BlueSpot 09109 Bedienungsanleitung

360° SWIVEL HEAD

MULTI RIVETER

(RIVET/NUT/THREADED RIVET STUDS)

User Manual

09109

Thank you for purchasing a Blue Spot Tools product, you can ﬁnd further information

on our range at www.BlueSpot.uk.com. Please ensure that you are using the product

correctly and that all guidance and cautions are followed in accordance with the

instructions. Please retain these instructions for future reference.

General Information

Please make sure that you read these instructions carefully in order to avoid injury when

using the riveter. Follow all health and safety rules and regulations. If in doubt and available

please contact a more knowledgeable source.

DO NOT use if damaged.

• Maintain tool in good and clean condition for best and safest performance.

• Keep the work area clean, uncluttered and ensure there is adequate lighting.

• Maintain correct balance and footing. Ensure the ﬂoor is not slippery and wear

non-slip shoes.

• Keep children and unauthorised persons away from the work area.

• If the riveter is damaged do not use.

• NEVER leave the riveter unattended. When you have ﬁnished using the riveter it

should be stored away in a safe place that is out of reach of children.

• NEVER try to get the riveter to perform a task that it was not made for. Do not

overload or misuse the tool.

• ALWAYS dress appropriately – clothing should be close ﬁtted and long hair tied back.

Jewellery should be removed and shoes should be worn with a non-slip sole.

• ALWAYS wear the correct eye or face protection when operating the riveter.

• ALWAYS wear approved respiratory protection. This will help protect you

from any dust.

• ALWAYS ensure you work in a well ventilated room.

• ALWAYS ensure that adjusting keys and wrenches have been removed before using

the tool. If a key or wrench is still attached when the tool is used this could

cause damage to property or cause injury.

• NEVER operate the tool if you are under the inﬂuence of drugs or alcohol as

this is dangerous.

• DO NOT operate the riveter if you are tired as this is dangerous.

• DO NOT get the riveter wet. Always use in dry locations/conditions.

• ALWAYS check and adhere to national regulations when disposing of the riveter.

Safe use

Introduction

The Blue Spot Tools 360° Swivel Head Multi Riveter (Rivet/Nut/Threaded Rivet Studs) is ideal

for professional and DIY use. Suitable for use with steel and aluminium rivet nuts, rivets and

threaded studs.The 360° swivel head makes it ideal for accessing hard to reach areas. Heavy-duty

ergonomic handles. Suitable for rivet nuts M3-M6, rivets 2.4mm to 4.8mm and stud rivets M4,

M5 and M6.

Contents: Standard rivets: 2.4mm (3/32") / 3.2mm (1/8") / 4.0mm (5/32") / 4.8mm (3/16").

Rivet nuts: M3 x 0.5 / M4 x 0.7 / M5 x 0.8 / M6 x 1. Stud rivets: M4 x 0.7 / M5 x 0.8 / M6 x 1.

Included within the box

Parts Diagram

Parts Diagram (continued)

1 Screw depth adjustment / Pull bar

2 Riveter

3 Front sleeve for nose pieces

4 4mm Nose piece

5 Front sleeve for mandrels

6 2.4mm Riveting nose piece

7 3.2mm Riveting nose piece

8 4.8mm Riveting nose piece

9 Mandrel for riveting studs – M6 x 1

10 Mandrel for riveting studs – M5 x 0.8

11 Mandrel for riveting studs – M4 x 0.7

12 Mandrel holder – M3 x 0.5

13 Mandrel for nuts – M3 x 0.5

14 Mandrel holder – M4 x 0.7

15 Mandrel for nuts – M4 x 0.7

16 Mandrel holder – M5 x 0.8

17 Mandrel for nuts – M5 x 0.8

18 Mandrel holder – M6 x 1

19 Mandrel for nuts – M6 x 1

20 Jaw Case

21 Spanners

Note – We always recommend testing this ﬁrst on a test piece of material until you become

comfortable operating the nut riveter.

1. Assemble the riveter by ﬁtting the jaw case (20) on the tool and the front sleeve for

nose pieces (3). From the body of the riveter select the correct sized nose piece (4, 6,

7 or 8) and securely attach into the front sleeve (3).

2. Open the handles of the riveter so they are as wide as they can be.

3. With the handles on the riveter remaining open, insert the rivet shaft securely into

the nose piece (4, 6, 7, or 8).

4. Place the rivet into the hole of the workpiece.

5. Close and squeeze the handles on the riveter to release the rivet into the workpiece.

6. If the rivet does not release, repeat the process again from step 2.

6. The rivet will now be securely inserted into the workpiece.

Rivets - Operation

Riveting Nose Piece

Front Sleeve For Nose Pieces

Jaw Case

Threaded Nut Rivets - Operation

Note – We always recommend testing this ﬁrst on a test piece of material until you

become comfortable operating the nut riveter.

1. Assemble the riveter by attaching the front sleeve for mandrels (5) into

the riveter.Then select the correct sized mandrel for nut (13, 15, 17 or 19)

for the size of the nut rivet that you are going to be using and securely screw

into the riveter. Screw the corresponding mandrel holder (12, 14, 16 or 18)

into the end of the front sleeve (5).

2. On the workpiece drill a hole where the diameter is slightly wider than the size

of the nut rivet diameter.

3. Open the handles of the riveter so they are as wide as they can be.

4. Securely screw the nut rivet onto the mandrel so that the end of the rivet is

level with the end of the mandrel and doesn’t protrude.To ensure that the

nut rivet is level with the end of the mandrel the mandrel holder (12, 14, 16

or 18) may need to be screwed further into the front sleeve (5).

5. Adjust the mandrel holder (12, 14, 16 or 18) to ensure it is touching the

rivet head and make sure it is securely locked into position with the lock nut.

6. Place the rivet into the pre drilled hole of the workpiece and press down so

that the nut ﬂange is held ﬁrmly against the upper face of the workpiece.

7. Close and squeeze the handles of the riveter so that the nut rivet is compressed.

8. When the rivet has formed a bulge against the workpiece unscrew the

mandrel from the nut rivet by unscrewing the screw depth adjustment

(1) on the riveter.

Mandrel Holder

Lock Nut

Mandrel For

Nuts

Front Sleeve for Mandrels

Stud Rivets - Operation

Note – We always recommend testing this ﬁrst on a test piece of material until you

become comfortable operating the nut riveter.

1. Assemble the riveter by attaching the front sleeve for mandrels (5) into the riveter.

Then select the correct sized mandrel for riveting studs (9, 10 or 11) for the

stud rivet to be used and securely screw into the riveter. Select the smallest

mandrel holder (12, 14, 16 or 18) that the threaded end of the stud rivet to be

used will slide into and screw this into the front sleeve (5).

2. On the workpiece drill a hole where the diameter is slightly wider than the size

of the stud rivet diameter.

3. Open the handles of the riveter so they are as wide as they can be.

4. Securely screw the stud rivet into the mandrel as far as it can go. Ensure the

mandrel holder (12, 14, 16 or 18) is screwed completely

down into the front sleeve (5) to enable the task ahead to be carried out.

The mandrel holder (12, 14, 16 or 18) may need to be adjusted slightly to

ensure that it is touching the rivet head and make sure it is securely locked

into position with the lock nut.

5. Place the stud rivet into the pre drilled hole of the workpiece and press down

so that the nut ﬂange is held ﬁrmly against the upper face of the workpiece.

6. Close and squeeze the handles of the riveter so that the stud rivet is compressed.

When the stud rivet has formed a bulge against the workpiece unscrew the

mandrel from the stud rivet by unscrewing the screw depth adjustment (1)

on the riveter.

7. When the stud rivet has formed a bulge against the workpiece unscrew the mandrel

from the stud rivet by unscrewing the screw depth adjustment (1) on the riveter.

Mandrel Holder

Lock Nut

Front Sleeve for Mandrels

Mandrel for Riveting

Studs

Disposal

Always check and adhere to national regulations when disposing of any tools that are no

longer functional and cannot be repaired.

• Contact your local waste disposal authority for information on how to correctly

dispose of tools.

Environmental Protection

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and

packaging should be sorted, taken to a recycling centre and disposed of in a manner which is

compatible with the environment. When the product becomes completely unserviceable and

requires disposal, drain any ﬂuids (if applicable) into approved containers and dispose of the

product and ﬂuids according to local regulations.

Contact

Find out more about the Blue Spot Tools®Lifetime Guarantee at www.BlueSpot.uk.com

Tel: 0800 093 0115

Email: [email protected]

Unit 64, Boswell Way,

Stakehill Industrial Estate,

Middleton M24 2RW

Cleaning & Maintenance

To clean just use a dry cloth to wipe over the riveter.

Storage

ALWAYS ensure the riveter and riveter nuts is stored out of reach of children.

Store the tool in a secure, dry place.

Inhaltsverzeichnis

Andere BlueSpot Nietwerkzeuge Handbücher

BlueSpot

BlueSpot M3 Bedienungsanleitung

BlueSpot

BlueSpot 09108 Bedienungsanleitung

BlueSpot

BlueSpot 09102 Bedienungsanleitung

Beliebte Nietwerkzeuge Handbücher anderer Marken

FAR

FAR RAC 182 Bedienungsanleitung

Stanley

Stanley ProSet XT4-AHR Bedienungsanleitung

Gesipa

Gesipa AccuBird Pro Leitfaden

Gesipa

Gesipa taurus 1 Leitfaden

YATO

YATO YT-3617 Bedienungsanleitung

CHIEF

CHIEF PNP 90 UN 2.0 Bedienungsanleitung

Gage Bilt

Gage Bilt GB150 Bedienungsanleitung

JRP

JRP NB80A Bedienungsanleitung

Würth

Würth ANG 14 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand 127 Bedienungsanleitung

Arconic

Arconic MARSON MP-4V Bedienungsanleitung

Sealey

Sealey CP316 Bedienungsanleitung

Silver Eagle

Silver Eagle SE314 Bedienungsanleitung

Würth

Würth HES 510 N Kurzanleitung

Stanley

Stanley EZM1000 Fehlerbehebungshandbuch

Stanley

Stanley PROSET PB3400 Bedienungsanleitung

HS-Technik

HS-Technik NutBee NBLS-21 Bedienungsanleitung

Gesipa

Gesipa PowerBird Pro Gold Edition Leitfaden