Blaupunkt CS2010 Bedienungsanleitung

CS2010

Owner’s manual

Instrukcja obslugi

Návod k použití

Návod na použitie

Használati utasítás

Navodila

Upute za uporabu

εγχειρίδιο οδηγιών

инструкциязаупотреба

Manual de instructiuni

Instrukciju vadovas

Kasutusjuhendit

Akkus láncfűrész

Akumuliatorinis grandininis pjūklas

Ferăstrău cu lanţ cu acumulator

Akumulátorová reťazová píla

Akumulatorska verižna žaga

Akumulatora ķēdes zāģis

Cordless Chainsaw

Akumulatorowa pilarka łańcuchowa

Акумулаторен верижен трион

Akumulátorová řetězová pila

Αλυσοπρίονο μπαταρίας

Akutoitega kettsaag

Akumulatorska lančana pila

CS2010

Safety rules for machinery and electrical equipment

The device is considered suitable for use in countries with a

moderate, evenly humid climate. It can also be used in other

countries.

NOTE! Before installation or using the device, it is

absolutely necessary to read the instruction

manual and, in particular, the recommendations concerning

the safety of use. Keep the manual for inspection and pass it on

to the next users of the device.

Failure to follow these safety instructions and warnings can

result in electric shock, fire or serious personal injury.

Do not allow children and adolescents to operate the device.

Do not attempt to install, maintain or use the device if you are

not familiar with the operating instructions.

This equipment is not intended to be operated by individuals

with reduced physical, sensory or mental capabilities or lack of

experience and knowledge of the equipment, unless they have

been given supervision or instruction concerning the use of

the equipment by individuals responsible for their safety.

Explanation of warning symbols:

1. Hazard warning. Use extreme caution.

2. Important, read the instructions and observe the warnings.

3. Use safety glasses.

4. Wear safety ear muffs.

5. Always disconnect from the power source before repair or

maintenance. Unplug the device immediately if damaged.

1 2 3 4

5 6 7 8

6. Do not use the saw in rain or high humidity conditions.

7. Hold the saw securely and operate it with both hands.

8. Observe the safety rules for kickback. Avoid cutting with the

top of the chain guide bar. If so, the saw is can rotate and may

move towards the operator in an uncontrolled manner

causing a risk of injury.

Workplace safety

Ÿ Keep the work area clean and well lit. Clutter and poor

lighting contribute to accidents.

Ÿ Before starting work, prepare and clean the area, remove all

stones, branches, wires, and other foreign objects that pose

the risk of tripping.

Ÿ Take particular care when working on inclined terrain or

slopes.

Ÿ Do not use the electrically powered device in explosive

environments created by flammable liquids, gases or dusts.

The may generate sparks that can ignite dust or vapours.

Ÿ Do not use the electric saw in places with an extreme risk of

fire or explosion.

Ÿ The saw is not waterproof. Operating it in rain or humid

environments may result in electric shock.

Ÿ Children and bystanders should not be allowed in areas

where an electrically powered device is used. Distraction

may result in loss of control of the device. Leave electrically

powered garden equipment away from bystanders.

Ÿ It is the operator or the user who is responsible for accidents

or hazards to other people or the environment.

Electrical safety

Ÿ Connect the device only to an electrical supply of

characteristics in accordance with the information on the

data plate.

Ÿ Do not expose electric devices to rain or humid conditions. If

water enters the power tool, the risk of an electric shock

CS2010

increases.

Ÿ Do not tighten the connection cables. Never use the

connection cable to carry, pull electrical equipment or pull

the plug out of the socket. Keep the connection cable away

from heat sources, oils, sharp edges or moving parts.

Damaged or entangled connection cables increase the risk of

an electric shock.

Human safety

Ÿ Do not start working with a chainsaw if you feel tired or are

under the influence of alcohol, drugs or medication. Full

focus is required when using the device, be careful. A

moment of inattention while using the power tool can lead to

an accident and consequently serious injury or damage to

property.

Ÿ It is necessary to use personal protective equipment. Always

wear eye protection that is close to your face (according to

EN 166 or other national regulations). Wear hearing

protectors due to the noise generated by the device. It is also

recommended to use protective equipment such as a dust

mask, anti-slip footwear with uppers, protective gloves and a

helmet.

Ÿ Clothing should fit closely to the body. Loose clothing,

jewellery, a scarf can be caught in moving parts of the saw,

which can lead to dangerous accidents. If you have long hair

it should be secured and tightened.

Ÿ When working, the device can eject various objects, sawdust,

pieces of wood at high speed. Risk of injury. It is

recommended to use appropriate clothing.

Ÿ Remove all wrenches and other set-up tools before operating

the power tool. Leaving a wrench in the rotating part of the

power tool may result in an injury.

Ÿ Avoid working in an unnatural body position. Adopt a correct

and stable stance to avoid the risk of loss of balance. This will

allow better control of the power tool in unpredictable

CS2010

situations.

Ÿ Unintentional start-up should be avoided. Before lifting or

moving the device, make sure that the power cord is

unplugged from the power supply and the switch is in the off

position. Moving electrical equipment with your finger on

the switch or connecting it to the mains with the switch

switched on can lead to an accident.

Ÿ Keep hands and feet away from moving (rotating) parts of the

saw.

Ÿ Do not raise the working saw above your shoulders. Hold the

saw with both hands.

Ÿ Keep a safe distance from bystanders.

Despite the safe design and using protective measures

and additional safeguards, there is always a residual risk

of injury during work.

Detailed safety instructions for chainsaws.

Ÿ Do not attempt to cut metal.

Ÿ Do not use detergents or alcohol to clean the saw. Wipe with

a soft dry cloth.

Ÿ Do not use accessories not specifically intended for this

device and recommended by the manufacturer. The fact that

some accessories can be mounted to a power tool is not a

guarantee of safe use.

Ÿ The accessory mounting system must correspond to the

dimensions of the power tool. Tools of improper dimensions

cannot be sufficiently shielded or controlled.

Ÿ Use personal protective equipment. Depending on the type

of work, wear a protective mask covering the whole face, eye

protection, e.g. safety goggles. Eyes should be protected

from airborne foreign matter ejected during operation.

Protect the respiratory tract against dust and vapours with

dust masks. The effects of prolonged exposure to noise can

lead to hearing loss.

Ÿ Be careful that bystanders are kept at a safe distance from the

CS2010

working range of the chain saw. Anyone who is close to the

operating power tool must use personal protective

equipment. Chips of the material being cut or cracked work

tools can chip and cause injuries even outside the immediate

reach zone.

Ÿ Never move the power tool when it is in motion. Accidental

contact of clothing with a working tool may cut it and come

into contact with the operator's body.

Ÿ Regularly clean the device's ventilation slots. The motor

blower sucks dust into the housing and a large accumulation

of metal dust can cause an electrical hazard. Blocked

ventilation slots of

the device can also lead to overheating of the power tool.

Ÿ Before starting each time, make sure that:

- the device is assembled correctly, according to the

instructions;

- the cutting tool is in good condition; the chain attachment

must be checked regularly for damage and wear;

- safety devices (e.g. cutter guard, housing, handle, motor

switch) are in good condition and working properly.

Ÿ Only move the chainsaw away from the workpiece when the

cutting chain is running.

Ÿ Always use the support claws as a support point when

cutting through. Holding the saw by the main handle, guide

it with the auxiliary handle.

Ÿ If it is not possible to cut the material at one time, pull the saw

slightly back, move the support claw and continue cutting by

lifting the main handle of the saw slightly.

Ÿ Be extra careful when the chain gets stuck. This may result in

the kickback towards you.

Ÿ After the saw is switched off, the chain remains in motion for

some time. Caution must be maintained.

Ÿ The rotating chain of the saw heats up and expands. Without

proper lubrication and tension, it can jump off the guide bar

break off. Danger of serious accident and damage to

property.

Always turn off the saw when:

CS2010

- is left unattended;

- before adjustment and maintenance;

- after it being hit by a foreign object;

- abnormal vibrations of the device are sensed.

General information

Ÿ The device is intended for house gardening use only as

described and protected by these instructions for use. It can

be used for pruning branches, cutting firewood and other

applications requiring pruning of wood.

Ÿ Other uses can be dangerous to users and can cause damage

to the device. Do not use the device for felling trees, for

cutting materials other than wood and wood-based

materials.

Charger and battery pack safety instructions

To connect the battery pack for charging, insert the battery

pack into the charger dock and plug the charger to a power

source.

• Keep the charger away from rain and moisture. The charger

may only be used indoors.

• Keep the charger clean.

• Do not operate the charger on readily combustible objects

and surfaces (e.g. paper) or areas with flammable/explosive

atmospheres.

• Always ensure adequate ventilation when charging; fumes or

battery acid can be released from the battery pack if the latter

is compromised by poor handling or damage.

• When charging is complete, unplug the charger from the

power source. Do not leave it connected to a power source for

longer than necessary.

• Store and charge the battery pack in a dry place and make

sure it will not be flooded by water.

• Keep the battery pack terminals clean and free of dirt.

• Protect the battery pack from shocks and moisture; never

CS2010

open the battery pack or expose it to any damage.

Ÿ The battery pack charge level can be displayed with the

number of charge indicator LEDs by pressing the state of

charge indicator button on the pack; if required, charge the

battery pack for as long as required to reach the desired

charge level and the expected operating time of the cordless

power tool.

Kickback:

The kickback is sudden and uncontrollable, the device reacts to the

jamming or blockage of the cutting device. Jamming or blocking

results in a sudden jerk, in the direction opposite to the rotation of

the disc.

Kickback is the result of not reading the safety instruction.

To avoid kickback, follow the safety instructions and use methods to

prevent it

Methods to prevent kickback.

a) Hold the device by the two handles firmly and securely. Always

use the additional handle. – The operator can control the torque

and the resultant kickback forces if appropriate precautions are

taken.

b) Keep hands away from the cutting part of the device.

CAUTION: The device may injure the user if used improperly.

c) The user should stand in such a position that, in the event of a

kickback, they are not within reach of the grinder disc.

If a crossed-out waste bin symbol appears on the appliance, this indicates that the product is covered

by European Directive 2012/19/EU. Familiarise yourself with the requirements of your local electrical

and electronic waste collection system. Follow your local regulations. Do not dispose of this product

with household waste. Proper disposal of the old product will prevent potential negative effects on the

environment and human health.

Information on environmental protection

The packaging contains only the necessary elements. Every effort has been made to ensure that the

three packaging materials are easy to separate: cardboard (box), polystyrene foam (internal

protection) and polyethylene (handbags, protective sheet). The device is manufactured from

recyclable materials and can be used again after its disassembly by a specialized company. Observe

local regulations for the disposal of packaging materials, waste batteries and unnecessary equipment.

CS2010

The product is manufactured from high quality materials and components that can be recycled and

reused.

Storage

Store cordless tools in a dry place and out of the reach of

children. For safety concerns, remove the battery pack from the cordless tool before storage. When left

connected to a cordless tool, the battery pack is drained faster. Protect the battery pack and power

tools from frost, high temperatures, moisture and water.

Do not attempt to repair a failed battery pack. Only the original manufacturer or an authorised service

may repair the battery pack.

Recharge the battery packs using only the chargers specified by the manufacturer.

Storage or operation of the battery pack in unsuitable conditions may result in a battery acid leak.

Never attempt to use a damaged or modified battery pack. Damaged or modified battery packs may

cause unpredictable effects during operation, resulting in health hazards. Keep the battery pack away

from open flames and high temperature. If exposed to fire or temperatures above 130°C, the battery

pack may explode.

Installing the battery pack

Tip: Using a battery pack incompatible with the power tool may result in abnormal performance or

failure of the power tool.

Insert the battery pack into the handle until the battery pack latch clicks (the battery pack should be

flush with the receptacle edges on the power tool).

Operation

The chainsaw is used for pruning small trees and branches.

Removing and installing the chain bar

1. Turn off the chainsaw and remove the battery pack.

2. Remove the nut (3).

3. Remove the saw guard (2).

4. Release the chain tensioner bolt.

5. Remove the chain bar together with the chain.

6. Remove the worn chain from the chain bar.

7. Install a new chain onto the chain bar so that the arrow marks on the chain links on the top side of the

bar are towards the chain running direction.

8. Install the chain bar with the chain on it and engage the chain links with the drive sprocket.

9. The chain bar features a slot which must engage over the pin. If the pin is located too far out, release

the chain tensioner bolt.

10. Once the chain bar is properly installed, tighten the chain tensioner bolt (7).

11. Reinstall the chain guard and tighten the drive guard retaining nut.

CS2010

10. Power switch

11. Adjustment wrench

12. Battery pack

13. Air vent

14. Handle grip

15. Chain bar guard

16. Chain sprocket

17. Chain tensioner bolt pin

Design of the electric chain saw.

1. Switch lock button

2. Saw guard

3. Drive guard retaining nut

4. Chain guard

5. Chain bar

6. Chain

7. Chain tensioner bolt

8. Base plate

9. Hand guard

Inhaltsverzeichnis

Sprachen:

Andere Blaupunkt Kettensäge Handbücher

Blaupunkt

Blaupunkt CS3010 Bedienungsanleitung

Beliebte Kettensäge Handbücher anderer Marken

Bushranger

Bushranger CS4210 Bedienungsanleitung

Husqvarna

Husqvarna 136, 141 Bedienungsanleitung

Echo

Echo CS-330EVL Bedienungsanleitung

HART

HART HLCS01 Bedienungsanleitung

Homelite

Homelite UH10817 Bedienungsanleitung

Craftsman

Craftsman 358.350270 Bedienungsanleitung

Husqvarna

Husqvarna 336 Bedienungsanleitung

Greencut

Greencut GS6200 Bedienungsanleitung

Husqvarna

Husqvarna 42, 242XP, 246 Bedienungsanleitung

Makita

Makita EA3601FG Bedienungsanleitung

Husqvarna

Husqvarna 1151338-95 Bedienungsanleitung

Poulan Pro

Poulan Pro 380 Bedienungsanleitung

Elem Garden Technic

Elem Garden Technic TRE2042SO-OR Bedienungsanleitung

Royal

Royal RPC 3835 Bedienungsanleitung

Famastil

Famastil F-Power Bedienungsanleitung

McCulloch

McCulloch M3816 Bedienungsanleitung

Echo

Echo CS-8000 TYPE1-E Bedienungsanleitung

Echo

Echo CS-346 Bedienungsanleitung