices not exceed 100.

The Load Number is located on the bottom of your modem.

AVIS: L’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette

certifie que le matériel est conforme à certaines normes de protection, d’exploitation

et de sécurité des réseaux de télécommunications. Toutefois, le Ministère n’assure pas

que le matériel fonctionnera a la satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit assurer qu’il soit permis de le raccorder

aux installations de l’entreprise locale de télécommunications. Le matériel doit

également être installé en suivant une méthode acceptée de raccordement. Dans

certains cas, les fils intérieurs de l’entreprise utilisés pour un service individuel à ligne

unique peuvent être prolongés au moyen d’un dispositif de raccordement homologué

(cordon rallonge téléphonique interne). L’abonné ne doit pas oublier qu’il est

possible que la conformité aux conditions énoncées ci-dessus n’empechent pas la

dégradation du service dans certaines situations. Actuellement, les entreprises de

télécommunication ne permettent pas que l’on raccorde leur matériel à des jacks

d’abonné, sauf dans les cas précis prévus par les tarifs particuliers de ces entreprises.

Les réparations de matériel homologué doivent être effectuées par un centre

d’entretien canadien autorisé désigné par le fournisseur. La compagnie de

télécommunications peut demander à l’utilisateur de débrancher un appareil à la

suite de réparations ou de modifications effectuées par l’utilisateur, ou à cause de

mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre

de la source d’énergie électrique, des lignes téléphoniques et des canalisations d’eau

métalliques, s’il y en a, soient raccordés ensemble. Cette précaution est

particulièrement importante dans les régions rurales.

SPEEDSTER 288 INTERNAL FAX/MODEM

AVERTISSEMENT: L’utilisateur ne doit pas tenter de faire ces raccordements

lui-meme; il doit avoir recours aux services d’un électricien.

L’indice de charge (IC) assigné à chaque dispositif terminal indique, pour éviter

toute surcharge, le pourcentage de la charge totale qui peut être raccordée à un

circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé

peut être constituée de n’importe quelle combinaison de dispositifs, pourvu que la

somme des indices de charge de l’ensemble des dispositifs ne dépasse pas 100.

L’indice de charge se trouve sur le modem.

CONTENTS

Contents

Chapter Page

1. Specifications..............................................................................................10

2. Introduction ..............................................................................................11

2.1 Description ........................................................................................11

2.1.1 How a Modem Works ..........................................................11

2.1.2 How Your Speedster 288 Internal

Fax/Modem Works..............................................................11

2.2 Package Contents ..............................................................................12

2.3 What You’ll Need ..............................................................................12

3. Installation ..................................................................................................13

3.1 Plug and Play Installation..................................................................13

3.1.1 If You Are Using Plug and Play ..........................................14

3.1.2 If You Are Not Using Plug and Play....................................15

3.2 Installing the Modem ........................................................................16

3.3 Configuring with Windows 95 ..........................................................18

3.4 Installing Your Software ....................................................................19

4. Communications Software ........................................................................20

4.1 Configuring Your Modem ................................................................20

4.2 Configuring Your Software ..............................................................20

4.3 Testing Your Installation ..................................................................21

5. Commands..................................................................................................22

5.1 Typing in Commands........................................................................22

5.2 AT Commands ..................................................................................23

5.3 S-Registers ..........................................................................................31

6. Troubleshooting ........................................................................................40

6.1 Before the Modems Connect............................................................40

6.2 During Data Transfer ........................................................................41

6.3 Calling Black Box ..............................................................................44

6.4 Shipping and Packaging....................................................................44

SPEEDSTER 288 INTERNAL FAX/MODEM

Standards Supported — Bell 103/V.21, Bell 212A/V.22, ITU-TSS Group III

fax, V.22 bis, V.32 bis, V.34, V.32, V.23, V.FC, V.34+, V.25, V.27, V.29, V.42,

V.42 bis

Modem Data Rate — 33.6 Kbps

Operation — Full duplex

Compliance — UL, FCC Class B, CSA

Ringer Equivalency — 0.4B

Diagnostics — Standard AT&T0 through AT&T8 commands

Connectors — (2) RJ-11: Phone and Line

Error Correction — MNP®2 through 5; V.42/42 bis

Command Mode — AT Commands

Modem Type — Data/Fax

Line Type — 2-wire dial

Clocking — Asynchronous

Fax Class Type — V.17, V.29, V.27 Group III

Fax Operation — 2-wire half-duplex

Fax Rate — 14.4 Kbps

Operating Temperature — 32 to 113°F (0 to 45°C)

Operating Humidity — 10 to 85%, noncondensing

Power Source — PC bus

Size — Half card

1. Specifications

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Black Box Modem Handbücher

Black Box

Black Box ME0006A-10BT Bedienungsanleitung

Black Box

Black Box MWU2000-G703 Bedienungsanleitung

Black Box

Black Box ME758C-RJ11 Bedienungsanleitung

Black Box

Black Box MD1620A Bedienungsanleitung

Black Box

Black Box Sync/Async Fiber Optic Modem Bedienungsanleitung

Black Box

Black Box ME375A Bedienungsanleitung

Black Box

Black Box MC119A Bedienungsanleitung

Black Box

Black Box MDS931AE-2 Bedienungsanleitung

Black Box

Black Box ME0005A-10BT Bedienungsanleitung

Black Box

Black Box MEG101AE-R4 Bedienungsanleitung

Black Box

Black Box ME0002A-V35 Bedienungsanleitung

Black Box

Black Box MD1276A Bedienungsanleitung

Black Box

Black Box USB Director RS-232 Bedienungsanleitung

Black Box

Black Box ME475A Bedienungsanleitung

Black Box

Black Box SHM-NPR Plus Series Bedienungsanleitung

Black Box

Black Box ME475A-R2 Bedienungsanleitung

Black Box

Black Box MD1970A Bedienungsanleitung

Black Box

Black Box High Speed SHM-B Async Bedienungsanleitung

Black Box

Black Box ME800A Plus Bedienungsanleitung

Black Box

Black Box ME800A-PLUS-R2 Bedienungsanleitung

Black Box

Black Box ME935A Bedienungsanleitung

Black Box

Black Box 32144 Bedienungsanleitung

Black Box

Black Box ME778C-RJ45 Bedienungsanleitung

Black Box

Black Box MD1620A Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung