Black Box IC052 Bedienungsanleitung

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

FEBRUARY 1996

IC052 IC075A

IC052E IC075AE

IC053 IC076A

IC053E IC076AE

3X Repeater—UTP

3X Repeater—UTP RJ-45

3X Repeater—Fiber

3X Repeater—Fiber RJ-45

3X REPEATER-FIBER

OPTIC LINK

POWER SYNC

CTRL TERM

SYNC

3X REPEATER-UTP

POWER

TERM

SYNC

CTRL

SYNC

FCC STATEMENT

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio frequency energy

and if not installed and used properly, that is, in strict accordance with the

manufacturer’s instructions, may cause interference to radio communication.

It has been tested and found to comply with the limits for a Class A

computing device in accordance with the specifications in Subpart J of Part 15

of FCC rules, which are designed to provide reasonable protection against

such interference when the equipment is operated in a commercial

environment. Operation of this equipment in a residential area is likely to

cause interference, in which case the user at his own expense will be required

to take whatever measures may be necessary to correct the interference.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission from

digital apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de classe A prescrites dans le Règlement sur le

brouillage radioélectrique publié par Industrie Canada.

TRADEMARKS

IBM®and AS/400®are registered trademarks of IBM Corporation.

All applied-for and registered trademarks are the property of their respective

owners.

INSTRUCCIONES DE SEGURIDAD

NORMAS OFICIALES MEXICANAS (NOM)

ELECTRICAL SAFETY STATEMENT

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes

de que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para

referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de

operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,

cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,

etc..

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales

que sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como

sea recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más

allá a lo descrito en las instrucciones de operación. Todo otro servicio

deberá ser referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama,

sofá, alfombra o superficie similar puede bloquea la ventilación, no se

debe colocar en libreros o gabinetes que impidan el flujo de aire por los

orificios de ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de

calor como radiadores, registros de calor, estufas u otros aparatos

(incluyendo amplificadores) que producen calor.

NOM STATEMENT

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo

del tipo descrito en el instructivo de operación, o como se indique en el

aparato.

12. Precaución debe ser tomada de tal manera que la tierra fisica y la

polarización del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos,

poniendo particular atención a los contactos y receptáculos donde salen

del aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las

lineas de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no

sea usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean

derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del

aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su

desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

3X Repeater

CONTENTS

1. Specifications ...................................................................................7

2. Introduction.....................................................................................8

2.1 UTP Repeaters...........................................................................8

2.2 Fiber Repeaters..........................................................................8

3. Installation—UTP Repeaters ..........................................................9

3.1 General ......................................................................................9

3.2 Preliminary ................................................................................9

3.3 Procedure ..................................................................................9

4. Installation—Fiber Repeaters .........................................................11

4.1 General ......................................................................................11

4.2 Preliminary ................................................................................11

4.3 Procedure ..................................................................................11

5. Jumper Settings................................................................................13

6. Operation and Troubleshooting ....................................................15

6.1 Normal Operation.....................................................................15

6.2 Problem-Solving Checklist........................................................15

CHAPTER 1: Specifications

Maximum

distance — Controller to repeater: 2250 ft. (685.8 m)

Repeater to workstation: 2250 ft. (685.8 m)

Repeater to daisychained repeater: 8200 ft. (2499.4 m)

Devices — IBM®5251, 5291, 5292, 3180-12, 3196, and

compatible terminals used in a 3X or AS/400®system

Speed — 1 Mbps

Cable

Requirements — IC052, IC052E, IC075A, IC075AE: 22- or 24-gauge solid

copper unshielded twisted pair;

IC053, IC053E, IC076A, IC076AE: Dual-fiber,

multimode graded, 50 or 62.5 micron fiberoptic

Configuration — Pin 3 ring, Pin 4 tip

Connectors — IC052, IC052E: (2) RJ-11 female, (2) pairs screw-type

terminals

IC053, IC053E: (1) RJ-11 female, (1) pair screw-type

terminals, (2) ST connectors

IC075A, IC07AE: (2) RJ-45 female, (2) pairs screw-type

terminals

IC076A, IC076AE: (1) RJ-45 female, (1) pair screw-type

terminals, (2) ST connectors

Indicators — LEDs: (1) power, (2) line sync

Temperature — Storage: -4 to 185° F (-20 to 85° C);

Operating: 50 to 104° F (10 to 40° C)

Humidity — 95%, noncondensing

Power — IC052, IC053, IC075A, IC076A: 110 VAC;

IC052E, IC053E, IC075AE, IC076AE: 220 VAC

Size — 1.3”H x 8.5”W x 4”D (3.3 x 21.6 x 10.2 cm)

Weight — 2 lb. (0.9 kg)

1. Specifications

3X Repeater3X Repeater—Fiber

Your 3X and AS/400 signals cover much longer distances with a 3X Repeater

on line. The Repeater carries out all the vital functions for retransmission—

each signal is resynchronized, reformatted, and filtered for noise before it is

passed on.

2.1 UTP Repeaters

Four models are available:

• 3X Repeater—UTP (IC052) with 110 VAC power supply

• 3X Repeater—UTP (IC052E) with 220 VAC power supply

• 3X Repeater—UTP RJ-45 (IC075A) with 110 VAC power supply

• 3X Repeater—UTP RJ-45 (IC075AE) with 220 VAC power supply

With a single Repeater on your lines, you can set your workstation up to

4500 feet (1376.1 m) from your controller. Each additional Repeater adds

2250 feet (685.8 m) to your line, up to the maximum distance, as determined

by the response time of your system.

The Repeater can handle screw terminal or RJ-11 connections, and works

with 22- or 24-AWG unshielded twisted pair.

2.2 Fiber Repeaters

Four models are available:

• 3X Repeater—Fiber (IC053) with 110 VAC power supply

• 3X Repeater—Fiber (IC053E) with 220 VAC power supply

• 3X Repeater—Fiber RJ-45 (IC076A) with 110 VAC power supply

• 3X Repeater—Fiber RJ-45 (IC076AE) with 220 VAC power supply

Repeaters work in pairs. You can locate each repeater up to 2250 feet

(658.8 m) from its controller or terminal, while your Repeaters may be

separated from each other by distances of up to 8200 feet (2499.4 m).

You can also cascade Repeaters to drive signals even further. Each

additional Repeater adds 8200 feet to your line.

The Repeater uses 50-, 62-, or 100-micron fiberoptic cable terminated by

ST connectors. For workstation and controller connections, it can handle

screw terminal or RJ-11 connections, and works with 22- or 24-AWG twisted

pair.

2. Introduction

CHAPTER 3: Installation—UTP Repeaters

3.1 General

Before you install your Repeater, check the contents of the carton. In

addition to this manual, the package should contain an undamaged Repeater

unit. If it has been damaged, call your sales representative for a replacement.

When you install the Repeater, you should follow all customary precautions

for working with electrical equipment. Make sure there’s no current flowing

within your workstation, your controller, and your cable by shutting off power

to your devices before you begin.

The site requirements for the Repeater are minimal. It should sit in a flat,

stable, dry site that affords ample clearance for all connections, and has an

AC outlet within 6 feet (1.8 m).

3.2 Preliminary

To get the best performance from your repeater, you should check the

following:

• Your cable. It should not have any bridge taps, and the wires of the twisted

pairs should be grouped, not separated. You should avoid using flat silver

satin cable for long-distance runs — it is highly vulnerable to noise and

may cause intermittent problems with transmissions.

If you use multi-pair cable, you should use bulk lengths of 100 feet

(30.5 m) or more, and you should avoid connecting multiple services

under the same sheath.

• Polarity. You should make sure that wiring polarity between the host

and your workstations is straight-through. The Repeater is sensitive

to polarity reversals.

• Termination. The last workstation on the host should be properly

terminated.

• Configuration. Your system should be able to recognize all the

devices that are on-line.

3.3 Procedure

After you have checked your site, set your Repeater in place—no more than

2250 feet (685.8 m) from your controller, and no more than 2250 feet from

your workstation.

Make sure you can distinguish between the tip lead and the ring lead on

the balun that leads to your controller. When you attach your cables to the

repeater, the tip lead of the balun will contact the tip lead of the connector

marked “CTRL,” while the ring lead of the balun will contact the ring lead of

the same connector. The same arrangement will hold for the balun that leads

to your terminal, and the connector marked “TERM.”

3. Installation—UTP Repeaters

3X Repeater3X Repeater—FIber

Plug the Repeater into your outlet. The green LED, marked “Power,”

should glow. If it does not, check your power supply, and then check

with your technical representative.

At this point, you should follow the steps given under one of the two

headings below, depending on which attachment method you prefer.

Figure 1 applies to both methods.

To Use Screw Terminal Connectors

1. Strip 1/4” of insulation from both lengths of twisted-pair wire

(controller and workstation)

2. Connect the wires coming from the controller to the block marked

“CTRL” and tighten the locking screws.

3. Connect the wires coming from the workstation to the block marked

“TERM” and tighten the locking screws.

4. Check that the tip and ring contacts have not been crossed.

5. Turn on your workstation. The “CTRL-SYNC” and “TERM-SYNC”

LEDs should flash.

6. Your unit now should be operational. You should see the sign-on screen

from your system.

To Use Modular Connectors

1. Use 22- or 24-AWG twisted pair, with RJ-11 jacks attached, to connect

the cables as shown in Fig. 1.

2. Check to make sure that the tip and ring contacts have not been crossed.

3. Turn on your workstation. The “CTRL-SYNC” and “TERM-SYNC” LEDs

should flash.

4. Your unit now should be operational. You should see the sign-on screen

from your system.

RING TIP (T)

(R)

POWER SYNC

TERM

RINGTIP (T) (R)

CTRL

SYNC

Fig. 3-1. Cabling the Repeater.

CHAPTER 4: Installationn—Fiber Repeaters

4. Installation—Fiber Repeaters

4.1 General

Before you install your Repeater pair, check the contents of the shipping

cartons. In addition to this manual, each package should contain an

undamaged Repeater unit. If it has been damaged, call your sales

representative for a replacement.

When you install the pair, follow all customary precautions for working

with electrical equipment. Make sure there’s no current flowing within your

workstation, your controller, and your cable by shutting off power to your

devices before you begin.

The site requirements for your Repeaters are minimal. They should sit

in a flat, stable, dry site that affords ample clearance for all connections,

and AC outlets should lie within 6 feet (1.8 m).

4.2 Preliminary

To get the best performance from your Repeater pair, you should check

the following:

• Your cable. Your fiberoptic cable and the cable that leads from your

controller and workstation should be in top condition, with all connectors

secure and no breaks. You should not use flat silver satin cable for your

controller or terminal connections, since it is highly susceptible to noise.

• Polarity. You should make sure that wiring polarity for your Repeaters

is straight-through. They are sensitive to polarity reversals.

• Termination. The last workstation on the host should be properly

terminated.

• Configuration. Your system should be able to recognize all the devices

that are on-line.

4.3 Procedure

After you have checked your site, set your Repeaters in place—no more than

2250 feet (685.8 m) from your controller, no more than 2250 feet from your

workstation, and no more than 8200 feet from each other.

Make sure you can distinguish between the tip lead and the ring lead on

the baluns that lead to your controller and workstation. When you attach

your cables to the repeater, the tip lead of the balun will contact the tip lead

of the connector marked “CTRL TERM,” while the ring lead of the balun

will contact the ring lead of the same connector.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Black Box Repeater Handbücher

Black Box

Black Box IC155A Bedienungsanleitung

Black Box

Black Box 3270 Repeater-Fiber Bedienungsanleitung

Black Box

Black Box IC155A Bedienungsanleitung

Black Box

Black Box 3270 Repeater-Fiber Bedienungsanleitung

Black Box

Black Box IC155A Bedienungsanleitung

Black Box

Black Box AC3010A Bedienungsanleitung

Black Box

Black Box ICD202A Bedienungsanleitung

Black Box

Black Box IC263A Bedienungsanleitung

Black Box

Black Box CityLAN 100 Series Bedienungsanleitung

Black Box

Black Box 5250 Bedienungsanleitung

Black Box

Black Box IC496A-R2 Bedienungsanleitung

Black Box

Black Box ACX1000 Bedienungsanleitung

Black Box

Black Box LE4200A-R3 LE4202A-R3 Bedienungsanleitung

Black Box

Black Box LZ1500A-R3 Bedienungsanleitung

Black Box

Black Box Twin Mux Repeater Module - UTP Bedienungsanleitung

Black Box

Black Box VR-HDMI-50M Bedienungsanleitung

Black Box

Black Box LPR110 Bedienungsanleitung

Black Box

Black Box 4-Port BNC Repeater Bedienungsanleitung

Black Box

Black Box TL170A Bedienungsanleitung

Black Box

Black Box DKM SERIES Bedienungsanleitung

Black Box

Black Box LE4200A-R3 LE4202A-R3 Bedienungsanleitung

Black Box

Black Box WAP?300BGN Bedienungsanleitung

Black Box

Black Box WAP?300BGN Bedienungsanleitung

Black Box

Black Box LE8003A Bedienungsanleitung

Beliebte Repeater Handbücher anderer Marken

Gigaset

Gigaset 108 Bedienungsanleitung

Kenwood

Kenwood TKR-750-850 Stücklistenhandbuch

Asus

Asus RP-AC51 Bedienungsanleitung

Exibel

Exibel HRP0101 Bedienungsanleitung

Kidde

Kidde Vega Bedienungsanleitung

Telcosat

Telcosat RBB 850 Installationsanleitung

York

York Universal LINC485 Bedienungsanleitung

MIKOM

MIKOM MRx01B Power Series Bedienungsanleitung

Simrad

Simrad RD 301 Bedienungsanleitung

Tait

Tait TB7304 Bedienungsanleitung

R-tron

R-tron RSN-CDMA-37-C Bedienungsanleitung

Inventronics

Inventronics DALI REPEATER SO Bedienungsanleitung

XFP

XFP 16 Bedienungsanleitung

Andrew

Andrew MRx18 Bedienungsanleitung

COMBA

COMBA RXA3748 Bedienungsanleitung

ADRF

ADRF SDR-ICS-43 Bedienungsanleitung

Teltonika

Teltonika WRP100 Bedienungsanleitung

U-Prox

U-Prox HW Bedienungsanleitung