Blyss NDY-19MA-E Bedienungsanleitung

Fireplace Heater

ORIGINAL INSTRUCTIONS -NDY-19MA-E V01 - 25-06-2018

NDY-19MA-E

EAN: 3663602673026

WARNING: Read the instructions before using the product!

2 3

NDY-19MA-E NDY-19MA-E

Getting Started . . .

Safety warnings

PLEASE READ THE FOLLOWING

INSTRUCTIONS CAREFULLY

BEFORE USING THE APPLIANCE.

CAUTION - Fire, electric shock, physical injury and material

damage hazards.

To use the appliance, always follow the instructions for

assembly, use and maintenance as well as usage cautions.

3. Carefully read and retain these instructions.

Before connecting the appliance, be sure that the mains

voltage available matches that specied on the rating plate.

THIS APPLIANCE MUST BE WALL MOUNTED. IT IS NOT

SUITABLE FOR USE AS A FREE STANDING APPLIANCE.

Operating the product in any other position could cause a

hazard.

6. There may be trace of odour during the rst few minutes of

initial use. This is normal and will quickly disappear.

The heater is hot when in use .To avoid burns, do not let

bare skin touch any hot surface.

Keep combustible material such as furniture, cushions,

bedding, paper, clothes, curtains etc. at least 1m away from

the heater.

Do not use the heater in areas where ammable liquids are

stored or where ammable fumes may be present.

10. Do not cover or obstruct any of the heat outlet grilles or the

air intake openings of the heater.

11.

Do not use the heater in any room where there is explosive

gas or while using inammable solvents, varnish or glue.

Let’s

get started...

These instructions are for your safety. Please read through them

thoroughly before use and retain them for future reference.

Getting Started... 02

Safety information 03

Before you start 06

Your product 06

Installation 07

In more detail... 9

Operation 9

Technical specication 13

Cleaning and maintenance 15

Recycling and disposal 17

Safety information

4 5

NDY-19MA-E NDY-19MA-E

Safety information Safety information

Getting Started . . .

12.

Keep the heater clean. Do not allow any objects to enter any

ventilation or exhaust opening as this may cause electric

shock, or re or damage to the heater.

13. Always unplug or disconnect the appliance from the mains

power supply when not in use or when moving or cleaning it.

14. Do not pull the cord to unplug the heater.

15. Do not immerse the cord, plug or any part of the appliance

in water or any other liquid.

16.

Do not attempt to repair, disassemble or modify the appliance.

There are no user-serviceable parts inside.

17.

The heater must not be located immediately below a socket-

outlet.

18. This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by

children without supervision.

19.

Children of less than 3 years should be kept away unless

continuously supervised. Children aged from 3 years and less

than 8 years shall only switch on/off the appliance provided

that it has been placed or installed in its intended normal

operating position and they have been given supervision or

instruction concerning use of the appliance in a safe way

and understand the hazards involved. Children aged from 3

years and less than 8 years shall not plug in, regulate and

clean the appliance or perform user maintenance.

20.

If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualied persons

in order to avoid a hazard.

21. CAUTION — Some parts of this product can become very

hot and cause burns. Particular attention has to be given

where children and vulnerable people are present.

22. CAUTION – If using an extension lead please ensure you

do not exceed the maximum rated running wattage/load of

the extension lead.

23. This IPX0 appliance cannot be installed in a bathroom.

24.

CAUTION: In order to avoid a hazard due to inadvertent

resetting of the thermal cutout, this appliance must not be

supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched on

and off by the utility.

25.

Regarding the installation and maintenance information

refer to page 14-17.

26. Do not use this heater in the immediate surroundings of a

bath, a shower or a swimming pool.

27. Means for disconnection having a contact separation in all

poles must be incorporated in the xed wiring in accordance

with the wiring rules.

WARNING! In order to avoid overheating, do not cover

the heater.

WARNING! DO NOT COVER THIS APPLIANCE WITH

ITEMS SUCH AS CLOTHING, BLANKETS OR PLACE

IT NEXT TO CURTAINS OR NETS/BLINDS.

6 7

NDY-19MA-E NDY-19MA-E

Getting Started . . .

Assembly

This product comes fully assembled, before using please ensure that all components

and xings are secure, and make sure the appliance is in perfect condition before

operation.

You will need

Screwdriver x 1

AAA 1.5V Battery x 2

Intended use

1. This product is intended for indoor use only. It is not intended for commercial use.

2. This product is intended for xed installation only. Do not use it as a free standing

heater.

This product contains no user serviceable parts and requires little maintenance.

Leave any servicing or repairs to qualied personnel only. The LEDs contained in

this product are non-replaceable.

4. Before connecting the appliance to the power supply, check that the power supply

voltage and current rating corresponds with the power supply details shown on the

appliance rating label.

Installation

Installation steps (page 7-8)

> Ensure that the appliance is switched off and disconnected from the socket outlet.

CAUTION! Make sure not to damage any wiring that could be potentially behind

the back panel e.g. mantel.

1. Secure the appliance to the wall using the supplied brackets and screws.

Press each bracket against the inside wall of the appliance, ensuring that the bracket

is located as high as possible.

3. Mark the location of the 2 holes on the inside wall.

Carefully drill two 5 mm deep holes using a 2 mm drill bit. Do not exceed 5 mm depth

to prevent damage to the outside surface of the appliance. This hole is to ensure

that you do not crack the wood when using the self tapping screws to x the bracket

onto the appliance.

5. Place the bracket on the 2 holes and secure it in place with 2 screws (C).

Thermal Cut-Out

1. CAUTION! This product has one non-self-resetting overheat protection devices. In

the event that the heater stops working as a result of overheating take the following

immediate steps: switch the electricity off at the socket and remove the plug. Remove

any objects that are covering the product.

2. CAUTION! Do not touch the heater as it will be hot.

Set the heater switches to O (off position) and leave the heater to cool. Once

completely cool, reconnect the heater and switch it on.

Things to check before you start

1. For domestic use only.

2. Never allow children or persons unable to operate the appliance safely to use this

appliance without supervision.

3. Please dispose of plastic bags carefully and keep them away from children.

IMPORTANT: When in use never cover the heater in any way or place it close to

combustible materials. The heater will get hot, never touch it whilst in use. Always

keep children and pets at a safe distance and never leave unsupervised in a room

with a heater that is working.

Your product

[01] x 1

[A] x 2 [B] x 2 [C] x 4

[02] x 1

[D] x 2

Your product / InstallationSafety information / Before you start / Your product

8 9

NDY-19MA-E NDY-19MA-E

In more detail . . .

Getting Started . . .

Repeat this for the other side of the appliance, so that you have 1 bracket on the

left and on the right of the appliance.

Carefully place the appliance on the wall and mark the holes of the brackets on

either side.

8. Using a 8 mm diameter drill bit, drill two 40 mm deep holes where the two markings

are, and place the wall plugs (A) in the holes.

Place the replace aligning the two holes with the brackets, and use 2 screws (B)

to x the replace to the wall.

10.

The replace must be secure so that it is not possible to pull away using normal loads.

11.

WARNING: This product is heavy. Failure to install this product securely and in

accordance with these instructions could lead to a serious or fatal injury!

[A] 4

[C]

[D]

[01]

[B]

The controls

Switching on/off

Use the on/off switch to power on the appliance (set it to standby mode).

In standby mode, the appliance can be operated either manually, by the switches located

on the front bottom left hand side of the appliance or by the supplied remote control.

Manual control

NOTE: The appliance only starts working, if the set temperature is higher than

the ambient room temperature.

Appliance powered off

Appliance powered on, set to standby mode

> Press to switch the ame effect on/off.

Press and hold to toggle between 5 different ame

dim levels

Press to activate low level heating (1000 W)

Press to activate high level heating (2000 W)

Installation Operation

[C] x 4

[D] x 2

[01] x 1

[B] x 2

[A] x 2

10 11

NDY-19MA-E NDY-19MA-E

In more detail . . .

Remote control

NOTE: The appliance should be powered on using the on/off switch before it

can be operated using remote control.

- Switch the appliance on

- Set to standby mode

Go up in menu

(change day)

Set timer key

Cancel key

Timer on/off key

Toggle between 5 different

ame dim levels

Press to activate low

level heating

Press to activate

high level heating

Go down in menu

(change day)

Set day/time

Conrm selection

- Decrease temperature

- Decrease hour/minute

- Increase temperature

- Increase hour/minute

Set automatic heating

mode

> The remote control requires 2x AAA size batteries (not included)

Open the battery compartment by sliding the cover down and insert the batteries

noting the polarity indicated in the battery compartment.

> Keep batteries out of reach of children.

> Remote control operations are identical to the functions on the control panel.

> The remote control must be point directly at the sensor on control pad.

Display

Temperature/

timer number

Standby mode icon

Timer off

Timer on

Time/temperature display

Automatic heating mode

Flame dim level

Heating level

- low heating level

- high heating level

Day of the week

Timer icon

Settings

Setting weekday and time

Press the key. When the date is ashing press the “▲” or “▼” key to select the day.

2. Press the key again, then press the “+” or “-” key to set the hour.

3. Press the key again, then press the “+” or “-” key to set the minute.

4. Press the key to conrm the setting.

Setting temperature

NOTE: This setting is only applicable for the temperature in standard heating

mode, not for the temperature in the timer mode. The default set temperature

is 20 °C.

The appliance only starts working, when the set temperature is higher than

the room temperature.

Press the “+” or “-” key to set the temperature, which ranges from 15 to 30 °C.

After the temperature setting has been completed, the display ashes about 5 seconds,

then shows the room temperature.

Operation Operation

12 13

NDY-19MA-E NDY-19MA-E

In more detail . . .

Setting timer

• Up to 10 different timer settings can be programmed.

• Each timer setting has its date, power-on time and power-off time.

• The maximum duration of each timer setting is 23 hours 50 minutes.

• If the power-off time of the timer setting falls on the following day, it is unnecessary

to set the date – just set the power-off time.

1. Press the key, the timer number starts blinking (01-10).

2. Press the “+” or “-” key to select a timer number.

3. Press the key. The cursor on the left side of the day blinks.

Press the “▲” or “▼” key to move the cursor to the corresponding day. Press the “+”

key to add a corresponding day, or press the “-” key to delete a day.

5. Press the key to set the on time. The hour digit starts blinking.

6. Press the “+” or “-” key to set the hour.

7. Press the key. The minute digit starts blinking.

8. Press the “+” or “-” key to set the minute.

9. Press the key, to set the off time. The hour digit starts blinking.

10. Press the “+” or “-” key to set the hour.

11. Press the key. The minute digit starts blinking.

12. Press the “+” or “-” key to set the minute.

13. Press the key. The temperature digit starts blinking.

14. Press the “+” or “-” key to set the temperature.

15. Press the key to continue with the Timer setting or press the key to conrm

the setting.

Viewing the timer setting

1. Press the key.

2. Press the “+” or “-” key to check the power-on time of the set timers one by one.

3. To check the power-off time, press the “▲” key.

4. Press the “+” or “-” key to check the power-off time of the set timers one by one.

5. To delete selected setting, press the “C” key.

Activation timer

Press the key to activate the timer function.

NOTE: When the timer is active, the heating level must be manually selected.

If the heater function is not selected, only the ame effect goes on at the set

power-on time.

Automatic heating mode

Press the “IC” key to activate automatic heating mode. The “AUTO” icon appears on

the display.

When the automatic heating is turned on, the replace automatically activates/changes

the heating level depending on the set temperature and the ambient room temperature.

Technical specication

Model: NDY-19MA-E

Rated voltage: 220 - 240 V~, 50 Hz

Rated power input: 2000 W

Class I product, must be connected to earth.

Conforms to all relevant European Directives.

For indoor use only.

yyWxx

Manufacturing date code; year of manufacturing (20yy) and week

of manufacturing (Wxx).

Model identier(s): NDY-19MA-E

Item Symbol Value Unit Item Unit

Heat output Type of heat input, for electric storage local

space heaters only (select one)

Nominal heat

output

Pnom 2 kW manual heat charge control, with

integrated thermostat

Not

applicable

Minimum

heat output

(indicative)

Pmin 1 kW manual heat charge control with

room and/or outdoor temperature

feedback

Not

applicable

Maximum

continuous

heat output

Pmax,c 2 kW electronic heat charge control with

room and/or outdoor temperature

feedback

Not

applicable

Operation / Technical specications

Operation

14 15

NDY-19MA-E NDY-19MA-E

In more detail . . .

Cleaning and maintenance

Auxiliary

electricity

consumption

fan assisted heat output Not

applicable

At nominal

heat output

elmax 0.014 kW Type of heat output/room temperature control

(select one)

At minimum

heat output

elmin 0.014 kW single stage heat output and no room

temperature control

[no]

In standby

mode

elSB 0.48 W Two or more manual stages, no room

temperature control

[no]

with mechanic thermostat room

temperature control

[no]

with electronic room temperature

control

[no]

electronic room temperature control

plus day timer

[no]

electronic room temperature control

plus week timer

[yes]

Other control options (multiple selections

possible)

room temperature control, with

presence detection

[no]

room temperature control, with open

window detection

[no]

with distance control option [no]

with adaptive start control [yes]

with working time limitation [no]

with black bulb sensor [no]

Contact details Kingsher International Products Limited,

3 Sheldon Square, London, W2 6PX, United Kingdom

Cleaning and maintenance

1. Switch off and unplug from the power supply before cleaning.

Using a soft, moist cloth, with or without a mild soap solution, carefully clean the

exterior surface of the product.

CAUTION: Allow the product to completely cool before handling or cleaning it.

Do not allow water or other liquids to run into the interior of the product, as this could

create a re and/or electrical hazard.

We also recommend the periodic cleaning of this appliance by lightly running a

vacuum cleaner nozzle over the guards to remove any dust or dirt that may have

accumulated inside or on the unit.

CAUTION: Do not use harsh detergents, chemical cleaners or solvents as they may

damage the surface nish of the plastic components.

NOTE: This product contains no user serviceable parts and requires little

maintenance. Leave any servicing or repairs to qualied personnel only. The

LEDs contained in this product are non-replaceable.

Battery replacement

2 x AAA, 1.5 V

Storage

The product can be stored in the off-season, we recommend using the original (or

appropriately sized) box. It is important to keep it in a safe, dry location.

Transportation

It is recommended to transport the product in the original packaging that is appropriately

secured. Avoid excessive vibrations.

Technical specications

NDY-19MA-E

In more detail . . .

NDY-19MA-E

Plug replacement

This appliance is supplied with a BS1363 pin plug tted with a 13 Amp fuse. Should the

fuse require replacement, it must be replaced with a fuse rated at 13 Amp and approved

to BS1362. In the event the mains plug has to be removed/replaced for any reason,

please note: IMPORTANT: The wires in the mains lead are coloured in accordance with

the following code:

Blue or Black – N - (Neutral)

Brown or Red – L (Live)

Green / Yellow – E / (Earth)

Connect Blue

to N (Neutral)

Connect Green /

Yellow to E (earth)

13 AMP fuse

approved to

BS 1362

Brown L (Live)

Cable grip

Outer sleeve

rmly clamped

As the colours of the wires in the mains leadof this appliance may not correspond with

the coloured markings identifying the terminals in your plug, proceed as follows. The

blue wire must be connected to the terminal marked with an N or coloured black. The

brown wire must be connected to the terminal marked with an L or coloured red.

WARNING! Never connect live or neutral wires to the earth terminal of the plug.

Only t an approved 13 Amp BS 1363 or BS 1363/A plug and the correctly rated fuse.

If in doubt, consult a qualied electrician.

NOTE: If a moulded plug is tted and has to be removed take great care

in disposing of the plug and severed cable, it must be destroyed to prevent

engaging into a socket.

Recycling and disposal

This symbol is known as the 'Crossed-out Wheelie Bin Symbol'.

When this symbol is marked on a product or battery, it means that

it should not be disposed of with your general household waste.

Some chemicals contained within electrical/electronic products or

batteries can be harmful to health and the environment.

Only dispose of electrical/electronic/battery items in separate

collection schemes, which cater for the recovery and recycling of

materials contained within. Your co-operation is vital to ensure

the success of these schemes and for the protection of the

environment.

Recycling and disposalCleaning and maintenance

16 17

Distributor:

B&Q plc,

Chandlers Ford, Hants,

SO53 3LE United Kingdom

www.diy.com

SFD Limited

Trade House, Mead Avenue

Yeovil

BA22 8RT, United Kingdom

www.screwx.com

Manufacturer, Fabricant, Producent,

Hersteller, Producător, Fabricante:

Kingsher International Products Limited

3 Sheldon Square

London

W2 6PX

United Kingdom

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Blyss Kamin im Innenbereich Handbücher

Blyss

Blyss EL1716B Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung