BM PRO JHub Bedienungsanleitung
TEAMBMPRO.COM
OWNER’S MANUAL
JHub TABLET
TEAM
BMPRO
.COM
POWERING YOUR ADVENTURES
With over 50 years’ experience in power
solutions combined with manufacturing
and design facilities in Melbourne,
Australia, BMPRO are the leading
experts in RV power management.
Inspired by the great outdoors, we
have created a range of rugged, smart
and reliable products to power your
adventures.
Our range of battery, power and RV
management and control systems gives
you peace of mind when you are on the
road, so that you can relax in even the
most far-flung destinations, knowing
you have control over your power
needs.
To learn more about the BMPRO range
of products, please visit our website
teambmpro.com
CONTENTS
SAFETY PRECAUTIONS 4
ABOUT THE JHub TABLET 5
What’s Included 5
DESCRIPTION OF PARTS 6
JHub Tablet 6
JHub Application 7
USING YOUR JHUB TABLET 10
Pairing the JHub Tablet to the ControlNode 10
Configuring a New Battery 13
Controlling Loads with the JHub App 14
Pairing and Using Sensors 15
Pairing SmartSense Gas Bottle Level Sensor 15
Pairing SmartPressure Tyre Sensor 17
Pairing SmartTemp Temperature Sensor 19
Setting Sensor Alarms 21
SERVICING 22
FAQS AND TROUBLESHOOTING 23
App and Tablet 23
Battery 23
ControlNode 24
Date and Time 24
Load Control 25
Pairing 27
APPENDICES 29
Specifications 29
WARRANTY TERMS AND CONDITIONS 30
Copyright © 2019
MANUAL PART 034722
REV 7.0
Designed by BMPRO, one of Australia’s leading power solution experts, the BMPRO range of
products are proudly Australian-Made in Melbourne, Victoria and represent a high-quality
product that will provide years of service.
DISCLAIMER: BMPRO accepts no liability for any loss or damage which may occur from
the improper or unsafe use of its products. Warranty is only valid if the unit has not been
modified or misused by the customer.
Do not drop or vigorously shake the product as this may cause damage. Do not shock
the product, its accessories or batteries as this may cause the product or battery to
fail, catch fire or explode.
Please note that your battery can only reach top performance level only after it has
been fully charged and discharged two or three times.
Keep this product and your battery dry and do not expose it to water or water vapour.
Do not use this product in areas where it can fall into water, such as, for example,
near a pool, pond or bath. Do not operate this product or your battery with wet
hands. Contact with water will cause the product or your battery to short-circuit or
corrode and may result in electric shock.
Do not use this product in environments that are excessively hot, cold, dusty or
humid or where it will be exposed to magnetic fields or long periods of sunshine.
Such exposure may cause the product or your battery to fail, catch fire or explode.
Product specifications are subject to change and improvement without notice.
SAFETY PRECAUTIONS
Please read the Safety Precautions before installing or using the JHub Tablet.
Be sure to observe all precautions without fail. Failure to observe these instructions
properly may result in personal damage, or personal injury which depending on the
circumstances may be serious and cause loss of life.
4
ABOUT THE JHUB TABLET
BMPRO’s JHub Tablet is a portable app-driven RV monitor and control hub that
operates with BMPRO’s J35 Battery Management System via the ControlNode.
The JHub Tablet provides a new level of comfort and knowledge about the caravan
including:
9The freedom to operate caravan features, including lights, hot water, slide-out
and water pump from anywhere in the caravan
9Full visibility and control of the caravan’s battery system including battery
status, power consumption and available charge sources
9Monitoring of clean and dirty water tanks and caravan temperature
9Option to monitor a range of Bluetooth connected devices via BMPRO’s
SmartConnect
WHAT’S INCLUDED
Included with this product are:
9JHub Tablet
9JHub Tablet Owner’s Manual
5
DESCRIPTION OF PARTS
1. Power
Turn JHub Tablet on/off and turn tablet screen on/off.
2. microUSB Input
To charge the JHub Tablet.
3. Return
Navigate to previous page.
4. Main Screen
Navigate to JHub Tablet’s main screen.
5. Recent Applications
Display a list of recently used/background applications
JHub TABLET
Figure 1: The JHub Tablet 3 4 5
1
2
6
JHub APPLICATION
HOME SCREEN
1. Settings Menu
Access to the JHub App settings and functions and Owner’s Manual.
2. Pairing Status
Indicates pairing status between JHub Tablet and ControlNode.
Table 1: Bluetooth connectivity status indications
Please be aware that when
Bluetooth is disconnected, any
information displayed on the
JHub may be incorrect. When
the Bluetooth connection is
established, the JHub will update
to reflect correct battery usage.
BLUETOOTH ICON CONNECTION STATUS
CONNECTED
CONNECTING
DISCONNECTED
RED
YELLOW
BLUE
Figure 2: The JHub Home Screen
215 4 5 6 7
11 16
12
8 9
1
3
10
13 14
7
3. Battery Icon
Enables Sleep Mode the J35 will provide power to the CAN bus. This allows you
to continue to monitor battery consumption from the battery monitor. However,
power to the load terminal block will be turned off and you will not be able to use
your battery monitor to power caravan loads.
To exit Sleep Mode, start battery charging. The J35 will exit Sleep Mode
when the battery is sufficiently charged. Upon exit of Sleep Mode, the J35 will
automatically return to its previous state of operation.
When in Sleep Mode you may temporarily turn on caravan loads by cycling the
caravan’s Load Isolation Switch. This feature allows you to retract slide-outs or
electric steps should you need to pack your caravan. This temporary switch on of
the caravan loads may also be done by pressing the Battery icon on your battery
monitor.
4. Slide-In/Out Control
Where fitted, controls the caravan’s slide-in/out mechanism
5. Area 1 Master Light Switch
6. Area 2 Master Light Switch
7. Area 3 Master Light Switch
8. Hot Water Heater Switch
9. Water Pump Switch
10. Battery Status
11. Battery State of Charge
Indicator providing a visual display of the battery’s power capacity.
Displayed only if a battery is connected to the J35.
Table 2: Battery Status Indications
BATTERY STATUS
CHARGING The J35 is charging the battery —
denoted by the lightning symbol
DISCHARGING Indicates the caravan’s battery is being consumed and the
time remaining before the battery is completely discharged
IDLE Indicates that no current is flowing
into or out of the caravan battery
8
13. Source
Indicates external power sources available for charging your battery and
powering the caravan loads.
14. Consumption indicators
15. Temperature
Indicates the temperature measured by the wired temperature sensor
connected to the ControlNode.
Table 3: Consumption indicators
BATTERY Indicates the charging/discharging current of the
battery connected to the J35
OUTPUT Indicates the current delivered to the caravan’s loads.
VOLTAGE Caravan battery voltage
Figure 3: Renaming and changing tank type
12. Tanks
Monitor water levels of up to 4 water tanks. Tank properties, such as name,
water-source (i.e. fresh or grey water) are configurable via the Settings Menu.
When a ‘Fresh’ tank is almost empty, the lowest water level segment of the
tank will turn red to indicate the tank is almost out of water.
The water level segments on a ‘Grey’ tank will turn red when the tank is full
and needs emptying.
Note: The user has the ability to change the title and type of each tank
(i.e. dirty/clean) via the Settings menu from the home screen.
9
Figure 4: SmartConnect Screen
USING YOUR JHUB TABLET
PAIRING THE JHUB TABLET TO THE CONTROLNODE
The JHub Tablet will have been paired to the ControlNode at the Jayco dealership.
Once paired, Bluetooth connectivity between the JHub Tablet and ControlNode
will automatically occur whenever the JHub Tablet is on and charged and within
Bluetooth range of the ControlNode.
However, if you ever need to pair the JHub Tablet to the ControlNode:
1. Ensure that the ControlNode is connected to the J35.
2. Ensure that the J35 is powered ON
3. Ensure that the JHub’s Bluetooth is ON
4. Press the pairing button on the ControlNode. The LED will start
flashing green which means that you have 30 seconds to pair your JHub.
5. If the app is not automatically launched, launch the JHub app on your JHub
and press the “Scan” button and it will now search for the nearby ControlNode
devices. Once this is complete, a list of the available ControlNode devices ready
for connection will appear.
Note: Before starting a scan, the JHub App may request access to the device’s
location-always allow.
16. SmartConnect
SmartConnect allows you to integrate and monitor gas bottle, tyre and
temperature sensors.
10
Inhaltsverzeichnis
