BLACK NOISE COSMOS Bedienungsanleitung

COSMOS

User Manual

V1.0

BLACK NOISE warrants is products to be free of

defects in materials or workmanship and to be

conform with the specications at the time of

shipment for a period of two years from the date of

purchase. During that period any malfunctioning or

damaged units will be repaired, service and calibrated

into your workshop.

This warranty does not cover any problems resulting

from damages during shipping, incorrect installation

or power supply, abusive treatment, or any other

obvious user-inicted fault. If your product warranty

is passed, it still can be serviced as long as parts

are available in our workshop. We reserve the right

to charge for labor,parts and transit expenses where

applicable.

Before sending your product to our workshop please

parcel will be rejected and or returned. The postage

to our workshop is on the customer. The return of

your module is on us. BLACK NOISE cannot take any

responsibility for damages caused during transport.

Cosmos is a new kind of module that will help you to

creating complex modulation, sounds, patterns with ease

and will lead you to new sounds territories.

Inspired by early analog computers, Cosmos is a unique,

innovative, very exible and fully analog module allowing

it to be used as: VCO, LFO, Ring Mod, Polarizer, “VCA”,

“LPG”, Phase Lock Loop, Cross-Modulation, Minimum,

Maximum, Logic Gates, Waveshaper, Complex gate

generator, Fuzz, Distorsion, Gate extractor, Trig extractor,

Gate generator, Voltage generator, Trig Generator,

comparator, window comparator, complex comparator,

Half-Rectier, Full-Rectier, Inverter, Buffered Multiples,

Mixer, Difference, Compressor, Sidechain, compressor, VC

Clipper, VC Switch, Clock doubler, Envelope follower, and

more.

With its wide elds of application Cosmos can replace

many modules but it will also bring new colors to your

palette thanks to its unique character. This makes

Cosmos the ideal module whether you have a small

case or a big system. 100% analog and with an intuitive

interface Cosmos is also very easy to use, no menu and

button combo problems.

contact@blacknoisemodular.com

Width: 14HP

Depth: 30mm

Power : +12V: 65ma

-12V: 65ma

+5V: 0ma

WarantyThank you for purchasing the Cosmos.

Contents

Starting the Cosmos .........................1

A map of the Cosmos ........................3

Looking through the Cosmos .................4

Entering the Cosmos.........................5

Exploring the Cosmos........................7

Controlling the Cosmos .....................16

Half-Wave rectier ........................17

Full-Wave rectier ..........................18

Comparator ..............................19

Window Comparator .....................20

Clamping VCA ............................21

Clamping ring modulation ..................22

Complex ring modulation ..................23

Oscillator ................................24

Triangle or saw to variable pulse width ......25

Saw wave to triangle wave ................26

Triangle wave to + 1 oct VCO ..............27

Harmonic wave shaper ....................28

Phase locked loop: VCO tracking ...........29

Phase locked loop: looping envelope .........30

Phase locked loop: external tracking ..........31

Envelope to LFO ..........................32

Envelope combiner .......................33

Envelope follower ........................34

Random Gates ..........................35

Clock multiplier with Swing ................36

Trigger multiplier with delay ............... 37

1. Turn off your eurorack system and pull of the cord.

2. Connect the provided ribbon cable’s 16 pin head

to you to the system’s power bus, making sure the

red stripe matches the one indicated on the bus

3. Connect the provided ribbon cable’s 10 pin head to

the Cosmos, making sure the red stripe matches

the one indicated on the bus.

4. Place the Cosmos on the rails of your system and

attach it with the included screws.

5. Put your system’s power cord back in and turn it

on.

6. Test the module by pushing rmly on the tactile

pads. the Related LEDs should light up according

to the pressure on the pads.

7. The Cosmos is ready. Have fun!

Installation

!! Always use the provided ribbon to power Cosmos !!

It has a specific header orientation. Other ribbon won’t

damage the module, but it will not start. Don’t use the

provided ribbon to power another shrouded module.

If the test procedure described above, comes to fail, don’t

hesitate to reach out with BLACK NOISE.

Starting the Cosmos

This step is only in case of unexpected behavior.

The module comes fully calibrated and ready to use.

As the circuit is analog, some adjustment might be

required over time. The trimmers on the top of the

back are adjusting the threshold of their respective

outputs to be converted into gates. These thresholds

should be set as close as zero. Monitor the three

gates output with an oscilloscope or a simple LED

equipped module such as GOMA and test the module

by pushing on the pads or sending gate sources to

the inputs.

1. should be LOW by default, HIGH when any pad is

pushed. Adjust the trimmer if it is not the case.

2. should be LOW by default, LOW when a single

pad is pushed, and HIGH when the two pads are

pushed. Adjust the trimmer if it is not the case

3. should be LOW by default, HIGH when a single

pad is pushed, and LOW when the two pads are

pushed. Adjust the trimmer if it is not the case.

Calibration

monitor

Starting the Cosmos

A map of the Cosmos

Cheat sheet

analog out

inverted analog out

gate out

NOT gate out

input

MIN

AND gate

AND trig

inv MIN

NAND trig

NAND gate

-X -Y

diff

MAX

OR gate

XOR gate XOR trig

TZ CLIPPER

XNOR gate XNOR trig

TZ CLIPPER inv

OR trig

inv MAX

NOR trig

NOR gate

X IN Y IN

X Ysum

Looking through the Cosmos

Two inputs with normalized touch pads

A top hemisphere that provides all kind of CV

combination, with their logic gates and rising edge

trigger counterparts

A lower hemisphere that provides a phase-inverted

version of the top hemisphere, with their NOT gates

logic and fall trigger counterparts.

The Cosmos is large, but its structure is simple:

Entering the Cosmos

The Cosmos has two inputs: X and Y. They can

process any eurorack signal. Fixed or controlled

voltage; positive, negative or bipolar signals; triggers,

gates or audio signal.

When an input is not connected, it is replaced by

the corresponding pad on the faceplate, providing

a performance oriented voltage depending on the

surface of skin in contact with the pad.

Entering the Cosmos

Exploring the Cosmos

1:1 buffered copy of the corresponding signal

Phase-inverted copy of the corresponding signal

X Y

phase inv.

Andere Handbücher für COSMOS

Inhaltsverzeichnis

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung