Blizzard Lighting PROKONTROL MH Bedienungsanleitung

PROKONTROL

Blizzard Lighting, LLC

www.blizzardlighting.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

1. GETTING STARTED 3

1.1 What’s In The Box? 3

1.2 Getting It Out Of The Box 3

1.3 Powering Up! 3

1.4 Getting A Hold Of Us 3

1.5 Instructions on Our Instructions 4

2. INTRODUCTION 5

2.1 Features 5

2.2 General Overview 5

2.3 The ProKontol™ MX Pin-up Pictures 5

2.4 Button and Fader Functions 5

2.5 Common Terms 7

3. OPERATING INSTRUCTIONS 8

3.1 Setup 8

3.1.1 Setting Up The System 8

3.2 LCD Menu Navigation 8

3.4 Fixture Adressing / Patching Fixtures and Faders 9

3.4 Fixture Patching Instructions (Step by Step) 10

3.5 System Functions 11

3.5.1 Resetting the Systems 11

3.5.2 Delete All Fixture Patches 11

3.5.3 Data Back-Up 11

3.5.4 Load Data 11

3.5.5 Send Fixture Update File 11

3.5.6 RDM DMX Address Setup 12

3.6 Manual Fixture Control 12

3.7 Fade Mode 12

3.8 Built-In Movement and Color Effects 12

3.9 Scenes and Chases 13

3.9.1 Scene Editing 13

3.9.2 Chase Editing 13

3.9.3 Run Scenes 13

3.9.4 Run Chases 13

3.9.5 Fade In/Out Time of Color Channels 14

3.9.6 Firmware Updates 14

4. APPENDIX 15

4.1 A Quick Lesson On DMX 15

4.2 Keeping Your ProKontrol™ MH As Good As New 16

4.3 Returns (Gasp!) 16

4.4 Shipping Issues 16

4.5 Tech SPECS! 17

Page 3

1. GETTING STARTED

What’s In The Box?

 •1xPROKONTROL™MHDMXController

 •1x9VDC,800maAC/DCAdaptor

 •AWarrantyCard&WarrantyInfo

 •ThisLovelyUserManual

1.2 Getting It Out Of The Box

We could tell just by lookin’ atcha. You’re a bit of a control freak, aren’t ya? Just kidding!

CONGRATULATIONS! You’ve purchased a GREAT little DMX controller! Bravo! Now that

you’ve got your PROKONTROL™ MH, you should carefully unpack the box and check the

contents to ensure that all parts are present and in good condition. If anything looks as if it

has been damaged in transit, notify the shipper immediately and keep the packing material

forinspection.Again,pleasesavethecartonandallpackingmaterials.Ifaxturemustbe

returnedtothefactory,itisimportantthatthexturebereturnedintheoriginalfactory

box and packing.

1.3 Powering Up!

Allxturesmustbepowereddirectlyoffaswitchedcircuitandcannot be run off a

rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

channel is used solely for a 0% to 100% switch.

AC Voltage Switch -Notallxtureshaveavoltageselectswitch,sopleaseverifythatthe

xtureyoureceiveissuitableforyourlocalpowersupply.Seethelabelonthextureor

refertothexture’sspecicationschartformoreinformation.Axture’slistedcurrent

ratingisitsaveragecurrentdrawundernormalconditions.Checkthextureordevice

carefully to make sure that if a voltage selection switch exists that it is set to the correct

line voltage you will use.

Warning! Verify that the voltage select switch on your unit matches the line

voltage applied. Damage to your xture may result if the line voltage applied does

not match the voltage indicated on the voltage selector switch. All xtures must

be connected to circuits with a suitable Ground (Earthing).

1.4 Getting A Hold Of Us

If something is wrong, just give us a call or send an email. We’ll be happy to help, honest.

Blizzard Lighting

N16 W23390 Stoneridge Dr. Suite E

Waukesha, WI 53188 USA

www.blizzardlighting.com

414-395-8365

Email: [email protected]

Disclaimer:Theinformationandspecicationscontainedinthisdocumentaresubject

to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any

errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the

right to update the existing document or to create a new document to correct any errors

or omissions at any time. You can download the latest version of this document from www.

blizzardlighting.com.

Author: Date: Last Edited: Date:

J. Thomas 8/5/2013 J. Thomas 8/7/2013

Page 4

IMPORTANT SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to

someone else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage,

and that the line voltage you are connecting to is not higher than

thatstatedonthedecalorrearpanelofthexture.

• This product is intended for indoor use only.

• Topreventriskofreorshock,donotexposexturetorainormois-

ture.

• Makesuretherearenoammablematerialsclosetotheunitwhile

operating.

• ALWAYS disconnect from the power source before servicing or re-

placing fuse and be sure to replace with same fuse size and type.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit im-

mediately.NEVERtrytorepairtheunitbyyourself.Repairscarried

out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always

use the same type spare parts.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the

housing or attempt any repairs yourself. In the unlikely event your unit may re-

quire service, please contact Blizzard Lighting at [email protected].

1.5 Instructions on Our Instructions

We try to make these manuals easy to read and as fun as reading an instruc-

tion manual can be. Because there are buttons, switches, sliders and knobs

galore on most of our products, it makes sense to refer to things in a consistent

fashion. So, when you see text formatted in certain ways, it should say to you

“Hey! Look at me! I MEAN something, dammit!”

Special Text What It Means

LCD Textdisplayedonthexture’sLCDcontrolpanel

<MENU> Button <X> to be pressed

Page 5

2. INTRODUCTION

2.1 Features

• DMX512 standard with RDM protocol compatibilty.

• 512 DMX channels

• Controlsupto32xtures,eachwithuptoof18DMXchannels

• Fixture starting addresses and channels can be soft patched

• 32 chases, able to run 5 chases simultaneously

• 32 scenes, all scenes are able to be operated simultaneously

• 9built-ineffectbuttonsformovingheadxtures,plus 7 built-in

color effect buttons

• USBportforrmwareupdatesanddatabackup

• Sound control via built-in microphone

2.2 General Overview

The ProKontrol™ MH is a universal intelligent lighting controller with RDM

protocol compatibilty. Once properly patched it it’s the perfect controller for

anymovingheadxture,allowingeaseofusewithitsdedicatedPANandTILT

wheels.Itallowsthecontrolof32xturescomposedof18channelseach.

Programs can be triggered by music, midi,automatically or manually. You can

run up to 5 chases, and all scenes can be executed at the same time.

Onthesurfaceyouwillalsondavarietyofprogrammingtoolssuchas16

universal c-hannel sliders, quick access “Movement” and built-in “Color Effect”

buttons, plus an LCD display indicator for easy navigation of all controls and

menu functions.

2.3 The ProKontrol™ Pin-up Pictures

proKONTROL MH

™

Page 6

Number Button/Fader/Connection Does...

1NUMBER Buttons

Functions differently in different

modes.

2FIXTURE Button

When activated, the 16 number but-

tonsxtureselection.

3MOVEMENTButton

When activated, the 16 number but-

tons built-in movements/macros.

4SCENE Button

When activated, the 16 number but-

tons scene playback

5CHASE Button

When activated, the 16 number but-

tons are for chase playback.

6PAN/TILT Wheels

Functions differently in different

modes.

7USB Port

Usedforrmwareupdatesanddata

backup. FAT32 and FAT16 supported.

8REC/ENTER Button REC/ENTER

9MENUS/ESC Button MENUS/ESC

10 BLACKOUT/DEL Button BLACKOUT/DELETE

11 RUN MODE/SWAP Button RUN MODE/SWAP

12 LCD Screen LCD Screen

13 Faders Adjusts the DMX output value

14 DMX Out DMX Out (3-pin)

15 DC Input DC Input

16 Power On/Off Power On/Off

Number Buttons

• In CHASE mode, press a number button, the chase will be activated or

deactivated.

• In SCENE mode, press a number button, the scene will be activated or

deactivated.

• InMOVEMENTmode,pressanumberbutton,themovementwillbe

activated or deactivated.

• InFIXTUREmode,pressanumberbutton,axturewillbeselectedor

deselected.

Faders

• In FIXTURE mode, move a fader to adjust the DMX output value.

Pan/Tilt Wheels

• In CHASE mode, PAN/TILT wheels are to adjust the chase speed and time

respectively.

• InSCENEmode,nothingdenedinPAN/TILTwheels.

• InMOVEMENTmode,PAN/TILTwheelsaretoadjusttheMOVEMENT

parameters.

• In FIXTURE mode, PAN/TILT wheels are to adjust the output values of PAN/

TILT.

2.4 Button and Fader Functions

Page 7

2.5 Common Terms

The following are common terms used in intelligent light programming, so pay

attention! We’ll be using many of them throughout the manual.

• Blackoutisastatebywherealllightingxtureslightoutputareset

to 0 or off, usually on a temporary basis.

• DMX-512 stands for Digital MultipleXis an industry standard digital

communication protocol used in entertainment lighting equipment.

For more information read the DMX Primer and DMX Control Mode

Sections later in the manual.

• Fixture refers to your lighting instrument or other device such as a

fogger or dimmer of which you can control.

• Programs are a bunch of scenes stacked one after another. It can be

programmed as either a single scene or multiple scenes in sequence.

• Scenes are static lighting states.

• Sliders are a delicious small burger or sandwich, but here they are

used in the same context as faders.

• Chases can also be called programs. A chase consists of a number of

scenes stacked one after another.

• Scanner refers to a lighting instrument with a pan and tilt mirror;

however, in the ProKontrol™ MH controller it can be used to control

anyDMX-512compatibledeviceasagenericxture.

• MIDI stands for Musical Instrument Digital Interface, and is a

standard for representing musical information in a digital format. A

MIDI input would provide external triggering of scenes using midi

device such as a midi keyboard.

• Stand Alonereferstoaxture’sabilitytofunctionindependentlyof

an external controller and usually in sync to music, due to a built in

microphone.

• Fade Slider is used to adjust the time between scenes within a

chase.

• Speed Slider affects the amount of time a scene will hold its state. It

is also considered a wait time.

• Shutterisamechanicaldeviceinthelightingxturethatallowsyou

to block the lights path. It is often used to lessen the intensity of the

light output and to strobe.

• PatchingreferstotheprocessofassigningxturesaDMXchannel.

• Playbacks can be either scenes or chases that are directly called to

execution by the user. A playback can also be considered program

memory that can be recalled during a show.

Page 8

3. OPERATING INSTRUCTIONS

3.1 Setup

3.1.1 Setting Up The System

Plug the AC to DC power supply to the system back panel and to the mains

outlet.

PluginyourDMXcable(s)toyourintelligentlightingasdescribedinthextures

respective manual. For a quick lesson on DMX see the DMX Primer section in

the Appendix of this manual.

3.2 LCD Menu Navigation

Press and hold the <MENUS> button for 2 seconds to enter/exit Menu Mode.

The menu options are as follows:

01. Patch Fixture-Topatchxturesstartingaddressesandthe

channel position, etc.

02. Reset Factory - To restore the factory settings.

03. Delete All Fixture Patch - To delete all patch settings.

04. Fade Mode - To set fade time mode.

05. RDM DMX Address Setup - To implement RDM functions.

06. Data Back Up - To back up data to a USB memory stick.

07. Data Load - To load data from a USB memory stick.

08. Send Fixture Update File-Tosendthextureupdatecode.

The PAN wheel is used to browse between the menu options.

Page 9

3.3 Fixture Adressing / Patching Fixtures and Faders

Thiscontrollerisprogrammedtocontrol18channelsofDMXperxtureonits16

faders plus the PAN and TILT encoder wheels.

To take full advantage of your ProKontrol™ MH, you’ll need to patch in the DMX

addresscodesofthexturesandfaders.Theaddressofthexturesandfaderscan

bechangedasneeded,butrstlet’sjustlookatthedefault values.

The default Fixture Patch Settings are:

Page Fixture DMX Start Address Page Fixture DMX Start Address

1 001

17 289

2 019 18 307

3 037 19 325

4 055 20 343

5 073 21 361

6 091 22 379

7 109 23 397

8 127 24 415

9 145 25 433

10 163 26 451

11 181 27 469

12 199 28 487

13 217 29 505

14 235 30 (Blank)

15 253 31 (Blank)

16 271 32 (Blank)

Fader DMX Ch. Fader DMX Ch. Fader DMX Ch.

1/R (Red) 1 7 7 13 13

2/G (Green) 2 8 8 14 14

3/B (Blue) 3 9 9 15 15

4/W (White) 4 10 10 16 16

5/D (Dimmer) 5 11 11 PAN 17

6 6 12 12 TILT 18

And the default Fader Patch Setting are:

In the above table, R=RED, G=GREEN, B=BLUE, W=WHITE, D=DIMMER

DMX START ADDRESS + FADER CHANNEL, - 1 = FADER DMX ADDRESS

Forexample:Withthesedefaultxturepatchsettings,theFIXTURE1PANDMX

addressis17,soxiture2PANDMXaddresswouldbe35.

BeforecontrollingaxturewithoutRDMfunction,youneedtopatchthexture’s

DMX starting address. For example, if you are patching a moving head, you

must patch the pan/tilt channels of the moving head to PAN/TILT wheels on the

ProKontrolMH.IfyouarepatchinganLEDxture,then,youmustpatchtheRed,

Green, Blue, White and Dimmer channels to the corresponding faders respectively.

The ProKontrol MH will then be able to correctly run all of its built-in movements

and fade in/out effects with the patch setting.

Page 10

3.4. Fixture Patching Instructions (Step by step)

Followthesestepstobeginpatchingyourxtures:

1. Press and hold <MENUS> for 2 seconds to enter Menu Mode.

2. Rotate the PAN wheel to locate: 01. PATCH FIXTURE.

3. Press <ENTER>toconrm.

4. Selectaxture(onlyonexturecanbeselected).

5. Press <SWAP> to switch between the four settings: DMX START

ADDRESS, FADER CHANL, FADER REVERSE and COLOR FADE.

6. In DMX START ADDRESS,rotate the PAN wheel to adjust the DMX

start address; press <ENTER> to save, or press <DEL> to delete

the existing DMX start address.

7. In FADER CHANL, rotate the PAN wheel to select a fader name

within “1/R” to “TILT”. Rotate the TILT wheel to adjust the address

of the corresponding DMX channel within 1-40. Press <ENTER> to

save the patching or press <DEL> to delete the existing patching.

8. In FADER REVERSE, rotate the PAN wheel to select a fader name

within “1/R” to “TILT”. Rotate the TILT wheel to select YES or NO;

YES means to set the corresponding channel reverse; NO means

inverse. Press <ENTER> to save the setting.

9. In COLOR FADE,you can enable or disable the fade in/out time of

thexture’scolorchannels.RotatethePANwheel,selectYESor

NO; YES means to enable; NO means to disable. Press <ENTER>

to save the settings.

10. Tocopyapatchedxturetoanewxture,press and hold the

numberbuttonofthepatchedxture,thenpressthenumber

buttonofanewxture.

11. Press <ESC> to exit patch setting.

*DMX START ADDRESS + FADER CHANNEL, - 1 = FADER DMX ADDRESS

Example: If FIXTURE 1 is set to 11 as its DMX starting address, and its 1/R

fader channel is set to 1, when you move the 1st fader the output of the 11th

DMX channel will be changed.

But, if FIXTURE 1 is set to 11 as its DMX starting address, and its 1/R fader

channel is set to 10, and you move the 1st fader, the output of the 20th DMX

channel will be changed.

When patching, a “!” mark will be shown in the LCD display when there is

a overlap in the patching of DMX channels. This will need to be corrected,

otherwise the DMX output may run in error.

Inhaltsverzeichnis

Andere Blizzard Lighting Controller Handbücher

Blizzard Lighting

Blizzard Lighting SoC-It Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung