Blagdon MINIPOND 2000 Bedienungsanleitung
minipond
2000
www.interpet.co.uk
www.blagdonwatergardening.co.uk
water movement
pond pump
for fountains, filters
and waterfalls
water movement
minipond
2000
pond pump
for fountains, filters
and waterfalls
Congratulations on buying a Blagdon Minipond 2000
Pond pump for fountains, filters and waterfalls.
Blagdon pumps are high quality pumps manufactured
with advanced technology, to run pond fountains
filters and waterfalls.
The powerful motors are easy to maintain having a
single moving part impeller system featuring highly
wear-resistant ceramic shaft design.
IMPORTANT
Please attach proof of purchase to this manual
and file in a safe place.
1
Blagdon Minipond 2000
pond pump for Fountains,
Filters and Waterfalls
minipond
2000
2
Getting to know your Blagdon pump
Parts descriptions / spares codes - with exploded diagram
Technical specifications
Pump performance / flow chart
Installation
Electrical installation
Installing pump in pond
Maintenance and cleaning
Cleaning
Step by step guides
Routine maintenance
Monthly maintenance
Annual maintenance
Winter storage
Troubleshooting
Troubleshooting and maximise performance
Faults - problem procedure
Returning faulty pumps
Consumer advice contact details
Guarantee
3
4
5
5
6
6
7
9
9
9-10
9
10
10
10
11
11
12
12
12
13
CONTENTS
GETTING TO KNOW YOUR BLAGDON PUMP
3
GETTING TO KNOW YOUR BLAGDON PUMP
MINIPOND
2000
1
4Parts 1-3, 5-8, 10-18 and 20-22 are supplied as one package.
17 18 19
420
21
22
5
3
16
15
10
14
9 7 8
24
6
2
13
12
11
23
No. Part Description Blagdon Code
1 Pre-filter cage front
2 Pre-filter cage back 1040495
3 Pre-filter cage insert base
4 Foam pre-filter 1040501
5 Double daisy jet
6 Daisy jet
7 Bell jet 1040518
8 Foam jet
9 20 cm extension 1040525
10 Fountain T piece
11 T connector 1040532
12 Fountain flow control
No. Part Description Blagdon Code
13 T connector O ring
14 Outlet cap
15 3/4" hose tail
16 1/2" hose tail 1040532
17 1/2" outlet hose tail
18 3/4" outlet hose tail
19 1" flow control valve 1040563
20 Intake cage
21 Impeller cover 1040549
22 Impeller cover O ring
23 Impeller complete 1040556
24 Motor N/A
For spares for your Blagdon product select compatible Blagdon spare part numbers
Pump performance / flow chart
Technical Specification
& Performance
GETTING TO KNOW YOUR BLAGDON PUMP
POND PUMP MINIPOND 2000
Lift Flow rates lph
2.0 metres 240 ltr/hr (52 gal/hr)
1.5 metres 800 ltr/hr (175 gal/hr)
1.0 metres 1200 ltr/hr (264 gal/hr)
0.5 metres 1640 ltr/hr (360 gal/hr)
0.0 metres 2000 ltr/hr (440 gal/hr)
Flow is given as optimum rate
5
POND PUMP MINIPOND 2000
Cable Fitted 10 metres
Voltage 230V
Hertz 50Hz
Watts 48
Safety Rating IP68
Maximum Depth 2.2 metres
Maximum Lift 2.2 metres / 7’2”
Parts 1-3, 5-8, 10-18 and 20-22 are supplied as one package.
Electrical installation
The power supply must meet the specifications on the product.
The pump is intended to be used with either a weather-proof
cable connector or permanently connected to the fixed wiring
in the main system other than by means of a plug and socket.
The cores in the supply cable are coloured in accordance with the following
code: Brown = Live, Blue = Neutral, Green/Yellow = Earth.
The electric cable is permanently connected and sealed in the motor body.
If the supply cable is damaged the pump must not be used.
Do not use the supply cable to lift the pump as this may cause damage.
WARNING - THIS PUMP MUST BE EARTHED
A Residual Current Device (RCD), also know as the Residual
Current Circuit Breaker (RCCB), with a tripping current not
exceeding 30mA must be installed in the supply circuit.
A means of disconnection from the supply having a contact separation
of at least 3mm in all poles must be incorporated in the fixed wiring.
INSTALLATION
6
IMPORTANT: Please note all electrical work on garden lighting and
power installations must comply with part P of the building regulations.
Failure to comply is a criminal offence. If the installation of this product
is not carried out by a competent electrician who is registered under the
Part P self-certification scheme then you must notify the local building
control department before work begins. For further information and
guidance on this matter and other electrical installations in your home
that might be covered by the relevant legislation, contact your local
authorities building control department.
INSTALLATION
For permanent installations to the mains supply, it is necessary to conform to
the regulations of the local electricity authority and this would include the use
of a metal or plastic conduit to protect the cable.
Attention has been drawn to the fact that special rules may exist concerning
the installation of your pond pump (i.e. local building regulations).
These pumps must not be used in swimming pools, or areas where people are
in contact with the water.
Always disconnect the mains electricity supply whilst the equipment is being
installed, repaired, maintained or handled. Consult a qualified electrician if in
any doubt about wiring this product to the main supply.
Warning - The pond pump is provided with a thermal
cut out that temporarily switches off the pump in case of
overheating and the pump may automatically restart.
Locating your Blagdon pump
The Blagdon pump should be located on a firm and level base in the pond/
water feature in a depth of at least 10cm, but no more than 2m.
It is advisable to keep the pump off the bottom of the pond to avoid silt
entering the pump causing excessive wear and increasing pre-filter cleaning.
Fountain
Make sure there is ample cable from mains supply. Place pump in desired
location. Add Fountain extension pipes so fountain head is above surface of
the pond. Fountain height can now be adjusted, see ‘Adjusting flow control’
diagram below. See "Getting to know your Blagdon" for parts and descriptions.
If using the Daisy or Double Daisy Jet, cleaning of the jets will be reduced by
inserting the optional pre-filter foam included.
Tip: Ensure that any fountain, waterfall, filter or feature fitted does not empty
water out of pond/water feature. In windy conditions it may be necessary to shut
off or reduce the height of your fountain display to prevent water loss. Also see
the explanatory diagram on the top face of your Blagdon pump carton.
7
Never run the pump out of water as this may cause irreparable damage.
8
Tip: Ensure that any fountain or feature fitted does not empty water out of
pond/water feature. The Bell Jet and Foam Jets do not need the foam pre-filter
so require little maintenance when used with the pre-filter cage only.
Water Feature
Install as for Fountain. Depending on water feature to be supplied, your
pond pump can be used with the 1/2" hose fitting or 3/4" outlet hose fitting
which can be screwed directly into pump body. Hose clips should be used
to secure hose.
Tip: The larger 1" hose will give maximum performance when fitted.
INSTALLATION
600/900 series
600/900 series
BELL FOUNTAIN
Adjust bell by
moving head higher
for small bell and
lower for a wider
bell shape.
ADJUSTING FLOW CONTROL
Turn clockwise to increase,
anti-clockwise to
reduce flow.
Inhaltsverzeichnis
Andere Blagdon Teichpumpe Handbücher
Blagdon
Blagdon Force hybrid 5000 Bedienungsanleitung
Blagdon
Blagdon AMPHIBIOUS Series Handbuch
Blagdon
Blagdon Hydratech Torrent 3000 Bedienungsanleitung
Blagdon
Blagdon inpond 5 in 1 3000 Bedienungsanleitung
Blagdon
Blagdon Amphibious IQ Series Bedienungsanleitung
Blagdon
Blagdon Koi Air 25 Handbuch
Blagdon
Blagdon 1057233 Bedienungsanleitung
Beliebte Teichpumpe Handbücher anderer Marken
Oase
Oase PondJet Eco Bedienungsanleitung
Profi-pumpe
Profi-pumpe Rügen Bedienungsanleitung
HEISSNER
HEISSNER F540-00 Bedienungsanleitung
1A Profi Handels
1A Profi Handels OASIS 501R-1 Bedienungsanleitung
Biotop Garden
Biotop Garden D0060 Bedienungsanleitung
Profi-pumpe
Profi-pumpe JR-800LV Bedienungsanleitung
TeichTip
TeichTip Sunsun Bio Pond Filter Set Bedienungsanleitung
Hozelock Cyprio
Hozelock Cyprio Cascade 5500 Bedienungsanleitung
Hozelock Cyprio
Hozelock Cyprio Aquaforce Series Bedienungsanleitung
HEISSNER
HEISSNER SPF 150-00 Bedienungsanleitung
AquaScape
AquaScape AQUAFORCE 4000-8000 Gebrauchsanweisung
Messner
Messner system-X 1501 Bedienungsanleitung