Blaupunkt IVMS-5601 Technisches Datenblatt
In Car Video
IVMS-5601
IVMS-7001
Bedienungs- und Einbauanleitung
Operating and installation instructions
Notice d’emploi et de montage
Istruzioni d’uso e di installazione
Gebruiksaanwijzing en inbouwhandleiding
Bruks- och monteringsanvisning
Instrucciones de manejo e instalación
Instruções de serviço e de montagem
Betjenings- og monteringsvejledning
http://www.blaupunkt.com
12
DEVICE OVERVIEW
5.6" and 7"
ON
OSDSRCVIDEO
9
1
2
3
4
5
6
11
10
8
7
15.6"/ 7" TFT LCD screen for
headrests
2On/off switch
3Key for screen menu display
(OSD menu)
4Up menu
5Down menu
6AV channel setting
(AV1 - AV2 - AV3 - AV4 - AV5)
7Headphone socket
8Video input (internal)
9Connecting cable
:Interface cable
;AV signal converter unit
DANSK
13
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKAESPAÑOL
PORTUGUÊS
TABLE OF CONTENTS
Notes / Accessories .............. 14
Fitting ..................................... 14
Prepare the working area .............. 14
Mark out the dimensions ................ 15
Carefully cut open the headrest
cover ............................................. 15
Open the headrest and remove
filling and other items ..................... 15
Lay the cable through the
headrest ........................................ 16
Insert the mounting frame in
the headrest .................................. 16
Insert the monitor .......................... 16
Check and adjust the monitor then
apply the Velcro strips ................... 17
Removal ................................. 17
OSD functions ........................ 18
Main menu .................................... 18
Sub-menu ..................................... 18
Technical data ........................ 20
Guarantee .............................. 21
14
Important notes
This device is not intended for fitting in
the forward section of the passenger
compartment where it could also be
seen by the driver. Fitting this device in
any part of the vehicle where it could
interfere with or distract the driver’s at-
tention is dangerous and is not permit-
ted. The manufacturer cannot accept
responsibility for any damage caused
as a result of improper fitting of this de-
vice.
To avoid the risk of electrical
shock, the device must be protected
from water and moisture, and must
not be opened. Dangerously high
voltages are generated inside the
device.
We wish to point out that the right to
claim against warranty is invalidated by
any changes or modifications to the
device that have not been explicitly ap-
proved by the manufacturer.
Accessories supplied
Connecting cable
Extraction tool
Operating instructions
NOTES / ACCESSORIES FITTING/REMOVAL
Fitting
Note
It is recommended that the fitting is car-
ried out at a specialist workshop.
Prepare the working area
➮Remove the headrest, and place it
on a working surface that has been
cleared and cleaned, where the
further assembly procedures may
be carried out.
Note:
Take appropriate action to ensure that
the headrest is not damaged while fit-
ting the monitor.
DANSK
15
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKAESPAÑOL
PORTUGUÊS
FITTING/REMOVAL
Mark out the dimensions
➮Feel the covering of the headrest
carefully to ensure that there are
no invisible parts that would pre-
vent the monitor from being fitted.
Use the cardboard template provided
to mark out the area that will need to be
cut.
Carefully cut open the headrest
cover
Use a knife with an adjustable cutting
depth to cut out the planned area.
➮Make the first cut inside the
marked area at a point about
0.5 cm from one of the corners,
then make a diagonal cut to a point
about 0.5 cm from the opposite
corner.
➮Make a similar cut between the
other two diagonally opposed cor-
ners.
Open the headrest and remove
filling and other items
➮Carefully lift the covering material
away from the cut area.
➮Adjust the cutting depth of the knife
to about 2.5 cm, and cut into the
headrest following a line about
0.5 cm inside the marked edge.
➮Carefully lift the filling material at
one corner, and cut deeper into the
material with the knife.
➮Remove the filling material in small
pieces.
➮As you do this, lift one piece of the
filling material, and ensure that the
cut is being made to an even
depth.
To remove other pieces, use a Dremel
saw or another suitable tool.
16
FITTING/REMOVAL
➮Insert the monitor to check that it
will fit into the cut area, and make
adjustments if necessary.
Lay the cable through the
headrest
➮Now pass the supplied cables
through the opening so that they
emerge from the underneath of the
headrest.
➮If possible, cover the cable with a
cable tunnel.
➮Now connect the power supply,
ground and video signal cables, to
check that the monitor is working.
Insert the mounting frame in the
headrest
➮Before connecting the monitor,
pass the connecting cables
through the holes provided in the
mounting plate, as shown in the il-
lustration.
➮Insert the mounting plate into the
area that has been cut out, and fix
it in place with appropriate fasten-
ings.
Monitor
Mounting plate
Inserting the monitor
➮Before connecting the monitor,
pass the connecting cables
through the holes provided in the
mounting plate, as shown in the il-
lustration.
➮Insert the monitor into the mounting
plate, and attach it with appropriate
fastenings.
DANSK
17
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKAESPAÑOL
PORTUGUÊS
FITTING/REMOVAL
Check and adjust the monitor
then apply the Velcro strips
➮Connect the monitor, place it tem-
porarily in the cut-out, and place
the headrest into position.
➮Check the various monitor settings
such as brightness, headphone
function, volume control and so on.
➮Then attach the Velcro strips to the
rear of the monitor, and push the
frame onto the headrest.
Take care not to press the screen
itself, and apply pressure only in
the region of the frame.
Removal
➮To remove the screen, insert the
extraction tool between the screen
and the mounting plate.
➮Insert the extraction tool at the
place where a slot has been pro-
vided between the screen and the
mounting plate.
Extraction tool
18
FUNCTION
OSD functions
Main menu
➮Call up the main menu by pressing
the “MODE” key on the main de-
vice, or “MENU” on the remote
control unit.
➮Select the “EXIT” option to leave
the OSD menu again.
+
VOLUME
BRIGHTNESS
CONTRAST
COLOR
TINT
MISC
EXIT
●VOLUME:
Volume adjustment
●BRIGHTNESS:
Brightness adjustment
●CONTRAST:
Contrast adjustment
●COLOR:
Color adjustment
●TINT:
Screen tint adjustment
●MISC:
Opens the sub-menu
●EXIT:
Leave the OSD menu
Sub-menu
➮To reach the following menu op-
tions, select “MISC” from the main
menu.
➮When in the sub-menu, select the
“MAIN MENU” option to return to
the main menu, then select “EXIT”
to leave the OSD menu.
AUTO PROGRAM
FM CHAN: OFF
AV OUT: LINE
ZOOM: FULL
SPEAKER: OFF
REVOLVE: LEFT RIGHT
REVOLVE: UP DOWN
RESET PICTURE
MAIN MENU
Note:
Rotate UP DOWN (off function).
●AUTO PROGRAM :
See the “AUTO PROGRAM” function
in the description of the remote control
unit.
●AV OUT:
Use this option to select between the
“constant” and “variable” AV output
modes.
DANSK
19
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKAESPAÑOL
PORTUGUÊS
FUNCTION
●ZOOM :
This mode is pre-set by default to “full”.
You can make the various adjustments
for the display mode that you want by
pressing the or keys for the fol-
lowing options:
Full = display a 4:3 signal in a 16:9 im-
age format
ZOOM1 = picture height, zoom factor =
4/3
WIDTH1 = picture height and different
picture width
Normal = edge ratio 4:3
ZOOM2 = zoom factor = 8/7
WIDTH = different picture widths
WIDTH2 = picture height and different
picture width
ZOOM3 = picture height, zoom factor =
8/7
●SPEAKER:
Choose the “SPEAKER” option, then
switch the monitor loudspeaker on or
off with the or keys.
●REVOLVE
With this function and the and keys
you can revolve the display on the
screen.
●RESET:
Select the “RESET PICTURE” option to
return all the adjusted parameters to
their factory pre-set values.
●MAIN MENU:
If you are in the sub-menu, select this
option to return to the main menu.
●AUX (input):
Video input for connecting an addition-
al signal source (games console, cam-
corder, etc.)
Note:
Only use original Blaupunkt
accessory 7 607 001 510.
Or else use a mono plug.
20
Technical data
System: NTSC/PAL dual
system
Power supply / consumption:
112 V DC
±10%, <700 mA
Standby: < 1 mA
Video input level: Combined video
signal 0.7 -
2.0 Vp-p, 75 Ohm
Audio input level: 0 - 0.3 Vrms,
10 - 20 kHz
Operating temperature:
0°C - +60°C
Storage temperature:
-20°C - +70°C
Screen size (diagonal):
5.6", 7"
Contrast ratio: 150
Electrical power consumption:
< 9 W
Brightness: 400 cd/m2
Screen technology:
TFT (thin film tran-
sistor) display sys-
tem
Resolution (pixels):
5.6": 720 (H) x 234 (W) =
168,480 pixels
7": 1440 (H) x 234 (W)
= 336,960 pixels
Black light: cold cathode tube
Visible screen area:
155.52 (W) x
87.75 (H) mm
Angle of view:
5.6": from left and right:
45°,
from above: 10°,
from below: 30°
7": from left and right:
60°,
from above: 60°,
from below: 30°
Full monitor dimensions:
5.6": 140 (W) x 114 (H) x
42 (D) mm
7": 200 (W) x 127 (H) x
33,5 (D) mm
Monitor weight: < 500 g
Subject to changes!
TECHNICAL DATA
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Blaupunkt Auto-Videosystem Handbücher
Blaupunkt
Blaupunkt MICHIGAN CITY 800 W Bedienungsanleitung
Blaupunkt
Blaupunkt CHICAGO IVDM-7002 Produkthandbuch
Blaupunkt
Blaupunkt Jamaica 970 Bedienungsanleitung
Blaupunkt
Blaupunkt IVOD-1022 Bedienungsanleitung
Blaupunkt
Blaupunkt MONTEVIDEO 4020 Bedienungsanleitung
Blaupunkt
Blaupunkt IVMR 7001 Bedienungsanleitung
Blaupunkt
Blaupunkt MMP440 Bedienungsanleitung
Blaupunkt
Blaupunkt La Paz 880 Bedienungsanleitung
Blaupunkt
Blaupunkt Los Angeles 510 Bedienungsanleitung
Blaupunkt
Blaupunkt AMSTERDAM 290 BT Bedienungsanleitung
Blaupunkt
Blaupunkt DVP 01C Bedienungsanleitung
Blaupunkt
Blaupunkt COSTA MESA 900 Bedienungsanleitung
Blaupunkt
Blaupunkt SAN ANDREAS 970 Bedienungsanleitung
Blaupunkt
Blaupunkt Osaka 970 Bedienungsanleitung
Blaupunkt
Blaupunkt SANTA CRUZ 370 Bedienungsanleitung
Blaupunkt
Blaupunkt BERLIN RCM 303A Bedienungsanleitung
Blaupunkt
Blaupunkt Los Angeles 510 Bedienungsanleitung
Blaupunkt
Blaupunkt SAN MARCOS 370 Bedienungsanleitung
Blaupunkt
Blaupunkt San Andres 970 Bedienungsanleitung
Blaupunkt
Blaupunkt Osaka 760 Bedienungsanleitung
