Blue Robotics Thruster Commander Bedienungsanleitung
2/15/2018 Thruster Commander
http://docs.bluerobotics.com/commander/ 1/5
Thruster Commander
Introduction
Why do I need the
Thruster Commander
?
Most ESCs do not accept simple knob- or button-inputs, instead communicating via pulse-width modulation (PWM)
signals. The
Thruster Commander
converts up to two potentiometer (knob) inputs to two separate PWM output signals
that can be used to control ESCs. This allows you to run BLDC motors without the need for a complex onboard computer
system.
Why can’t I use the
Thruster Commander
with other ESCs?
Most ESCs are designed for RC airplane or multi-copter use. Motors on these craft never need to be run in reverse, so
most ESCs are uni-directional. However the
Thruster Commander
is designed to be used with bi-directional ESCs.
Because of the dierent operating natures of uni-directional and bi-directional ESCs, the signals required to stop these
types of ESCs are dierent, so the
Thruster Commander
’s safety features (which are meant to stop all attached motors)
will not work with uni-directional ESCs. For this reason the
Thruster Commander
should never be used with uni-
directional ESCs.
It is possible to upload bi-directional rmware to some standard ESCs. More information can be found in the Basic
ESC documentation (http://docs.bluerobotics.com/besc/#rmware-update-and-customization).
Important Notes
Only use the
Thruster Commander
with reversible/bi-directional ESCs (e.g. Blue Robotics ESCs
(http://docs.bluerobotics.com/besc/#rmware-update-and-customization)). Standard ESCs are not compatible with the
Thruster Commander
’s safety features. See below for more information.
Neither the
Thruster Commander
nor its included accessories are waterproof. Make sure to mount them in
locations where they will not get wet.
Deadman switches are recommended on any mobile
Thruster Commander
application.
2/15/2018 Thruster Commander
http://docs.bluerobotics.com/commander/ 2/5
ESCs are necessary for powering brushless DC (BLDC) motors (e.g. T100 & T200 thrusters),
even to run at full
speed
.
Most ESCs require a neutral input signal to complete their initialization.
This is a safety feature!
The
Thruster
Commander
will output a neutral signal when:
SWITCH is open (i.e. not connected to ground),
input potentiometers are centered, or
not enough potentiometers are connected.
Setup
Quick Start
1. Connect the power cable to the POWER connector in the top left of the board
2. Attach the potentiometer(s) to the inputs (see Modes of Operation for input congurations)
Each potentiometer’s 3-pin connector can be reversed to reverse its input
3. Attach electronic speed controllers (ESCs) to the output pins
The black/brown wire should be connected to the GND pin
These connectors should not be reversed
4. Apply 7-28 VDC power to the POWER connector and ESCs
5. To initialize the ESCs, either:
Turn the knobs to their center position, or
Turn the external switch to the o position
6. That’s it! You’re ready to go.
Modes of Operation
Mode Inputs Outputs
Single Input SPEED SPEED Both OUTPUTs
Dual Input RIGHT IN and LEFT IN RIGHT IN RIGHT OUTPUT
LEFT IN LEFT OUTPUT
Mixed Input SPEED and STEERING SPEED and STEERING Both OUTPUTs
Powering
Thruster Commander
2/15/2018 Thruster Commander
http://docs.bluerobotics.com/commander/ 3/5
The
Thruster Commander
can be powered in one of two ways: 7-28 VDC or regulated 5 VDC. 7-28 VDC power can be
supplied via the POWER connector in the top left corner of the board. This can be connected directly to any 7-28 VDC
power supply, including the batteries powering your motors. 5 VDC regulated power is available from some ESCs with
built-in battery eliminator circuits (BECs) which can power the
Thruster Commander
via the PWM cable, eliminating the
need for the 7-28 VDC power intput. These ESCs will have a third, red wire on their PWM input cables which carries the 5
VDC supply.
Note that not all ESCs with such three-wire PWM input cables have built-in BECs.
If none of your ESCs have BECs, you will need to supply either 7-28 VDC power via the POWER connector or 5 VDC
regulated power from an external regulator/BEC. Our Basic ESCs do not have built-in BECs and are not able to power the
Thruster Commander
; they will require the use of the 7-28 VDC power input.
Mounting
Thruster Commander
Two M3x0.5 holes spaced 31.75 mm (1.25”) apart on the back of each
Thruster Commander
provide a solid way to
mount it on your project. Alternatively the
Thruster Commander
can be mounted with double-sided tape. However you
mount the
Thruster Commander
, make sure it is in a location where it will stay dry, because the
Thruster Commander
and its accessories are not waterproof.
The potentiometers can be mounted through a 10 mm (3/8”) hole in a panel or box up to 2.5 mm (0.1”) thick. After
removing the nut and washer from the potentiometer, pass the potentiometer through the mounting hole from the back
of the panel or box. Replace and tighten the nut and washer, then attach the knobs to the potentiometer by tightening
the set screw onto the at section of the potentiometer shaft using the provided 1.5 mm allen wrench.
Deadman Switch/Enabling Output
To enable PWM outputs from Thruster Commander, the center SWITCH pin must be connected to ground, indicated on
the board as “GND”. This is achieved out-of-the-box with a jumper between the center and GND pins of SWITCH.
A deadman switch can be added by replacing this jumper with any normally-open (NO) momentary switch connected
between the center pin and GND. External “enable” switches can also be used. Should the switch be released or become
disconnected from Thruster Commander, the SWITCH-to-GND connection will be broken and
Thruster Commander
will
stop all connected motors.
If you are using the
Thruster Commander
on a vehicle, we highly recommend that you install a deadman switch to
prevent it from running o without you.
Operation
ESC Initialization
Most BLDC ESCs have a built-in safety feature that requires a neutral input signal (1500 µs) before they will complete
their initialization. While this reduces the chances of a thruster unexpectedly turning on and lacerating you or your
friends, it necessitates an extra initialization step at runtime.
The
Thruster Commander
outputs a neutral PWM signal to connected ESCs when:
SWITCH is open (i.e. not connected to ground),
input potentiometers are centered, or
not enough potentiometers are connected.
This condition must be held until the ESC gives a high-pitched beep (the fth beep after being powered on in the case of
the Blue Robotics BasicESC). This beep signies that the ESC has nished its initialization and is ready to accept an input.
2/15/2018 Thruster Commander
http://docs.bluerobotics.com/commander/ 4/5
If you are using a deadman switch connected to SWITCH, simply release the button until the ESC beeps to initialize.
Should you be using the included jumper, you will need to center the knobs to initialize the ESCs.
Controlling Motors
Each
Thruster Commander
contains two output channels (LEFT OUTPUT and RIGHT OUTPUT) with two sets of output
pins each. This means that the
Thruster Commander
can control two sets of motors independently. Three modes of
operation are supported:
Single Input
,
Dual Input
, and
Mixed Input
. The mode is selected by connecting potentiometers
to specic inputs. See Modes of Operation for valid combinations of potentiometer connections.
Single Input
uses a single potentiometer connected to the SPEED input to drive both the RIGHT and LEFT OUTPUTs
identically.
Dual Input
uses two potentiometer inputs, one on RIGHT IN and one on LEFT IN. The input on RIGHT IN will dictate
the output on RIGHT OUTPUT and the input on LEFT IN will dictate the output on LEFT OUTPUT.
Mixed Input
is designed for use with crafts with left and right thrusters for dierential thrust steering. In these
setups, SPEED controls the base speed of the craft and STEERING controls the dierential thrust.
The 3-pin connectors on the potentiometers are reversible, so if turning a knob runs the motors the wrong way, the
connector can be reversed to correct the problem. Note that only the potentiometer inputs are reversible; the SWITCH
and OUTPUT connectors should not be reversed. Should you be using a BLDC motor such as the T100 or T200, each
motor’s direction can be reversed by swapping any two of the three connections between the ESC and the motor.
Potentiometers can be hot-swapped. However it is advised that this only be done while the outputs are disabled
(SWITCH disconnected from GND or power to thrusters disconnected), as hot-swapping potentiometers while the
outputs are enabled may cause one or more motors to suddenly start running.
Troubleshooting
Two short blinks
Not enough potentiometers are plugged in. The Modes of Operation table shows all valid combinations of
potentiometer connections.
One long blink
Switch is not pressed/connected, or is not correctly connected. The SWITCH signal (center) pin must be connected to
ground (GND pin) by a switch or jumper for the motors to turn.
2/15/2018 Thruster Commander
http://docs.bluerobotics.com/commander/ 5/5
Inhaltsverzeichnis
Andere Blue Robotics Controller Handbücher
