Bluetti EP600 Bedienungsanleitung

EP600 Quick Guide

1. Overview 2. Installation

2.2 Installation requirements 2. 3 Wall mounting

EP600 1 PV input 1 5 LED Indicator 9 Waterproof and

ventilate valve 13 USB Port

2PV input 2 6 Signal Port 1 10 COM

Communicate Port 14 Load Port

3 DC ON/OFF 7 Signal Port 2 11 CT Input Port 15 Grid Port

4Battery

Negative

8Battery

Positive

12 DRMs Port 16 Ground

3. Connecting cables

3.1 overview

3.2 Connect the communication cable

B500 1 Negative output cable port

(Upper)

6 Positive output cable

port (upper)

11 Ground wire

port(Upper)

2 Signal connection cable port

(Upper)

7 Inverter signal cable

port

12 Ground wire

port(Bottom)

3 Signal cable port (Bottom) 8Waterproof and

breathable valve

13 Waterproof and

breathable valve

4 Negative output cable port

(Bottom)

9 Positive output cable port (bottom)

Manual mechanical switch

ON/OFF Switch

2. Installation

2.1 overview

NOTE: The Meter is only used for the situation of installed three phase solar PV inverters, it is provided By BLUETTI and it

is free.

NOTES:

1. This document is for quick guidance installation only. For details, please refer to the installation and User Manual.

2. Machine damage caused by failure to follow the content is not covered by the warranty.

Note:Make sure the router used for EP600 applies to WiFi of

IEEE 802.11 b/g/n, 2.4GHz, please turn off the 5G option

3.3 Connect the Ground Cable 3.5 Connect the Batteries and EP600 3.6 Connect PV cable 3.7 Connection CT

Port Define Cable pec.

PV1+：To solar

panel positive

PV1-：To solar

panel negative

PV1 PE：PV1 to

solar panel ground

Conductor

cross-

sectional

area

2.5mm2～

4mm2

PV2+：To solar

panel positive

PV2-：To solar

panel negative

PV2 PE：PV2 to

solar panel ground

NOTES:

1.Make sure the arrow inside the CT points to the grid.

2.Pay attention to the phase sequence when connect the

CT: L1 to R, L2 to S, L3 to T.

3.The CT connect to the EP600 must be installed onto the

L1/L2/L3 cables of the residential main circuit breaker.

3.4 Connect the GRID and BACKUP Cable

3.7 Connection Transfer Switch

Transfer switch is necessary for building a partial residential

backup system.

NOTES:

1.The neutral cable from the BACKUP interface of EP600

cannot be connected to the neutral cable of the public grid.

2.Connect the L1/L2/L3/N wires from EP600 BACKUP to the

pin 2(L1), pin 6(L2), pin 10(L3), pin 14(N) of transfer switch;

3.Connect the L1/L2/L3/N wires from public grid to the pin

4(L1), pin 8(L2), pin 12(L3), pin 16(N) of transfer switch;

4. Move away the wires of the circuit breaker connected to

essential appliances, then connect pin1(L1), pin 5(L2),

pin9(L3), pin 13(N) of transfer switch.

NOTE: Please check the solar PV open circuit voltage

, it must be less than 500V.

NOTE:It is forbidden to connect the grid cable to

the BACKUP interface of EP600.

3.8 Electrical connection modes 1: DC coupling 4. Power on

Step1: Switch on the DC circuit breaker on each B500

battery pack.

Step2: Press and hold the power button of any battery pack

for 3 seconds and the green indicator on the button lights

up.

Step3: Wait for 40 seconds until the green indicator of the

inverter is always on.

Step4: When connecting to the sloar panel ,please switch on

the DC circuit breakers on EP600.

Step5: Switch on the AC circuit breakers connected to the

EP600 grid port.

Step6: Power on the system via the BLUETTI app. For

details, please refer to Setting section on App Manual.

Step7: Check the voltage of BACKUP.

Step8: Switch on the AC circuit breakers connected to the

EP600 load port.

END,Then you can check the EP600 system status through

the app.

3.9 Electrical connection modes 2: AC coupling

5. Service and contact

After-sales address in EU ：Lise-Meitner-Strasse 14, 28816

Stuhr, Germany

NOTE:

The Meter is only applicable to the case where the PV grid-tied inverters have been

installed.

1) Connect the cables of UA UB UC UN to the L1/L2/L3/N of the PV inverter,

2) Connect the cables of the CT to the Meter and tied to the wires of L1/L2/L3/N of the PV

inverter.

3) Please connect the 485-A red wire to pin 21,485-B black wire to pin 22.

Andere Handbücher für EP600

Andere Bluetti Lagerung Handbücher

Bluetti

Bluetti EP760 Bedienungsanleitung

Bluetti

Bluetti EP900 Bedienungsanleitung

Bluetti

Bluetti EP800 Bedienungsanleitung