Blackboxav 7VS Bedienungsanleitung
1
V1
2
Safety Guide ........................................................................................... 3
Your new 7” Video Screen...................................................................... 4
Setting Up ............................................................................................... 5
Overview................................................................................................. 5
Formatting .............................................................................................. 6
Remote Control ...................................................................................... 7
Programming .......................................................................................... 8
Technical Information............................................................................. 9
Technical Drawings............................................................................... 10
3
Please observe the following when installing this device.
• This product is not designed to be
resistant to moisture or excessive
dirt/dust. When deciding on a suitable
installation point ensure there is
reasonable protection from environmental
damage.
• If there is damage to the power supply
in any way, arrange for a replacement unit
by contacting blackbox-av. They may
require you to send the defective power
unit back so in this case do not dispose of
the power supply unless prompted to do
so. If you wish to source your own power
supply a CE or FC certified double
insulated and regulated supply is
required. The Power supply has an output
rating of 12vDC at 2A, 24W. Using a
power supply with a higher voltage will
irreparably damage the display unit.
• Do not place the unit in direct sunlight
for prolonged periods as this may cause
the product to overheat.
• For disposal of old electrical equipment
please follow the guidelines associated
with your country/territory or ship the unit
back to blackbox-av and we will
dispose/recycle the unit. The symbol on
the left indicates that this product shall
not be treated as household waste.
Instead it shall be handed to applicable
collection points for the recycling of
electronic equipment. If you dispose of
this unit correctly you will be helping
prevent future harm to the environment
which is caused by poor waste
management of this type of equipment. If
the screen has been damaged take extra
care to prevent the LCD liquid from
leaking out of the unit and wrap in a
strong plastic bag with no holes.
• Whilst the unit is connected to a mains
outlet and the power is switched on it is
providing energy for operating the device.
If the unit is not being used for long
periods of time it is recommended to turn
off the power as it will prolong the life of
its electronic circuitry.
4
1. 7” Video Screen and Player
2. 12V Power Supply
3. Button Cables
4. Remote Control
5. USB or SD Card
6. Speakers
The 7” Open Frame Video Screen is an all
in one media player and screen. It’s used
to display video, images and audio in a
small compact manner. The open frame
design allows it to be easily mounted with
signage or other such installations.
It can be looping or use up to 8 activation
buttons.
The 7VS is supplied with 2 Mountable
Speakers.
5
Powered by a 12V Power Supply, the 7VS
can be turned on/off via mains.
The 7VS provides both USB and SD Card
slots for playing content (supplied as
standard with an SD Card). Go to
‘Programming’ for information on how to
program your USB or SD Card.
If you wish to use button activated content
then attach the required number of
buttons using the button wires (supplied)
to the appropriate button inputs.
The 7VS is supplied with a clear screen
protector. This ensures that the screen
doesn’t get damaged whilst in use.
The 7VS can support one 3.5mm audio
out port (upon request), supporting both
headphones and amplifiers.
The 7VS is built with 4 fixing holes for
easy mounting (two on either side).
6
Before putting the content onto either a USB or SD Card it needs to be in the right format
as listed below. Your storage medium must be formatted to FAT32.
Below are the file type requirements.
Category
Codec/FourCC
Max Res
Max Bitrate
MP4
MPEG4
800x480
10M
Sub Type
Codec
Max Res
Size
JPG
YUV400
YUV420
YUV422
YUV440
YUV444
8000x8000
No Limit
Category
Codec
Sample Rate
Bitrate
MP3
MP3
8-320Khz
32Kbps-
448kbps
For optimal image playback we
recommend images be1024 x 600 pixels
at 300DPI and saved as a JPEG.
For optimal video playback it is
recommended that your video is 1024 x
600 in .MP4 format.
For optimal audio playback it is
recommended that your audio file is
formatted to MP3 and has a bitrate of
44.1Khz.
7
The Remote Control enables you to set a range of functions.
To access the menu press the ‘setup’ button, press this again to exit.
If the 7VS is playing content you may need to press the ‘stop’ button before entering the
setup menu, otherwise a number of options might be greyed out and unable to be
accessed.
The remote sensor is located at the bottom rear of the screen.
POWER
Power On/Off
MUTE
Volume On/Off
DISP
Display current time on the top
right corner of the screen
MODE
Adjust the Play Mode
BCC
Adjust the Brightness, Colour,
Clarity and Contrast
RETURN
Return to the file list
COPY
File copy, insert USB and SD
card, double click the “COPY”
button
DEL
Delete file
VOL+
Increase Volume
SETUP
Press once to enter File list,
press twice to enter SETUP
Menu
Navigation buttons (up, left,
right, down)
VOL-
Decrease Volume
ENTER
ENTER, confirm button
Play-back / Play-forward (2x,
4x, 6x, 8x, 16x, 32x)
Previous / Next file
Pause
Stop
8
Once you have edited and converted
your content into the correct format you
will need to put these on USB or SD Card.
The file names of your content will
determine how it is activated.
The USB or SD Card will be pre-
programmed with a template, when
loading your content make sure to delete
these files. It’s recommended that you
store the template files on your computer
for future reference.
Should you need to use a different USB /
SD Card we suggest you format it to
‘FAT32’.
To program your content you will need;
1. A PC or laptop with Windows OS
2. Correctly formatted content
3. USB Stick or SD Card (Supplied)
Windows OS is required to program your
AV Point using a PC or laptop (xp –10).
MacOS is not supported due to hidden
files generated by the OS.
Place all your formatted files into the root
of the USB or SD Card whilst renaming
them like so. Each file is associated with a
button. The ‘F’ at the beginning needs to
be a capital as the player is case
sensitive.
F0000 –Looping (Content begins
automatically on startup)
F0100 –Button 1
F0200 –Button 2
F0300 –Button 3
F0400 –Button 4
…
F1000 –Button 10
Within the above configuration the player
will play: video F0000 as the loop. If
button 1 is pressed it will play F0100.
Once F0100 is complete, F0000 will
resume unless a button is pressed.
Note: The loop is designed to be used for
creating the button selection screen. This
can be an image or video but must be
named F0000.
9
0.8Kg
254 x 222 x 100 mm
197 x 109 x 27.20
Fixing Wings, 45 x 75mm VESA
Sample Rate: 8-320KHz, Bitrate: 32-
448Kbps
SDHC or USB
8
Video: .MP4, Audio: .MP3, Images: .JPG
Still Picture: up to 8000 x 8000px, Video:
1024 x 600
U45°/D50°/L45°/R50°
500:1
300-350cd/m²
2W x 2
With Speakers
10
197
109
154
87
75
181.50
R9.50
8
9.29
12.71
24
Front
27.20
Bottom
Andere Handbücher für 7VS
1
Andere Blackboxav Projektionsfläche Handbücher
Beliebte Projektionsfläche Handbücher anderer Marken
FART PRODUKT
FART PRODUKT Standard SCREEN Bedienungsanleitung
Draper
Draper E Series Handbuch
Elite Screens
Elite Screens Elite Tripod Series Bedienungsanleitung
Laarhoven
Laarhoven Companion II Bedienungsanleitung
Renogy
Renogy RMS-LFPS-US Bedienungsanleitung
Da-Lite
Da-Lite ExecutiveElectrol Bedienungsanleitung
