Blizzard Lighting REANIMATOR Bedienungsanleitung

Blizzard Lighting, LLC

www.blizzardlighting.com

Brookﬁeld, WI USA

Page 2

TABLE OF CONTENTS

Reanimator™ DMX Effect Light 1

1. Getting Started 3

What’s In The Box? 3

Getting It Out Of The Box 3

Powering Up! 3

Getting A Hold Of Us 3

Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet Reanimator™ DMX Effect Light 5

Features 5

DMX Quick Reference 5

The Reanimator™ Pinup Picture 6

3. Setup 7

Fuse Replacement 7

Connecting A Bunch Of Reanimator™ DMX Effect Lights 7

Data/DMX Cables 7

4. Operating Adjustments 8

Control Panel Menu Structure 8

DMX Mode 8

Master/Slave Mode 8

Sound Active Mode 8

Pattern Playback Adjustments 8

LED display options 8

Troubleshooting 9

5. Appendix 10

Keeping Your Reanimator™ DMX Effect Light As Good As New 10

Returns (Gasp!) 10

Shipping Issues 10

Tech Specs 11

Page 3

1. GETTING STARTED

What’s In The Box?

• 1 x Reanimator™ DMX Effect Light

• A swell IEC Power cord & DMX cable

• Warranty Card

• This Lovely User Manual

Getting It Out Of The Box

Reanimation. One of mankind’s strangest pursuits. And yet this light

ﬁxture has nothing whatsoever to do with that. It is, however, a very

cool LED animation effect. SO... now that you’ve been Reanimated™,

you should carefully unpack the box and check the contents to ensure

that all parts are present and in good condition. If anything looks as

if it has been damaged in transit, notify the shipper immediately and

keep the packing material for inspection. Again, please save the car-

ton and all packing materials. If a ﬁxture must be returned to the fac-

tory, it is important that the ﬁxture be returned in the original factory

box and packing.

Powering Up!

All ﬁxtures must be powered directly off a switched circuit and cannot

be run off a rheostat (variable resistor) or dimmer circuit, even

if the rheostat or dimmer channel is used solely for a 0% to

100% switch.

AC Voltage Switch - Not all ﬁxtures have a voltage select switch, so

please verify that the ﬁxture you receive is suitable for your local pow-

er supply. See the label on the ﬁxture or refer to the ﬁxture’s speciﬁ-

cations chart for more information. A ﬁxture’s listed current rating is

its average current draw under normal conditions. Check the ﬁxture or

device carefully to make sure that if a voltage selection switch exists

that it is set to the correct line voltage you will use.

Warning! Verify that the voltage select switch on your unit

matches the line voltage applied. Damage to your ﬁxture may

result if the line voltage applied does not match the voltage

indicated on the voltage selector switch. All ﬁxtures must be

connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, just give us a call or send an email.

We’ll be happy to help, honest.

Blizzard Lighting

W220 N1531 Jericho Ct. Suite E, Waukesha, WI 53186 USA

[email protected] | 1.866.493.6025

www.blizzardlighting.com

Page 4

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone

else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that

the line voltage you are connecting to is not higher than that stated on the de-

cal or rear panel of the ﬁxture.

• This product is intended for indoor use only.

• To prevent risk of ﬁre or shock, do not expose ﬁxture to rain or moisture.

• Make sure there are no ﬂammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least

20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse

and be sure to replace with same fuse size and type.

• ALWAYS secure ﬁxture using a safety chain. NEVER carry the ﬁxture by its

cord. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately.

NEVER try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized tech-

nical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not

open the housing or attempt any repairs yourself. In the unlikely event

your unit may require service, please contact Blizzard Lighting at sup-

[email protected].

Page 5

2. MEET The Reanimator™DMX Effect

CONTROL FEATURES

• 13 Channel DMX control

• Adjustable chase speed, length and pattern

• Variable electronic dimmer

• Built-in automated programs via DMX and master/slave

• Built-in sound active programs in standalone and DMX modes

ADDITIONAL FEATURES

• 8x8 matrix of TRI-Color LEDs (192 total LEDs)

• Over 1,000 built in patterns!

• LED control panel for easy programming

• Mounting bracket with adjustable knobs

• Durable aluminum & molded case

• No Frankenstein-like side effects (that we are aware of)

DMX Quick Reference

Channel Values What It Does

1 0 <--> 255 Graphic Selection A (0-255)

2 0 <--> 255 Graphic Selection B (+ 0-255)

3 0 <--> 255 Graphic Selection C (+ 0-255)

4 0 <--> 255 Graphic Selection D (+ 0-255)

5 0 <--> 255 Graphic Selection E (+ 0-255)

6 0 <--> 255 Graphic Selection F (+ 0-255)

7 0 <--> 255 Graphic Selection G (+ 0-255)

8 0 <--> 255 Graphic Selection H (+ 0-255)

9 0 <--> 255 Graphic Selection I (+ 0-255)

10 0 <--> 255 Animation/Loop Length

11 0 <--> 255 Animation Loop Start

0/255 = Full Number Of Patterns Dis-

played

1-254 = Begin looping with channel 10

length at pattern #1-254.

12 000 <--> 255 Animation Speed (used when Chan-

nel 13 is in Auto Mode)

13 0

001 <--> 255 Channels 1-9 Active

Auto Animation Mode (Channels 10-

12 Active)

NOTE: Channels 1-9 are cumulative, IE if channel 1 is set at 255, then

channel 2 will increment starting with graphic #257. If 1 and 2 are set

at 255, then channel 3 will increment starting with graphic #513, etc.

Page 6

Figure 1: The Reanimator™ Pin-Up Picture

Tough Aluminum Case

Reanimation Portal

(Lens)

Figure 2: The Rear Connections

AC Power In/Fuse DMX In DMX Out

Mounting

Bracket &

Knob

Power Switch LED Control Panel

Page 7

3. SETUP

Fuse Replacement

With a ﬂat head screwdriver, wedge the

fuse holder out of its housing. Remove the

damaged fuse from its holder and replace

with exact same type fuse. Insert the fuse

holder back in its place and reconnect

power.

Connecting A Bunch of Reanimator™ DMX Effects

You will need a serial data link to run light shows using a DMX-512

controller or to run shows on two or more ﬁxtures set to sync in mas-

ter/slave operating mode. The combined number of channels required

by all the ﬁxtures on a serial data link determines the number of ﬁx-

tures the data link can support.

Fixtures on a serial data link must be daisy chained in one single line.

Also, connecting more than 32 ﬁxtures on one serial data link without

the use of a DMX optically-isolated splitter may result in deterioration

of the digital DMX signal.

The maximum recommended cable-run distance is 500 meters (1640

ft). The maximum recommended number of ﬁxtures on a serial data

link is 32 ﬁxtures.

Data/DMX Cabling

To link ﬁxtures together you’ll need data cables. You should use data-

grade cables that can carry a high quality signal and are less prone to

electromagnetic interference.

For instance, Belden© 9841 meets the speciﬁcations for EIA RS-485

applications. Standard microphone cables will “probably” be OK, but

note that they cannot transmit DMX data as reliably over long distanc-

es. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft.

Maximum capacitance between conductor & shield – 55 pF/ft.

Maximum resistance of 20 ohms / 1000 ft.

Nominal impedance 100 – 140 ohms

Page 8

4. OPERATING ADJUSTMENTS

DMX Mode

Allows the unit to be controlled by any universal DMX controller.

1.) Press the <MENU> button until you reach DMX mode, which appears as

A001 on the LED Readout. Use the <ENTER> button then the <UP> and

<DOWN> buttons to choose a channel between 1and 512. Press <ENTER>

again to conﬁrm.

Master/Slave Mode (Auto/Sound Active):

Allows you to link up to 32 units together without a controller.

1.) Use standard DMX cables to daisy chain your units together via the DMX con-

nector on the rear of the units. It may be necessary to use a terminator at the

last ﬁxture. For more information about terminators, see page 8.

2.) Choose a unit to function as the Master. Select from one of the run modes,

RUN1-RUNF or sound activation. The master unit must be the ﬁrst unit. Finally,

chain the units together using DMX cable.

Master RUN1-F then <ENTER> to conﬁrm.

3.) Select slave function by using the <UP>/<DOWN> keys to reach A001 in

the menu on the slave units, and they will react in the same as the Master.

Slave A001 then <ENTER> to conﬁrm.

4.) On the master ﬁxture, use the <UP>/<DOWN>/<MENU> keys to reach

RUN1-F/Soud, which allows you to select the Master/Slave mode.

Sound active SoUd then <ENTER> to conﬁrm.

Auto mode RUN1-F then <ENTER> to conﬁrm.

Pattern Playback Adjustments:

Allows you to adjust the playback characteristics of the automatic programs.

Run1 - Run F then <ENTER> to conﬁrm.

Each program is different. Perhaps you should study them in depth and write a

short treatise on the differences. Otherwise, just enjoy them all!

L001-L255 then <ENTER> to conﬁrm.

Adjusts the number of patterns to display

F001-F255 then <ENTER> to conﬁrm.

Adjusts the number of frames to display of each animation

P000-P255 then <ENTER> to conﬁrm.

Animation speed (Slow <--> Fast)

LEon = LED Control Panel remains on

LoFF = LED Control Panel shuts off after approximately 30 seconds.

Page 9

Troubleshooting

Symptom Solution

Fixture Auto-

Shut Off Check the fan in the ﬁxture. If it is stopped or moving

slower than normal, the unit may have shut itself off due to

high heat. This is to protect the ﬁxture from overheating.

Clear the fan of obstructions, or return the unit for service.

Beam is Dim Check optical system and clean excess dust/grime. Also

ensure that the 220V/110V switch is in the correct position,

if applicable.

No Light Output Check to ensure ﬁxture is operating under correct mode, IE

sound active/auto/DMX/Etc., if applicable. Contact service

for more information.

Chase Speed

Too Fast/Slow Check to ensure proper setup of speed adjustment.

No Power Check fuse, AC cord and circuit for malfunction.

Blown Fuse Check AC cord and circuit for damage, verify that moving

parts are not restricted and that unit’s ventilation is not

obstructed

Slow Movement Verify that 220V/110V switch is in the correct position, if

applicable. Also check that speed channels are set appropri-

ately.

No Response to

Audio Verify that the ﬁxture is in “Sound Active” mode.

Adjust Audio Sensitivity, If Applicable.

Fixture Not

Responding /

Responding Er-

raticly

Make sure all connectors are seated properly and securely.

Use Only DMX Cables.

Install a Terminator.

Check all cables for defects.

Reset ﬁxture(s).

Intermittant

Lamp Check lamp for properly installation.

Relamp, lamp may have reached end of life.

Remote Doesn’t

Work Verify remote control cable is installed properly and securely.

Verify remote is correct type (CA-9 or other as applicable.)

Fixture Moving

On Its Own Verify proper mode of operation. Is the ﬁxture in “Auto”

mode?

If your problem isn’t listed, or if problems persist,

please contact support: [email protected].

Page 10

5. APPENDIX

Keeping Your Reanimator™As Good As New

The ﬁxture you’ve received is a rugged, tough piece of pro lighting equip-

ment, and as long as you take care of it, it will take care of you. That said, like

anything, you’ll need to take care of it if you want it to operate as designed.

You should absolutely keep the ﬁxture clean, especially if you are using it in an

environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled

drinks.

Cleaning the optics routinely with a suitable glass cleaner will greatly improve

the quality of light output. Keeping the fans free of dust and debris will keep

the ﬁxture running cool and prevent damage from overheating.

In transit, keep the ﬁxtures in cases. You wouldn’t throw a prized guitar,

drumset, or other piece of expensive gear into a gear trailer without a case,

and similarly, you shouldn’t even think about doing it with your shiny new light

ﬁxtures.

Common sense and taking care of your ﬁxtures will be the single biggest thing

you can do to keep them running at peak performance and let you worry about

designing a great light show, putting on a great concert, or maximizing your cli-

ent’s satistfaction and “wow factor.” That’s what it’s all about, after all!

Returns (Gasp!)

We’ve taken a lot of precautions to make sure you never even have to worry

about sending a defective unit back, or sending a unit in for service. But, like

any complex piece of equipment designed and built by humans, once in a while,

something doesn’t go as planned. If you ﬁnd yourself with a ﬁxture that isn’t

behaving like a good little ﬁxture should, you’ll need to obtain a Return Authori-

zation (RA).

Don’t worry, this is easy. Just send an email to [email protected],

and we’ll issue you an RA. Then, you’ll need to send the unit to us using a

trackable, pre-paid freight method. We suggest using USPS Priority or UPS.

Make sure you carefully pack the ﬁxture for transit, and whenever possible, use

the original box & packing for shipping.

When returning your ﬁxture for service, be sure to include the following:

1.) Your contact information (Name, Address, Phone Number, Email address).

2.) The RA# issued to you

3.) A brief description of the problem/symptoms.

We will, at our discretion, repair or replace the ﬁxture. Please remember that

any shipping damage which occurs in transit to us is the customer’s responsibil-

ity, so pack it well!

Shipping Issues

Damage incurred in shipping is the responsibility of the shipper, and

must be reported to the carrier immediately upon receipt of the items.

Claims must be made within seven (7) days of receipt.

Inhaltsverzeichnis

Andere Blizzard Lighting Beleuchtungsausrüstung Handbücher

Blizzard Lighting

Blizzard Lighting the puck Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Motif Metro Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting snokontrol Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Stiletto Z7 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Rocklite RGBAW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Northstar Spec-Z Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting PixelStorm COB Mini Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ToughPAR Satellight Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Pocket Rocket Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting the puck Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting MAX L Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting COLORSTORM Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Kontrol 5 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Node:b RGBAL Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Switch Blade X3 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Torrent 90 Beam Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Motif Risplendi 150 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting HotBox RGBW/RGBA Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Torrent Xray Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting BladeRunner RGBW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Torrent 90 Beam Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting infinipix cyclone Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting COLORISE Exa Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting the puck pro zoom Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung