Black Box PSE508MA Bedienungsanleitung

Power Switch

Master/Satellite Twin

8-Port

OCTOBER 2006

PSE508MA-XX

PSE508SA-XX

SUPPORT FREE technical support

This product carries the CE mark to indicate compliance with the European Directive on

Electromagnetic Compatibility (89/336/EEC). It has been tested to EN55024:1998 and

EN55022:1998.

PSE508MA/SA

PSE508MA/SA is a couple of power control units made of a Master named Power Switch Master

Twin and a satellite named Power Switch Satellite Twin.

Power Switch Master Twin is a power control unit with a built-in Web server, an Ethernet and a

serial RS232 connection. It enables you to control the power supply of 8 power sockets either

remotely through a Network (Intranet or Internet) or locally through its serial RS232 connection.

The number of the controlled sockets can be extended up to 40 by connecting up to 4 Power Switch

Satellite Twin to the Master.

Thanks to the use of two separate power inlets and the optional Twin mode which allows you to

control at the same time two power sockets, this device is the ideal solution to control the power of

servers using redundant power supplies.

Power Switch Satellite Twin is a power control unit with a serial RS232 connection. It enables you

to control the power supply of 8 sockets through its serial RS232 connection. The number of the

controlled sockets can be extended up to 32 by cascading up to 4 Power Switch Satellite Twin.

Like the Master, this device has two separate power inlets to increase the security and the load

available on the power sockets.

Contents

Chapters

1. Safety instructions___________________________________________________________________ 2

2. Installation_________________________________________________________________________4

2.1 Connecting Power Switch Master Twin ________________________________________________ 4

2.2 Connecting Power Switch Satellite Twin _______________________________________________5

3. Configuration of the Power Switch Master Twin ____________________________________________ 6

3.1 Configuration using the Power Switch inder program ____________________________________7

3.2 Configuration using a Terminal connection _____________________________________________ 9

4. Security parameters _________________________________________________________________ 19

5. Serial port configuration ______________________________________________________________21

6. Control the power outlets _____________________________________________________________22

6.1 Control the power outlets through a Web browser _______________________________________22

6.2 Control the power outlets through a serial connection_____________________________________24

7. Technical data______________________________________________________________________27

7.1 Power Switch Master Twin _________________________________________________________27

7.2 Power Switch Satellite Twin_________________________________________________________28

POWER SWITCH PSE508MA & PSE508SA

1. Safety instructions

To be read before use!

Remark:

In the following instructions "Power Switch device" is used for both devices Power Switch Master Twin and

Power Switch Satellite Twin.

• The Power Switch devices can only be installed by qualified people with the following

installation and use instructions. The manufacturer disclaims all responsibility in case of a bad

utilization of the Power Switch devices and particularly any use with equipments that may cause

personal injury or material damage.

• This equipment is designed to be installed on a dedicated circuit that must have a circuit breaker

or fuse protection.

• The electrical power sockets used to plug the power cords of the Power Switch devices must be

close to the Power Switch devices and easily accessible.

• Check that the power cords, plugs and sockets are in good condition.

• The Power Switch devices can only be connected to three-wire 230 VAC (50-60Hz) sockets.

• Always plug the Power Switch devices into properly grounded power sockets (two poles plus

ground).

• Never exceed 10 Amp total load for each group of 4 power sockets of an Power Switch device.

• If you have to replace an external fuse of an Power Switch device, never use another type of

fuse than 10A/250V T.

• The Power Switch devices are intended for indoor use only. Do NOT install them in an area

where excessive moisture or heat is present.

• Always disconnect the 2 (two) power cords of the Power Switch device if you want to intervene

on the Power Switch device or on the equipment powered from the Power Switch device.

CHAPTER 2: Installat on

• The power outlets of the Power Switch devices are not circuit breakers! If you want to intervene

on equipment connected to an Power Switch device you must disconnect this equipment from

the Power Switch device.

• The Power Switch devices contain potentially hazardous voltages. Do NOT attempt to

disassemble them.

• The Power Switch devices contain no user serviceable parts and repairs are to be performed by

factory trained service personnel only.

POWER SWITCH PSE508MA & PSE508SA

2. Installation

The Power Switch Master Twin has a built-in Web server, an Ethernet and a serial interface. It can

be used as a stand-alone device to control over IP eight IEC power sockets. The number of

controlled sockets can be extended to 16, 24, 32 or 40 by cascading 1 to 4 Power Switch Satellite.

The Power Switch Satellite Twin has a serial RS232 interface used to control individually its 8

power sockets either through a Power Switch Master Twin or through any device using a serial

RS232 connection (PC, Console server...). By cascading up to 4 Power Switch Satellite Twin, it is

possible to control up to 32 sockets via one serial port.

2.1 Connect ng Power Sw tch Master Tw n

1. Connect your 10BasteT cable to the RJ-45 network port and to the Power Switch Master Twin.

If you want to configure the Power Switch Master Twin or control its power sockets over a

Terminal connection, connect the supplied serial cable to an available serial port on your PC and

to the serial port of the Power Switch Master Twin.

2. Plug the 2 power cables into 2 grounded sockets. The A and B LEDs light on to confirm that

power is on and the Pwr LED confirms that the Web server is powered.

3. You can now configure the Power Switch Master Twin by following the indications of the

paragraph 3 "Configuration of the Power Switch Master Twin" or, if necessary, install the

Power Switch Satellite Twin as indicated hereafter.

CHAPTER 2: Installat on

2.2 Connect ng Power Sw tch Satell te Tw n

1. Connect the supplied RJ9 link-up cable to the RJ9 Out connector of the Master and to the RJ9 In

connector of the Satellite.

To cascade several Satellites, link RJ9 Out connector to RJ9 In connector of the next satellite.

2. Allocate an address to each Satellite by positioning the address selection DIP-switches marked

Slct on the front panel according to the following table.

Remarks

- Unplug the device before changing its DIP switches.

- Do NOT use the same address for two different Satellites.

Satellite number DIP-switch 1 DIP-switch 2

1 Off Off

2 On Off

3 Off On

4 On On

Position Off = switch upwards

Position On = switch downwards

Micro-switch 1 is on the left side, micro-switch 2 on the right.

3. Plug the 2 power cables into 2 grounded sockets. The A and B LEDs light on to confirm that

power is on.

POWER SWITCH PSE508MA & PSE508SA

3. Configuration of the Power Switch Master

Twin

To use the Power Switch Master Twin on your network, you must first configure its network

parameters. Ask your network administrator for the parameters to use.

There are two different methods to configure the Power Switch Master Twin:

Method 1:

Through a network using the Power Switch Finder Program (on the delivered CD).

It is the simplest and fastest configuration method if you use Windows as operating system. We

suggest that you use this program at least during the first configuration: it allows you to configure

your Power Switch Master Twin through your local network even if its network parameters (IP

Address, Subnet mask and Port) are not compatible with those of your PC or your local network.

If you decide to use this method you can directly go to § 3.1 "Configuration using the Power Switch

Finder program".

Default Network parameters:

IP address 192.168.100.100

Subnet mask 255.255.255.0

Gateway no address

Port 80

Method 2:

Through a RS232 serial connection using a Terminal connection. If you use a PC, use the serial

cable supplied with the product and a Terminal program such as Widows HyperTerminal or the

MicroTerminal program on the CD (folder miscellaneous).

If you decide to use this method, you can directly go to § 3.2 "Configuration using a Terminal

connection".

CHAPTER 3: Conf gurat on

3.1 Conf gurat on us ng the Power Sw tch F nder program

Remarks:

The Power Switch Master Twin and the PC used to configure it have to be connected on the same segment

of the network. The protocol of this program cannot be routed so it cannot be used to configure the Power

Switch through a WAN or the Internet.

This program does not work if the administrator has deactivated it in the configuration of the Power Switch

(for security reasons for example).

1. Start the PS-Finder.exe program on the CD-ROM.

The Power Switch Finder window appears.

2. In the tool bar click on the first left button or choose the File/Scan Menu.

The program browses the segment on which is connected your PC and displays the name, the

type, the IP and MAC Address of the connected Power Switch.

3. In the tool bar click on the second left button or choose the File/Configure Menu.

The properties dialog box appears and you can now configure the network parameters. To

configure all other parameters click on the Options button on the bottom of the dialog box.

POWER SWITCH PSE508MA & PSE508SA

General Tab

This tab is used:

• to define all the network parameters of the Power Switch Master Twin (IP Address, Subnet

Mask, Default Gateway and Port Number).

• to permit or deny the configuration using the Power Switch Finder program for security reasons.

Labels Tab

This tab is used:

• to attribute a label to a group of Power Switch devices connected together (a group is made of 1

Power Switch Master Twin and up to 4 Satellites).

• to attribute a label to each Power Switch and its 8 power sockets (use the left vertical Tabs to

select the Power Switch you want to configure).

Accounts Tab

In combination with the left vertical tab Group, this tab is used:

• to attribute a name and a password to the administrator who has access to all the sockets within a

group of Power Switch.

In combination with one of the left vertical tabs «Device 1» to «Device 5», this tab is used:

• to define 8 user accounts using a name and a password for each one.

• to define the power sockets each user will be able to control.

• to activate or deactivate a Power Switch Satellite connected to the Master.

• to define the function modus of each Power Switch (Single mode or Twin mode):

- Single mode enables you to control individually each power socket,

- Twin mode enables you to control two power sockets with one command. This mode is

particularly intended to restart devices using redundant power supplies.

In that case, the 4 sockets powered by the power supply A (sockets 1 to 4) are automatically

associated to the 4 sockets powered by the power supply B (sockets 5 to 8) and the labels of the

first 4 sockets are used.

Security Tab

This tab is used to define addresses that are authorized or denied to access to the Power Switch over

the Network. For all details about these features, please refer to chapter 6 "Security parameters

configuration".

Options Tab

This tab is used to:

• define the restart delay valid for all power sockets of all Power Switch connected together;

• configure an Email address to which the user can manually send a message in case of problem.

Miscellaneous Tab

In combination with one of the left vertical tabs "Device 1" to "Device 5" to know how many times

a Power Switch has been powered ON and how many times its power sockets have been switched

from OFF to ON. These values cannot be reset by the user.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Black Box Schalten Handbücher

Black Box

Black Box KV0416A Bedienungsanleitung

Black Box

Black Box KVS4-4004DHVX Bedienungsanleitung

Black Box

Black Box SW216A Bedienungsanleitung

Black Box

Black Box KVP4004A Bedienungsanleitung

Black Box

Black Box INTEL EXPRESS 410T Technisches Datenblatt

Black Box

Black Box ServSwitch Summit KV1500A Bedienungsanleitung

Black Box

Black Box Freedom II Series Bedienungsanleitung

Black Box

Black Box SS4P-SH-DVI-UCAC-P Bedienungsanleitung

Black Box

Black Box LBH100A-PD-ST-24 Bedienungsanleitung

Black Box

Black Box KV9204A Bedienungsanleitung

Black Box

Black Box MT720A Bedienungsanleitung

Black Box

Black Box SS2P-SH-DP-U Bedienungsanleitung

Black Box

Black Box SWI080A-R3 Bedienungsanleitung

Black Box

Black Box ServSwitch Duo KV6104SA Bedienungsanleitung

Black Box

Black Box SW111A Bedienungsanleitung

Black Box

Black Box LH8000A-M Bedienungsanleitung

Black Box

Black Box ServSwitch Duo IPC KV6216FA-R2 Bedienungsanleitung

Black Box

Black Box MODULAR SMART SWITCH SW925AE Bedienungsanleitung

Black Box

Black Box AVSW-DVI4X1 Bedienungsanleitung

Black Box

Black Box LGH1000 Series Bedienungsanleitung

Black Box

Black Box LPB200A Bedienungsanleitung

Black Box

Black Box DPMSTHUB-4P Bedienungsanleitung

Black Box

Black Box KV9502A Bedienungsanleitung

Black Box

Black Box PSE544-DE-R2 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung