Blichmann Engineering RIMS Rocket Montageanleitung

RIMS Rocket™

Electric Recirculation Heater

Assembly, Operation & Maintenance

Congratulations on your purchase, and thank you for selecting the RIMS Rocket™ electric recirculation

heater from Blichmann Engineering™. We are confident that it will provide you years of service and

many gallons of outstanding beer. This manual will familiarize you with the assembly, operation, and

maintenance of the RIMS Rocket™ electric recirculation heater.

IMPORTANT!!

**** PLEASE READ THOROUGHLY PRIOR TO USE FOR IMPORTANT SAFETY INFORMATION ****

Warning: Sections labeled “Warning” can lead to serious injury or death if not followed. Please read

these thoroughly and understand them completely before use. If you do not understand

them or have any questions, contact your retailer or Blichmann Engineering™

(www.BlichmannEngineering.com) before use. Do NOT at ANY time operate the product

until you thoroughly read and understand these instructions!

Caution: Sections labeled “Caution” can lead to equipment damage or unsatisfactory performance of

the equipment. Please read these sections thoroughly. If you have any questions, contact

your retailer or Blichmann Engineering™ (www.BlichmannEngineering.com) before use.

Important: Sections labeled “Important” are critical to the proper performance and life of the product.

RIMS Rocket™ Owner’s Manual – V1

©Blichmann Engineering, LLC 2014

Assembly:

The RIMS Rocket™ electric recirculation heater is packaged unassembled to allow for more economical

shipping and to reduce damage in shipment. A list of components included with your RIMS Rocket™

electric recirculation heater follows as well as the basic tools required for assembly. Please carefully

review the lists below to ensure you received all of the correct parts and have the required tools prior

to assembly.

Parts List:

Item Quantity Item Quantity

Heater Coil 1 Heater Cable

Assembly

Bulkhead Nut

5/8-18 Jam Nut

2 S70-208 O-ring

Plug Guard 1 Lid

1-2*

Pressure Relief Plug 1

Required Tools:

7/8” Deep Well Socket and Ratchet

1” Open End or Adjustable Wrench

*Always follow tool manufacturer instructions and safety precautions

RIMS Rocket™ Owner’s Manual – V1

©Blichmann Engineering, LLC 2014

Step One:

First remove both bulkhead nuts from the heater

coil. Next install the heater coil through the lid and

plug guard as shown in Figure 1. Make certain the lid

is oriented as show or the RIMS Rocket™ electric

recirculation heater will not seal. Last, re-install the

bulkhead nuts finger tight.

Warning: NEVER install the RIMS Rocket™ electric

recirculation heater without the plug guard. Doing

so can result in personal property damage, injury,

electrocution and death.

Figure1

Figure 2

Step Two:

Using a 1” open end or adjustable wrench, hold the

bulkhead fitting while tightening the bulkhead

retaining nut with a 7/8” deep well socket and

ratchet as shown in Figure 2. Tighten both

bulkhead retaining nuts before proceeding.

Step Three:

Place the large black O-ring provided with

your HopRocket™ over the heater coil and

locate it in the recessed portion of the lid.

Next, remove all internal components from

the HopRocket™ canister and install the

canister over the heater coil and situate it on

the lid and large black O-ring seal as shown in

Figure 3. Lastly, install the band clamp and T-

handle nut as per the instructions provided in

the HopRocket™ Owner’s Manual.

Caution: ALWAYS apply a lubricant such as

petroleum jelly, food grade silicone grease, or

mineral oil to the draw bolt and T-handle nut

to prevent the threads from seizing. Thread

galling is not covered under warranty.

Figure 3

Large Black O-ring

Bulkhead

Nut

Plug

Protector

Lid

Terminal

Pin Bulkhead

Fitting

RIMS Rocket™ Owner’s Manual – V1

©Blichmann Engineering, LLC 2014

Operation:

Warning

: The RIMS Rocket™ electric recirculation heater is only to be used in conjunction with a

Ground Fault Circuit Interrupter (GFCI) protected power source. If you are uncertain about the status

of your power source contact a licensed and qualified electrician familiar with National Electric Code

standards before proceeding. Operating the RIMS Rocket™ electric recirculation heater in any fashion

other than described in this manual can result in personal property damage, injury, electrocution or

death.

Getting Started

The RIMS Rocket™ electric recirculation heater requires the use of a temperature control device

capable of regulating power and de-energizing the heater coil to safely operate. The RIMS Rocket™

electric recirculation heater was designed specifically for use with the Blichmann Engineering™ Tower

of Power electric temperature control module. Although the RIMS Rocket™ may be compatible with

other commercially available brewing controllers, the Tower of Power™ electric temperature control

module provides the ultimate in safety, convenience, accuracy, and precision.

To operate the RIMS Rocket™ electric recirculation heater, you must verify your system can maintain a

minimum flow rate of ¾ of a gallon per minute. If you are unable to achieve the minimum flow rate,

the power of the heater coil must be reduced. The RIMS Rocket™ electric recirculation heater is

specifically designed for use with the Tower of Power™ electric temperature control module which

provides the perfect means of controlling temperature and power.

Installation

The RIMS Rocket™ electric recirculation heater

requires a constant flow of wort, provided by a

pump, to increase and maintain the

temperature of your mash. To function properly,

it is critical that the RIMS Rocket™ is located

after the outlet of the pump and no higher

than the bottom of the mash tun. A pictorial

diagram with bold arrows indicating the

direction of flow is shown in Figure Op-1.

Figure Op-1

Pump Inlet

Pump Outlet

Temp

Sensor

Mash Tun

Temp.

Control

Module

Heater

Cable

RIMS Rocket™ Owner’s Manual – V1

©Blichmann Engineering, LLC 2014

Pressure Relief Plug

Warning: When using the RIMS Rocket™ electric recirculation heater, always have the outlet of the

HopRocket™ canister unrestricted. NEVER install valves, fittings or any other devices downstream from

the outlet of the HopRocket™ canister which can impede or block the flow of liquid or evacuation of

pressure from the HopRocket™ canister.

Your RIMS Rocket™ electric recirculation heater comes from the factory with a pressure relief device

installed to prevent unsafe over pressurization of the canister. When installing the RIMS Rocket™

electric recirculation heater, always make sure the pressure relief device is installed as shown in the

sectioned diagram in Figure Op-2. Also, make certain that the bottom of the HopRocket™ canister is

oriented in a safe direction in the event of over pressurization. Do not stand or allow children or pets

in the area directly below the RIMS Rocket™ electric recirculation heater and HopRocket™ canister.

ALWAYS orient the pressure relief

device as shown in Figure Op-2. Make

sure the flange of the silicone pressure

relief plug is located on the same side

of the lid as the plug protector.

Warning: NEVER replace the pressure

relief device with anything other than

genuine Blichmann Engineering™

replacement parts. The use of non-OEM

parts can result in dangerous

conditions that can result in personal

property damage, injury or death.

Figure Op-2

Warning: NEVER energize the heater without the heating coils fully submerged. “Dry firing” the RIMS

Rocket™ electric recirculation heater will cause the heater coil to reach excessive temperatures which

can create a dangerous situation which can result in personal property damage, injury or death.

Silicone

Pressure

Relief Plug

Flange

Plug Guard

RIMS Rocket™ Owner’s Manual – V1

©Blichmann Engineering, LLC 2014

Connecting the Heater

First verify the power control device is

turned off and disconnected from any

power source. Next connect the custom

molded plug to the terminal pins of the

RIMS Rocket™ as shown in Figure Op-3. After

the custom molded plug is connected to the

heater, connect the male twist lock

connector to the power control device. At

this point is safe to connect the power

control device to a GFCI protected power

source.

Tip: The heater cord can be installed in the

alternate position by removing the screw

plug and relocating the cable strain relief

fitting to the alternate positon to relieve the

cable and provide more convenient cable

routing.

Warning: NEVER operate the RIMS Rocket™

electric recirculation heater without the

plug protector installed!

Warning: NEVER plug the RIMS Rocket™

electric recirculation heater directly into a

power source. ALWAYS use a power control

device capable of de-energizing the heater

coil.

Figure Op-3

Warning: NEVER plug in or unplug the heater cord from the heater coil when energized. Doing so will

result in arc damage to electrical connections.

Caution: Before making any connections to the RIMS Rocket™ electric recirculation heater, make

certain that the RIMS Rocket is completely filled with water or wort and your system is able to maintain

a minimum flow rate of ¾ of a gallon per minute. If your system cannot achieve the minimum flow

rate, the average power output of the RIMS Rocket™ electric recirculation heater must be reduced.

RIMS Rocket™ Owner’s Manual – V1

©Blichmann Engineering, LLC 2014

Temperature Sensor

The location of the temperature sensor for the temperature control module must be located as near to

the outlet of the RIMS Rocket™ as possible. Reducing the distance between the heat source and the

temperature sensor minimizes over shooting the set point of the temperature control device.

Although the heater may cycle on and off frequently, the stability of the system is optimized. The

recommended temperature sensor location method is shown in Figure Op-4.

Figure Op-4

Heating

Before energizing the RIMS Rocket™ electric recirculation heater, you must verify your system can

maintain a minimum flow rate of ¾ of a gallon per minute. If you are unable to achieve the minimum

flow rate, the power of the heater coil must be reduced. The RIMS Rocket™ electric recirculation heater

is specifically designed for use with the Tower of Power™ electric temperature control module which

provides the perfect means of controlling temperature and power.

Important: The ability to maintain required flow rates and modulate is necessary to prevent

scorching.

Warning: The outlet of the RIMS Rocket™ electric recirculation heater must always be unobstructed

and open to atmospheric pressure. NEVER close both the inlet and outlet of the RIMS Rocket™ electric

recirculation heater. Doing so can result in extremely dangerous pressures that can cause personal

property damage, injury or death.

Warning: When operating the RIMS Rocket™ electric recirculation heater, the surface of the heater

and surrounding areas will be hot and can cause burns. Always keep children and pets away from hot

surfaces and wear appropriate personal protective equipment such as gloves, clothing and footwear

to prevent burns and scalds

Temperature

Sensor

O-ring O-ring

Retainer

Optional

Temp Sensor

Fitting

(BE-000268-00)

Flow Direction

Hop Rocket

Canister

Outlet

RIMS Rocket™ Owner’s Manual – V1

©Blichmann Engineering, LLC 2014

NEVER:

NEVER leave this equipment unattended

NEVER allow children near this equipment

NEVER heat cooking oil with this equipment

NEVER operate on soft, uneven surfaces like dirt, gravel, or asphalt

NEVER use near or with combustible chemicals, gasoline or other flammable vapors or liquids

NEVER bypass the GFCI circuit protection

NEVER operate any equipment with frayed or damaged power cables

NEVER expose electrical connections to moisture

NEVER connect heater cable assembly directly to power source

NEVER modify or alter the supplied electrical cables or connectors

NEVER operate heater with higher than rated voltage

NEVER unplug heater when energized

NEVER energize the heater without the heating coils fully submerged.

NEVER immerse the terminal pins in water or cleaning solutions

ALWAYS:

ALWAYS use heater with rated voltage

ALWAYS unplug heater when de-energized

ALWAYS use on level and stable hard surfaces

ALWAYS connect to a GFCI circuit

ALWAYS check power cables and connectors for signs of damage or wear prior to each use

ALWAYS check that all fasteners are properly tightened prior to each use

ALWAYS use approved control device between heater and GFCI power source

ALWAYS use genuine Blichmann Engineering replacement parts

ALWAYS unplug before moving

ALWAYS allow the brewing equipment to fully cool before handling

ALWAYS wear appropriate personal protective equipment, such as gloves, clothing and

footwear to prevent burns and scalds

RIMS Rocket™ Owner’s Manual – V1

Maintenance:

Cleaning

The RIMS Rocket™ electric recirculation heater will require cleaning after use. First confirm the custom

molded plug is disconnected from the RIMS Rocket™ electric recirculation heater and is disconnected

from any power source. Use hot water and Five Star Chemical’s Powdered Brewery Wash or similar

detergent with a scrub brush or ScotchBrite™ scouring pad to remove any heavy soil deposits.

Periodically remove the RIMS Rocket™ electric recirculation heater from the lid to remove build-up of

mineral deposits. If you brew with particularly hard water, you may need to use a weak acid, such as

distilled white vinegar, to assist with removing mineral deposits. The terminal pins of the RIMS

Rocket™ electric immersion heater can tolerate incidental contact with water in the course of cleaning,

however, never immerse or soak the terminal pins of the RIMS Rocket™ in water or cleaning solutions.

Before and after each use, inspect the RIMS Rocket™ electric recirculation heater, custom molded plug,

cable, and connectors for wear or damage. If any of the above parts show signs of wear or damage,

discontinue use and contact your Blichmann Engineering™ authorized retailer for replacement parts.

Warning: ALWAYS make sure the RIMS Rocket™ electric recirculation heater is disconnected from all

power sources before cleaning.

Warning: NEVER immerse or soak the terminal pins of the RIMS Rocket™ in water or cleaning

solutions. Doing so can cause permanent damage to the heater and create an unsafe condition which

can result in personal property damage, injury, electrocution or death. ALWAYS allow the RIMS

Rocket™ electric recirculation heater to thoroughly dry after cleaning and before reinstalling.

Caution: Never use chlorine bleach or H-Cl acid to clean your RIMS Rocket™ electric recirculation

heater. Pitting in the surface of the heater coil and/or bulkhead fittings caused by the use of products

containing chlorine or H-Cl acid is not covered under the warranty.

RIMS Rocket™ Owner’s Manual – V1

Expolded Parts Diagram:

Inhaltsverzeichnis

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung