BOB Duallie Infant Car Seat Bedienungsanleitung

This product is compatible

with strollers that have a serial

number within the range

listed. Using this product on

strollers with incompatible

serial numbers may lead

to injury or death.

Main Bar

Right Tray

Arm

Restraint Belt M

Accessory Bar

Left Tray

Bonnet Spacer 2x

Restraint Belt F

Sharp Screw 2x

Pivot Nut 2x

Pivot Screw 2x

Arm

Loctite 262

Pivot Plug 2x

Bonnet Screw 2x

TAKE TIME  READ AND UNDERSTAND INSTRUCTIONS COMPLETELY!

Before attempting to assemble or use your new Duallie ICSA, read and understand these assembly

instructions completely, as well as the warnings at the end of this document, to insure proper

assembly and safe operation.

If you are unclear on any point, contact your dealer or BOB before use.

Duallie Infant Car Seat

Adapter Instructions

TOOLS NEEDED:

To perform the

installation, you need a

Phillips screwdriver, 4mm

hex (Allen) wrench, an

8mm socket wrench and

a rag or paper towel.

Congratulations on

your purchase of the

BOB Duallie Infant Car

Seat Adapter (ICSA). It

is designed to allow the

attachment of an Infant Car

Seat to your BOB Duallie

Stroller. Please refer to the

tables at right for details

of compatible strollers and

car seats.

Car Seat Compatibility

Brand Model Year (s)

Britax Companion ™ 2003-2008

Graco®Snug Ride®2003 and newer

Graco®Snug Ride®30 2010 and newer

Graco®Snug Ride®32 2008 and newer

Graco®Snug Ride®35 2009 and newer

Graco®Safe Seat ™ 2006 and newer

Peg Perego®Primo Viaggio™ 2003 and newer

Peg Perego®Primo Viaggio SIP™ 2006 and newer

Peg Perego®Primo Viaggio SIP™ 30/30 2007 and newer

BOB®Stroller Compatibility

Model Serial Number Range

Duallie®AD000001 - AD999999

Ironman®Duallie AE000001 - AE999999

Revolution®Duallie AH000001 - AH999999

Revolution Duallie 12" AL000001 - AL999999

Stroller Strides®Duallie AM000001 - AM999999

OMA18B P1

SET PARKING BRAKE. See the “Parking Brake”section of your stroller owner’s manual.

REPEAT STEPS

3 though 6 for other side.

REASSEMBLE CANOPY

Insert new longer

bonnet screw through

washer, stroller tube,

spacer, puck with

curved stay and puck

with straight stay.

APPLY LOCTITE 262

ATTACH LOCKNUT

Apply a drop

of Loctite 262 to

exposed threads

of screw.

RAISE HANDLE BAR

Use an 8mm socket wrench on

locknut and a 4mm hex wrench

on bonnet screw head.

Turn socket wrench counter-

clockwise.

Remove locknut and disassemble.

Use an 8mm socket wrench on

locknut and a 4mm hex wrench

on screw head.

Turn socket wrench clockwise.

TIGHTEN FIRMLY (3.7 N.m)

Bonnet

Spacer Bonnet

Screw

COLLAPSE HANDLE BAR

INSTALL CANOPY SPACER

REMOVE EXISTING BONNET SCREW

Squeeze red handles and

fold handle bar forward.

curved

straight

pucks

SEE WARNINGS

at end of document.

OMA18B P2

Rotate arms into an

upright position.

POSITION ARMS

ATTACH MAIN BAR

Rest ICSA assembly on stroller seat.

Place pivot screws and

pivot plugs on stroller seat

next to ICSA.

PREPARE TO ASSEMBLE

INSTALL PIVOT NUT TIGHTEN PIVOT NUT

Use a Phillips screwdriver

to tighten the pivot screw

clockwise, while holding the

pivot nut.

Reach under fabric seat.

Thread pivot nut onto

pivot screw as shown.

REPEAT STEPS

14 and 15 for other side.

INSERT PIVOT SCREW

...just far enough to keep the

pivot plug from slipping o

pivot screw.

Insert a pivot screw

through end of main bar

and into pivot plug...

PICK UP ICSA

Slip either pivot

plug into opening

on pivot bracket

and push pivot

screw ush

against bar.

Position ends of

main bar over

corresponding

pivot brackets.

Pick up the ICSA assembly holding the pivot

screws and pivot plugs in place with hands.

INSERT PIVOT PLUGS

Pivot

Bracket

Repeat on other side.

OMA18B P3

Extend canopy to expose

lower fabric screw.

Remove screw

with Phillips

screwdriver,

exposing fabric

grommet and

rivet nut.

Repeat on other side.

Arm Post

Red pull ring

should face out.

ATTACH RESTRAINT BELT AND ARMS

LOCATE FABRIC SCREW REMOVE FABRIC SCREW

Insert sharp screw through end of arm,

fabric grommet and into rivet nut.

Sharp screw should tighten ush

against arm.

SECURE ARM

Note:

If screw does

not turn easily,

unscrew and

start again.

POSITION ARM TRAY SIDE

POSITION ASSEMBLY

ASSEMBLE RESTRAINT BELT M AND ARM

Slide restraint belt M

grommet over arm post.

Position arm between

canopy and frame.

Align arm hole over

fabric grommet

and rivet nut.

Position arm between

canopy and frame.

Align arm hole over fabric grommet

and rivet nut.

OMA18B P4

90°

Slip nger under fabric and

plastic mount to hold nut in place.

Remove lower screw with

Phillips screwdriver.

PREPARE ASSEMBLY

Position both canopies

against handle bar.

REMOVE EXISTING FABRIC SCREW

Keeping your nger on the

nut, insert restraint belt

screw through hole

and into nut.

ATTACH RESTRAINT BELT F

Place restraint belt F

on stroller seat.

Note:

Save screw for right

side tray installation.

TIGHTEN SCREW

Tighten restraint belt

screw rmly with Phillips

screwdriver.

INSERT SHARP SCREW

Insert sharp screw

through arm, fabric

grommet and into rivet nut.

Hold strap at a 90

degree angle.

TIGHTEN SHARP SCREW

Tighten rmly with

Phillips screwdriver.

ATTACH RESTRAINT BELT F

Note:

If screw does not turn easily,

unscrew and start again.

OMA18B P5

PULL

PUSH

Fasten restraint belt over top

of infant car seat as shown.

FASTEN RESTRAINT

BELT

Britax®

Move car seat

handle into upright

carrying position.

RAISE HANDLE

INSTALL INFANT CAR SEAT

ENGAGE CAR SEAT

POSITION CANOPY

Position both canopies

against handle bar.

LOWER SEAT BACK

UNBUCKLE

RESTRAINT BELT

Unbuckle restraint

belt. Place ends

outside seat.

PREPARE STROLLER FOR INFANT CAR SEAT INSTALLATION

SET PARKING

BRAKE

Britax®Go To

Slide grooves on underside

of car seat onto ICSA

accessory bar.

POSITION

CAR SEAT

SET CAR SEAT

Gently pull canopy

stays while pushing

car seat handle.

Peg Pérego®Go To Graco®Go To

When installing car seat in the Duallie ICSA for the rst time,

test t with the car seat unoccupied to ensure you understand

the process. Installing occupied Infant Car Seat on Duallie ICSA

for rst time may result in accident, serious injury or death.

Place car seat

“rear facing” onto

ICSA accessory

bar, in a straight

downward

motion.

Warning

See the “Parking Brake”

section of your stroller

owner’s manual.

Lower seat back 7” to 8”.

See the “Reclining Seat”section

of your stroller owner’s manual.

Car seat should

“set” down onto

seat of stroller.

OMA18B P6

Fasten restraint belt over top

of infant car seat as shown.

FASTEN RESTRAINT BELT

Move car seat handle

into upright carrying

position.

POSITION HANDLE

Place car seat

“rear facing”

onto ICSA

accessory bar,

in a straight

downward

motion.

POSITION CAR SEAT

ENGAGE CAR SEAT

RAISE SEAT BACK

Peg Pérego®

Slide grooves on

underside of car seat onto

ICSA accessory bar.

TO REMOVE Britax®Go To

PULL

PUSH

SET CAR SEAT

Gently pull canopy stays while

pushing car seat handle.

Car seat should “set” down onto

seat of stroller.

Pull on red ring to tighten.

TIGHTEN RESTRAINT BELT

Be sure restraint belt tension

is not constricting child as it

may cause serious injury.

DOUBLE CHECK CAR SEAT IS

SECURELY ATTACHED

Warning

Pull car seat upward without

removing restraint belt.

You should not be able to

remove car seat without

unfastening restraint belt.

Warning

Failure to securely attach car seat

may result in serious injury or death.

See the “Reclining Seat”

section of your stroller

owner’s manual.

OMA18B P7

RAISE SEAT BACK REMOVE ACCESSORY BAR

Using a Phillips screwdriver,

remove both screws.

Move car seat handle into

upright carrying position.

POSITION HANDLE

TO REMOVE Peg Pérego®Go To

Graco®

POSITION CAR SEAT

Place car seat “rear facing”

onto ICSA main bar, in a

straight downward motion.

Be sure restraint

belt tension is not

constricting child as it

may cause serious injury.

Warning

Pull on red ring to tighten.

TIGHTEN RESTRAINT BELT DOUBLE CHECK CAR SEAT IS

SECURELY ATTACHED

Pull car seat upward without

removing restraint belt.

You should not be able to remove

car seat without unfastening

restraint belt.

Warning

Failure to securely attach car seat

may result in serious injury or death.

TIP: Attach screws to

accessory bar for future use.

CAUTION: Ends of accessory bar are sharp!

See the “Reclining Seat”

section of your stroller

owner’s manual.

OMA18B P8

ENGAGE CAR SEAT

Slide grooves on underside of

car seat onto ICSA main bar.

Fasten restraint belt over top of

infant car seat as shown.

FASTEN RESTRAINT BELT

Pull on red ring to tighten.

TIGHTEN RESTRAINT BELT

TO REMOVE Graco®Go To

UNFASTEN RESTRAINT BELT

Unfasten restraint belt.

Place ends outside seat.

With car seat handle

in upright position,

lift car seat straight

up and o ICSA bar.

Fasten restraint belt

when not in use.

SET PARKING BRAKE

FASTEN RESTRAINT BELT

Britax®

Peg Pérego®

Graco®

With car seat handle

in upright position,

squeeze red release

button under Graco®

car seat canopy, lift

car seat straight up

and o ICSA bar.

Red hook on Graco®

should be under

main bar.

Be sure restraint

belt tension is not

constricting child as it

may cause serious injury.

Warning

TO REMOVE CAR SEAT

Pull car seat upward without

removing restraint belt.

You should not be able to remove

car seat without unfastening

restraint belt.

DOUBLE CHECK CAR SEAT IS

SECURELY ATTACHED

Warning

Failure to securely attach car seat

may result in serious injury or death.

See the “Parking Brake”section of

your stroller owner’s manual.

OMA18B P9

TIP: Attach screws to

accessory bar for future use.

CAUTION: Ends of accessory bar are sharp!

REMOVE ACCESSORY BAR

RIGHT TRAY INSTALLATION

REMOVE LONG SCREWS

Using a Phillips screwdriver

remove both screws.

Using a Phillips

screwdriver, remove

3 long screws from

right tray.

ATTACH LONG SCREWS

Insert long screw through each hole in right tray,

main bar and into nut on underside of right tray.

Tighten rmly with Phillips screwdriver.

POSITION TRAY

Position right tray on main

bar, lining up holes.

Using a Phillips screwdriver and an 8 mm

socket wrench, remove short screw and nut.

REMOVE SHORT SCREW AND NUT

Reach under left tray and

press nut into hole.

Reach under right tray and insert

short screw through right tray,

left tray and into nut.

ATTACH SHORT SCREW AND NUT Tighten rmly with

Phillips screwdriver.

Children should not be

placed directly in the

BOB Stroller seat with the

Duallie ICSA installed,

unless tray is installed

directly in front of child for

safety and protection.

Warning

OMA18B P10

Inhaltsverzeichnis

Andere BOB Autositz Handbücher

BOB

BOB DUALLIE Einrichtungshandbuch

Beliebte Autositz Handbücher anderer Marken

Britax

Britax PARKWAY SGL Bedienungsanleitung

JANE

JANE nurse cruiser Bedienungsanleitung

Digicom

Digicom Tippy Pad Bedienungsanleitung

Giordani

Giordani orion 012 Bedienungsanleitung

BRIO

BRIO ZENTO Bedienungsanleitung

Combi

Combi Zeus Turn 8815 Series Bedienungsanleitung

Graco

Graco Car Booster Seat Bedienungsanleitung

Coccolle

Coccolle Atira Bedienungsanleitung

hifold

hifold HF01-GL Bedienungsanleitung

CYBEX

CYBEX SOLUTION X2-FIX Bedienungsanleitung

kiwy

kiwy SLF 123 Bedienungsanleitung

Safety 1st

Safety 1st Summit ISO 30 Bedienungsanleitung

Safety 1st

Safety 1st Grand 2-IN-1 Bedienungsanleitung

Graco

Graco NAUTILUS Bedienungsanleitung

Britax

Britax Multi-Tech BB0-702-00 Bedienungsanleitung

Grammer

Grammer MSG45/421 Betriebsanleitung

Nuna

Nuna REBL PLUS Bedienungsanleitung

Graco

Graco Child Restraint Bedienungsanleitung