Blizzard Lighting LOOP Bedienungsanleitung

Blizzard Lighting, LLC

www.blizzardlighting.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

LOOP™ LED Moving Head 1

1. Getting Started 3

What’s In The Box? 3

Getting It Out Of The Box 3

Powering Up! 3

Getting A Hold Of Us 3

Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet LOOP™ 5

Main Features 5

DMX Quick Reference 5

The LOOP™ Pin-up Picture 6

3. Setup 7

Fuse Replacement 7

Connecting A Bunch Of LOOP™ Fixtures 7

Data/DMX Cables 7

Cable Connectors 8

3-Pin??? 5-Pin??? Huh? 8

Take It To The Next Level: Setting up DMX Control 8

Installation 9

4. Operating Adjustments 10

The Control Panel 10

Control Panel Menu Structure 11

DMX / Art-Net Modes 12

Set the Starting DMX Address 12

Select the DMX Channel Mode 12

DMX512 and Art-Net Mode 12

Network Setup 12

Slave Mode 12

Auto Mode 12

Sound Active Mode 13

Display Timeout 13

Display Invert 13

Pan/Tilt Invert 13

Calibration Settings 13

Encode (Pan/Tilt Error Correction) 13

Fixture Test 13

Motor/Factory Reset 13

Runtime Info 13

DMX Values In-Depth 14

 LEDIdentication      17

5. Appendix 18

A Quick DMX Lesson 18

Keeping Your LOOP™ As Good As New 19

Returns (Gasp!) 19

Shipping Issues 19

Tech Specs 20

Dimensions 21

Page 3

1. GETTING STARTED

What’s In The Box?

• 1 x LOOP™ LED Moving Head Fixture

• 1 x Ever-So-Handy Power Cord

• 1 x Set of Mounting Brackets

• This Lovely User Manual

Getting It Out Of The Box

Congratulations on your purchase of LOOP™, the LED moving head packed with tons

of beamy, loopy goodness! Now that you’ve got your LOOP™ (or hopefully LOOPs)

, you

should carefully unpack the box and check the contents to ensure that all parts are pres-

ent and in good condition. If anything looks as if it has been damaged in transit, notify the

shipper immediately and keep the packing material for inspection. Again, please save the

cartonandallpackingmaterials.Ifaxturemustbereturnedtothefactory,itisimpor-

tantthatthexturebereturnedintheoriginalfactoryboxandpacking.

Powering Up!

Allxturesmustbepowereddirectlyoaswitchedcircuitandcannot be run o a

rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

channel is used solely for a 0% to 100% switch.

AC Voltage Switch -Notallxtureshaveavoltageselectswitch,sopleaseverifythatthe

xtureyoureceiveissuitableforyourlocalpowersupply.Seethelabelonthextureor

refertothexture’sspecicationschartformoreinformation.Axture’slistedcurrent

ratingisitsaveragecurrentdrawundernormalconditions.Checkthextureordevice

carefully to make sure that if a voltage selection switch exists that it is set to the correct

line voltage you will use.

Warning! Verify that the voltage select switch on your unit matches the line

voltage applied. Damage to your xture may result if the line voltage applied does

not match the voltage indicated on the voltage selector switch. All xtures must

be connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, please just visit our website at www.blizzardlighting.com/

support and open a support ticket. We’ll be happy to help, honest.

Disclaimer:Theinformationandspecicationscontainedinthisdocumentaresubject

to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any

errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the

right to update the existing document or to create a new document to correct any errors

or omissions at any time. You can download the latest version of this document from www.

blizzardlighting.com.

Author: Date: Last Edited: Date:

J. Thomas 6/16/2017 J. Thomas 6/16/2017

Page 4

Please read these instructions carefully. They include

important information about the installation, usage and

maintenance of this product.

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone

else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that

the line voltage you are connecting to is not higher than that stated on the de-

calorrearpanelofthexture.

• This product is intended for indoor use only.

•Topreventriskofreorshock,donotexposexturetorainormoisture.

•Makesuretherearenoammablematerialsclosetotheunitwhileoperating.

• The unit must be installed in a location with adequate ventilation, at least

20in(50cm)fromadjacentsurfaces.Besurethatnoventilationslotsare

blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse

and be sure to replace with same fuse size and type.

•ALWAYSsecurextureusingasafetychain.NEVERcarrythexturebyits

head. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately.

NEVER try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized tech-

nical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not

open the housing or attempt any repairs yourself. In the unlikely event

your unit may require service, please open a support ticket at www.

blizzardlighting.com/support.

Page 5

2. MEET LOOP™

MAIN FEATURES

• 7* 40W RGBW high power 4-in-1 LEDs

• 7* RGB colored rings (84* 0.2W RGB 3-in-1 LEDs total)

• Individual pixel and LED ring control

• Narrow 5° beam angle (x7)

•Blazingfast540°/270°tilt+innitepanandtilt

• 3-phase pan/tilt motors with 16-bit resolution

• Built-in auto and sound active programs

•Multiplestaticcolorpresetsandrainboweectmacros

•Variableelectronicdimming&strobeeects(1-20Hz)

• Flicker-free constant-current LED driver

• Art-NET (DMX over Ethernet) support

• 3-pin male input and 3-pin female output

• PowerCON™ compatible AC power In/Out connectors

• Protocol: USITT DMX-512, Art-NET

• 26/28/70-channel DMX modes

• 2.4 inch TFT color LCD display panel with 4x touch sensitive buttons

DMX Quick Reference (26/28/70-Channel Modes)

CH. Basic (26ch) CH. Standard (28ch) CH. Extended (70ch)

1 Pan (0-540°) 1 Pan (0-540°) 1 Pan (0-540°)

2 Tilt (0-270°) 2 Fine Pan (16-bit) 2 Fine Pan (16-bit)

3 Pan & Tilt Speed 3 Tilt (0-270°) 3 Tilt (0-270°)

4InnitePan 4 Fine Tilt (16-bit) 4 Fine Tilt (16-bit)

5InniteTilt 5 Pan & Tilt Speed 5 Pan & Tilt Speed

6 Red (0-100%) 6 InnitePan 6InnitePan

7 Green (0-100%) 7 InniteTilt 7InniteTilt

8 Blue (0-100%) 8 Red (0-100%) 8 Strobe

9 White (0-100%) 9 Green (0-100%) 9 Dimmer

10 Strobe 10 Blue (0-100%) 10 Virtual Color Wheel

11 Dimmer 11 White (0-100%) 11 Color Presets

12 Virtual Color Wheel 12 Strobe 12 Chase Patterns

13 Color Presets 13 Dimmer 13 Chase Speed

14 Chase Patterns 14 Virtual Color Wheel 14 Chase Fade

15 Chase Speed 15 Color Presets 15 Color Presets Dimmer

16 Chase Fade 16 Chase Patterns 16 Reset

17 Color Presets Dimmer 17 Chase Speed 17 LED 1 - Red

18 Reset 18 Chase Fade 18 LED 1 - Green

19 Ring Red (0-100%) 19 Color Presets Dimmer 19 LED 1 - Blue

20 Ring Green (0-100%) 20 Reset 20 LED 1 - White

21 Ring Blue (0-100%) 21 Ring Red (0-100%) -- --

22 Ring Strobe (0-20Hz) 22 Ring Green (0-100%) 21-40 LEDs 2 thru 6 (R/G/B/W)

23 Ring Dimmer 23 Ring Blue (0-100%) -- --

24 Ring Chase Patterns 24 Ring Strobe (0-20Hz) 41 LED 7 - Red

25 Ring Chase Speed 25 Ring Dimmer 42 LED 7 - Green

26 Ring Chase Fade 26 Ring Chase Patterns 43 LED 7 - Blue

-- -- 27 Ring Chase Speed 44 LED 7 - White

-- -- 28 Ring Chase Fade 45 Ring Strobe (0-20Hz)

-- -- -- -- 46 Ring Dimmer

-- -- -- -- 47 Ring Chase Patterns

-- -- -- -- 48 Ring Chase Speed

-- -- -- -- 49 Ring Chase Fade

-- -- -- -- -- --

-- -- -- -- 50 Ring 1 - Red

-- -- -- -- 51 Ring 1 - Green

-- -- -- -- 52 Ring 1 - Blue

-- -- -- -- -- --

-- -- -- -- 53-67 Rings 2 thru 6 (R/G/B)

-- -- -- -- -- --

-- -- -- -- 68 Ring 7 - Red

-- -- -- -- 69 Ring 7 - Green

-- -- -- -- 70 Ring 7 - Blue

Page 6

Figure 1: LOOP™ Pin-Up Picture

7* High Output 40W

RGBW 4-in-1 LEDs

Carry

Handle

Figure 2: The Rear Connections

3-Pin

DMX In

4-Button

Control

Panel

with 2.4"

TFT Color

Display

RJ45

3-Pin

DMX Out

RJ45

Out

Fuse

Holder

Power

Output

USB 9V

Input

Power

Input

7* LED Rings with 84*

RGB 3-in-1 LEDs (total)

Page 7

Fuse Replacement

Remove the fuse holder from of its housing. Then take out the dam-

aged fuse from its holder and replace with exact same type of fuse.

Reattach the fuse holder, and then reconnect power.

Connecting A Bunch of LOOP™ Fixtures

You will need a serial data link to run light shows using a DMX-512

controllerortorunshowsontwoormorexturessettosyncinmas-

ter/slave operating mode. The combined number of channels required

byallthexturesonaserialdatalinkdeterminesthenumberofx-

tures the data link can support.

Fixtures on a serial data link must be daisy chained in one single line.

Also,connectingmorethan32xturesononeserialdatalinkwithout

the use of a DMX optically-isolated splitter may result in deterioration

of the digital DMX signal. The maximum recommended cable-run dis-

tance is 500 meters (1640 ft). The maximum recommended number

ofxturesonaserialdatalinkis32xtures.

Data/DMX Cabling

Tolinkxturestogetheryou’llneeddatacables.Youshouldusedata-

grade cables that can carry a high quality signal and are less prone to

electromagnetic interference.

Forinstance,Belden©9841meetsthespecicationsforEIARS-485

applications. Standard microphone cables will “probably” be OK, but

note that they cannot transmit DMX data as reliably over long distanc-

es. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft.

Maximum capacitance between conductor & shield – 55 pF/ft.

Maximum resistance of 20 ohms / 1000 ft.

Nominal impedance 100 – 140 ohms

Before replacing a fuse, disconnect the power cord.

ALWAYS replace with the same type and rating of fuse.

3. SETUP

Page 8

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR connec-

tor on the other end. (Duh!)

CAUTION: Do not allow contact between the common and the

xture’schassisground.Groundingthecommoncancauseaground

loop,andyourxturemayperformerratically.Testcableswithan

ohm meter to verify correct polarity and to make sure the pins are not

grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5-pin DMX output connector, it’s no problem! you can simply use the in-

stalled5-pinDMXinputand/oroutputconnectionsfoundonthebackofyourxture(s).

Conductor 3-Pin Female (Output) 5-Pin Male (Input)

Ground/Shield Pin 1 Pin 1

Data 1- (Primary Data Link) Pin 2 Pin 2

Data 1+ (Primary Data Link) Pin 3 Pin 3

Data 2- (Optional Secondary Data Link) Pin 4 Pin 4

Data 2+ (Optional Secondary Data Link) Pin 5 Pin 5

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the DMX cable to the female connector (output) on

the controller.

Step 2: Connect the female connector of the

DMXcabletotherstxture’smaleconnector

(input). Note: It doesn’t matter which

xtureaddressistherstoneconnected.We

recommendconnectingthexturesinterms

of their proximity to the controller, rather than

connectingthelowestxturenumberrst,and

so on.

Step 3:Connectotherxturesinthechain

from output to input as above. Place a DMX

terminatorontheoutputofthenalxtureto

ensure best communication.

Page 9

Installation

Thexturecanbeinstalledontheoorrestingonitsrubberfeet,ormounted

on truss.

●Chooseasuitableplacetoputorhangtheequipmentwheninstalling.When

hangingthexture,usetheincludedclampmountingbracketswithsuitable

clampstoproperlysupporttheweightofthexture.

●Wheninstallingtheequipment,ensurethatnoammableorexplosivemateri-

als are within 1/2 meter distance.

●Pleaseaskprofessionalstoinstalltheequipment.Anyimproperinstallation

cancausepersonalinjuryormaterialdamage.

●Theequipmentmustbeplacedinaventilatedarea,atleast50cmfromthe

ground, and always ensure that the vents are not clogged.

●Mountthextureusingsuitabletypeclamps.Theclampshouldberated

toholdatleast10xthexture’sweighttoensurestructuralstability.Donot

mount to surfaces with unknown strength, and ensure properly “rated” rigging

isusedwhenmountingxturesoverhead.

WARNING:Withtheexceptionofwhenthextureispositionedon

theoor,asafetycablemustalwaysbeused.Itmustbesecurelyxed

tothesupportstructureoftheprojectorandthenconnectedtothex-

ing point at the center of the base.

Page 10

4. OPERATING ADJUSTMENTS

The Control Panel

AllthegoodiesanddierentmodespossiblewiththeLOOP™areac-

cessedbyusingthecontrolpanelonthefrontofthexture.Thereare

4 control buttons to the right of the LCD display which allow you to

navigate through the various control panel menus.

<MENU>

Is used to navigate to the previous higher-level menu item.

<ENTER>

Isusedtoselectandconrm/storethecurrentselection.

<UP>

Scrolls through menu items and numbers in ascending order.

<DOWN>

Scrolls through menu items and numbers in descending order.

The control panel display shows the menu items you select from the

menu map on page #11. When a menu function is selected, the dis-

playwillshowimmediatelytherstavailableoptionfortheselected

menu function. To select a menu item, press <ENTER>.

Use the <UP> and <DOWN> buttons to navigate the menu options.

Press the <ENTER> button to select the menu function currently dis-

played, or to enable a menu option. To return to the previous option or

menu without changing the value, press the <MENU> button.

Press <ENTER> to Menu

ADDRESS

001

Inhaltsverzeichnis

Andere Blizzard Lighting DJ-Equipment Handbücher

Blizzard Lighting

Blizzard Lighting ENIGMA M4 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Propar Z19 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting G-Max 200 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Stiletto Glo 19 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Shoqwave X6 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting VERISMO RGBALC Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Q-Stick RGBW LED Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Solar Ray Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting COLORSTORM 252 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Laser Blade G Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting MiniSystem Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck CSI Xtreme Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting TOURnado IP BAY Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting LOOK Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting SwitchBlade Micro Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Redstone 240Z Wash Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting switchblade Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Motif Fresco Series Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Hypno Beam Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ToughSTICK RGBAW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting weather system Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting TOURNADO CSI COB Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting StormChaser Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Cyc Out Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung