Bogen BOMDMU Bedienungsanleitung

50 Spring Street, Ramsey NJ 07446, USA

Te: 201-934-8500; Fax: 201-934-9832; www.bogen.com

BOMDMU

Messaging and Call Stacking System

User's Manual

54-2213-01A 1208

General Safety Instructions

Always follow these basic safety precautions when using the system:

1. Read carefully and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. DO NOT block or cover ventilation slots and openings.

4. DO NOT place the product in a closed enclosure or cabinet unless proper

ventilation is provided.

5. Never spill liquid on the product or drop objects into the ventilation slots and

openings. Doing so may result in serious damage to the components.

6. Repair or service must be performed by a factory authorized repair facility.

7. A UL/CSA approved power pack is provided.

8. DO NOT staple or otherwise attach the power supply cord to building surface.

9. DO NOT use the product near or in wet or damp places, such as wet basements.

10. DO NOT use extension cords. Install within six feet of a grounded outlet

receptacle.

11. DO NOT install during lightning storm.

12. Never touch un-insulated wires or terminals unless the unit is disconnected from

both power and the rest of the phone system.

13. Use Caution when installing or modifying configuration switches or control lines.

14. The unit must be securely attached to a wall board, rack or table mounted.

CAUTION: If any wiring from the system leaves the premises,

you must use proper electrical protectors.

Regulations:

FCC (Part 15) Radio Frequency Interference

The BOMDMU generates and uses radio frequency energy and if not installed and

used in strict accordance with the manufacturer's instructions, may cause interference

to radio and television reception. Unit complies with the limits for Class A devices in

accordance with the specifications in Subpart J of Part 15 of the FCC Rules. This

testing is designed to provide reasonable protection against such interference.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause interference to radio or television reception,

which can be determined by turning the unit off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

Reorient the radio or TV receiving antenna.

Relocate the unit with respect to the radio or TV receiver or vice-versa.

Plug the unit into a different outlet so that it and the radio or TV receiver are

on different branch circuits

If necessary, the user should consult the dealer or an experienced

radio/television technician for additional suggestions.

Limited Warranty; Exclusion of Certain Damages

The BOMDMU Messaging and Call Stacking System is warranted to be free

from defects in material and workmanship for one (1) year from the date of sale to

the original purchaser. Any part of any Bogen product covered by this warranty

that, with normal installation and use, becomes defective (as confirmed by Bogen

upon inspection) during the applicable warranty period, will be repaired or

replaced by Bogen, at Bogen’s option, provided the product is shipped insured

and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey,

NJ 07446, USA. Repaired or replacement product will be returned to you freight

prepaid. This warranty does not extend to any of our products that have been

subjected to abuse, misuse, improper storage, neglect, accident, improper

installation or have been modified or repaired or altered in any manner

whatsoever, or where the serial number or date code has been removed or

defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE

WARRANTY AND THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS

OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND

EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's

liability arising out of the manufacture, sale or supplying of products or their use or

disposition, whether based upon warranty, contract, tort or otherwise, shall be

limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE

FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING,

BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF

USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR

SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the

exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you. This warranty gives you specific legal

rights, and you may also have other rights which vary from State to State.

Products that are out of warranty will also be repaired by the Bogen Factory

Service Department -- same address as above or call 201-934-8500. The parts

and labor involved in these repairs are warranted for 90 days when repaired by

the Bogen Factory Service Department. All shipping charges in addition to parts

and labor charges will be at the owner's expense. All returns require a Return

Authorization number. For most efficient warranty or repair service, please include

a description of the failure.

Products manufactured and labeled by other companies may be covered by

warranties offered by such companies. Please call Bogen Customer Service or

refer to product packaging for manufacturer’s warranty for non-Bogen branded

products.

12/2008

NOTES

____________________________________________________________________

Table of Contents

1. OVERVIEW ........................................................................................ 2

1.1 Features and Capabilities................................................................ 2

1.2 General Specifications .................................................................... 3

2. INSTALLATION & CONFIGURATION ..................................................... 4

2.1 Installation Steps ............................................................................. 4

2.2 Hardware Description...................................................................... 4

2.2.1 Status LED Indicators...................................................... 5

2.2.2 Power Input ..................................................................... 6

2.2.3 Audio/Control Inputs, Paging Channels 1-3 .................... 6

2.2.4 Port Configuration Switch, Channels 1-3, PRI, MSG ...... 6

2.2.5 Priority Audio/Control Input ............................................. 7

2.2.6 Priority Mode Switch........................................................ 7

2.2.7 Messaging Audio/Control Input ....................................... 7

2.2.8 Messaging Mode Switch…………………………………….7

2.2.9 Background Music Input Volume..................................... 7

2.2.10 Background Music Input Connector ................................ 8

2.2.11 Audio Output Mode Switch.............................................. 8

2.2.12 Output Volume ................................................................ 8

2.2.13 System Audio/Control Connector .................................... 8

2.2.14 Configuration Switches.................................................... 9

2.2.15 Messaging Playback Auxiliary Interface .......................... 13

2.2.16 Paging Control and Status Auxiliary Interface ................. 13

3. PAGE STACKING, FEEDBACK ELIMINATION OPERATION................. 14

3.1 Page Recording............................................................................... 15

3.2 Record Activation Methods ............................................................. 15

3.3 Playback ........................................................................................ 15

4. QUEUE ........................................................................................ 16

5. PRIORITY ........................................................................................ 16

6. MESSAGING, PRE-RECORDED............................................................. 16

7. BACKGROUND MUSIC INPUT ............................................................... 17

8. AUDIO OUTPUT ...................................................................................... 17

9. LIMITED WARRANTY; Exclusion of Certain Damages............................ 21

Shipping Container Contents

The following items should be found in the container of BOMDMU:

▪BOMDMU System

▪Installation and User Guide

▪Mounting screws

▪Wall mounted power pack, 12V DC @ 1 Amp

1. OVERVIEW

1.1 Features and Capabilities

The BOMDMU is a comprehensive system that combines Page Stacking,

Feedback Elimination, Pre-Recorded Messaging and Background Music

control into a single device.

PAGE STACKING/FEEDBACK ELIMINATION: For busy overhead paging

systems, the BOMDMU offers 3 channels of page stacking and feedback

elimination. Each channel can record and temporarily store up to 16 pages

or 4 minutes of audio. Page input channels can record simultaneously, and

while the system is playing.

PRIORITY PAGING: For emergencies, the BOMDMU offers a priority input

that overrides the stacking and messaging functions and provides

immediate, real-time access to the paging system.

PRE-RECORDED MESSAGES: For security and general public address

messaging, a pre-recorded messaging sub-system has been included.

Access both Record and Play functions of up to 99 messages/8 minutes of

audio from an extension on your host telephone system. Ten (10) start

contacts have also been provided to trigger messages from external devices

such as sensors or alarm systems.

BACKGROUND MUSIC: To keep everything in harmony, the BOMDMU also

includes a background music input. This allows playback of your favorite

music source over the paging system. When a page or message is played,

the background music will be muted and the announcement will be heard

loud and clear.

BOMDMU Connection to Override to UTI312

Appendix

BOMDMU Connection to Override to PCMTIM

BOMDMU Connection to Override to UTI1

1.2 General Specifications

AUDIO

Bandwidth 100 Hz to 8 kHz

Page Input 3, RJ12 connector, Station Port/Dry Loop/Loop Start

Priority Input 1, RJ12 connector, Station Port/Dry Loop/Loop Start

Messaging Input 1, RJ12 connector, Station Port/Dry Loop/Loop Start

Background Music

Input

Line level input with level control

Page output 1, RJ12 connector, 8-ohm power/600-ohm line level

(switch-selectable), adjustable

PAGE STACKING

Message repeat play one or two times, DIP switch selectable

Delay between

messages

1s, 3s, 5s, 10s DIP selectable

Stack up to 16 messages per input

DTMF Store/forward (0,2,3 or 4 tones) DIP selectable

Pre-Page Tone DIP selectable

POWER

Power Pack 12V DC @ 1 Amp, UL and CSA

MEMORY

Type FLASH

Page Stacking 4 minutes per page input channel

Messaging 8 minutes

MESSAGE CONTROL

# of messages 99

Record Control DTMF control from messaging input

Play Control Triggered from DTMF on messaging input or start

contacts (10)

PAGE CONTROL

Priority Control contact is offered on the Priority Input RJ12

connector

Page Inputs 3, Page Input RJ12 connector. Each input answers

(loop, audio sense, DTMF)

STATUS OUTPUTS Solid State Relay contacts 24V DC @ 100 mA max.

Playing Contact Offered on the Page Output RJ12 connector

Record Contact Offered on each Page Input RJ12, as well as the

Message Input RJ12

PACKAGE

Chassis: Rack mount (1 RU)

Material: 18 gauge cold rolled steel, painted with silkscreen

18 3

2. INSTALLATION & CONFIGURATION

This section provides complete instructions for mounting the BOMDMU in a rack

or on a table. It also illustrates all interface requirements to auxiliary equipment,

including inputs and outputs. Configuration switch settings are provided.

2.1 Installation Steps

These are the general steps for installation:

1. Find a space in a rack or on a table. Mount the unit to the selected place

with its wiring at least 18” away from the power supply or other equipment

that generates electrical noise. Secure unit using the supplied mounting

screws.

2. Make sure there is a standard electrical outlet into which you can plug the

power pack. This outlet should NOT be controlled by a wall switch.

3. Make cable connections from the BOMDMU to the PBX or audio source

and the Paging system,

4. Set DIP switches to the desired operation.

5. Connect the power supply. System OK LED should illuminate GREEN.

6. Test unit operation.

2.2 Hardware Description

FRONT

The BOMDMU is a standard 1RU 19” rack mount chassis.

The front panel of the BOMDMU provides user indications of the system

status via LEDs. The description of each LED can be found in section 2.2.1

of this manual.

Configuration switches are also accessible on the front panel of the unit.

The description of the various user configurable settings can be found in

section 2.2.14 of this manual.

7. BACKGROUND MUSIC INPUT

The BOMDMU allows for a background music source to be mixed with pages

and pre-recorded messages. Background music is muted when pages or pre-

recorded messages are played to the audio output. The BGM Level control

allows you to optimize the level music sent to the audio output.

8. AUDIO OUTPUT

The audio output of the BOMDMU is the audio interface for your zone controller,

amplifier or public address system. All audio from the paging channels, priority

input, messaging system and BGM input is routed to this output. The BOMDMU

manages stored pages on a first in, first out basis. This means that pages will be

played in the order they were successfully completed and or triggered,

independent of the particular input. Only the priority input has the ability to

interrupt the playback queue. In the case of a priority page, the system will pause

the playback queue during the priority page, then continue when the page is

complete.

4 17

4. QUEUE

The BOMDMU incorporates a playback queue to manage the order that

messages play. This queue will manage up to 32 pages. Pages are put into the

queue on a first in, first out basis. The queue is compatible with pages from any

of the three page channels and/or the messaging input. The priority input offers

live, or direct, access to the output of the system. A priority page will pause the

playback queue. When the priority session completes, the queue will continue

from where it left off.

5. PRIORITY

The BOMDMU offers a Priority input to gain immediate access to the public

address system. Activation of priority halts the playback of recorded pages.

When the priority page is completed, the BOMDMU will resume playback from

the beginning of the message that was interrupted. Priority Activation methods

include Analog Station, Dry Loop and Loop Start. A valid connection via any of

these methods provides direct access to the system. Status of the Record

Activation switches is not relevant.

6. MESSAGING, PRE-RECORDED

The BOMDMU offers a pre-recorded messaging system for quick and easy

access to standard or frequently used pages. This system allows messages to be

recorded and permanently stored in FLASH memory. Playback is provided via

DTMF command or contact closure. The messaging portion of the BOMDMU can

store up to 99 messages in 8 minutes of memory.

DTMF Commands

Code Name Description

# End Use this function to stop recording or exit a

command

*0 Stop Stop playing all triggered messages

*3xx Delete Delete message at location xx

*5xx -or- xx Play Play message at location xx to the audio output

*6xx Review Listen to a message through the handset. Audio is

NOT routed to the audio output

*7xx Record Record message into location xx. Recordings may

only be made to empty message locations. To

update a previously recorded message, make sure

to delete it first.

Connect to the messaging system with the desired mode, analog station, dry

loop or loop start. The Message Off Hook LED indicates that you are connected

to the system in Loop Start or Analog Station mode.

A steady tone indicates a correctly executed and accepted command. A fast

busy signal indicates an incorrectly executed command.

BACK

The back panel of the BOMDMU provides all electrical connections to the

device. The connector type and signal descriptions are detailed later in this

manual.

Individual configuration of each audio input / output port is provided next to

each audio input connector.

Volume controls are provided for the BGM input and the audio output.

Flanges are provided on each side of the back panel of the BOMDMU to

provide strain relief to all the wiring routed to the BOMDMU.

2.2.1 Status LED Indicators

All Status Indicators are located on the front panel of the unit. The

different groups of LED indicators are described below:

2.2.1.1 System

The System indicators are global indicators that indicate that a particular

function is active on any, or all, of the inputs on the system.

System OK LED – Green, indicates unit is ON. Flashing indicates an

error condition, contact the factory for more information should this

occur.

Recording LED - Red, indicates that a recording session is active on

any one of the paging inputs.

Playing LED - Green, indicates that the audio output of the BOMDMU

is active due to a page playing back, or the priority input being active.

Busy LED - Yellow, indicates that any one of the paging inputs is

recording, playing, or in a delay mode. This LED is also active when

a priority announcement is being made.

2.2.1.2 Message Input

Messaging Input Off Hook LED - Yellow, indicates the messaging

system is being accessed via a phone circuit. (Loop current flowing)

Messaging Input Level LED - Yellow, indicates audio signal is present

on the Message Input.

16 5

2.2.1.3 Priority Onput

Priority Input Off-Hook LED - Yellow, indicates the priority channel is

being accessed via a phone circuit. (Loop current flowing)

Priority Input Active LED - Yellow, indicates the priority channel is

active.

2.2.1.4 Paging Input Channels (Channels 1,2,3)

Off-Hook LED - Yellow, indicates the priority channel is being accessed

via a phone circuit. (Loop current flowing)

Audio Sense LED - Yellow, indicates audio signal is present on that

particular Page port.

Record LED - Red, indicates that the particular Paging channel is

recording a message.

Play LED - Green, indicates that the particular Paging channel is

playing a message.

2.2.2 Power Input

Unit requires 12 VDC @ 1 Amp via the barrel connector. Only use the

factory supplied power pack. The chassis is connected to the negative

side of power supply.

2.2.3 Audio/Control Input, Paging Channels 1 - 3

RJ12 style connector, 6 position. All pages to be recorded are input to

the device through these connectors.

1. Abort, stops and deletes the recording when

connected to Ground (Pin 5).

2. Record input, connect to Ground(Pin 5) to

activate. Unit records for duration of closure.

3. Audio, ring/return.

4. Audio, tip/signal.

5. System Ground, (power return).

6. Not used.

2.2.4 Port Configuration Switch, Paging Channels 1 – 3, Priority

Input, Message Input

A three-position slide switch is provided for each of the five inputs from

the paging system: Channel 1, 2, 3, Priority, and Message. The switch

configures the particular port to meet the requirements of the paging

system.

Analog Station - LEFT Position. Impedance 900-ohm, voltage for ring

trip 75 to 105V (20 to 60Hz).

Dry Loop - Center Position. Configures audio input for 600-ohm, line

level (-10 dB nominal).

Loop Start - RIGHT Position. Configures priority audio input for 900-

ohm and supplies 24V DC talk battery. Compatible with loop start trunk

ports.

3.1 Page Recording

Upon receiving a valid recording signal, the BOMDMU will start recording at

the beginning of the memory until the page is complete. While this page is

playing, new pages can still be recorded. Multiple pages will be recorded in

series until the playing message has completed its play routine.

Multiple channels may be recording incoming pages at the same time.

Playback order of pages is based on when the recording process is

complete. For example, if a long message is being recorded on channel 1,

and during that process a short message is recorded and completed on

channel 2, the playback order will be the message on channel 2 then the

message on channel 1.

3.2 Record Activation Methods

There are several methods to initiate automatic record mode on the

BOMDMU. The activation mode will be selected by the Setup Switches upon

power up. It cannot be changed during normal operation.

Loop Current detect - Setup Switches 1=OFF, 2=OFF

If an input’s input configuration switch is set for loop start mode, the

BOMDMU will source the talk battery (24V DC) to the ring and tip, and then

sense the loop current when phone goes off hook and start the recording

process for the duration of the page. Valid for Analog Station and Loop Start

modes.

Audio Sense - Setup Switches 1=OFF, 2=ON

For record activation without a separate switch closure or loop current. The

BOMDMU will start recording when the audio sensor goes active and will

stop when the audio sensor is inactive for three seconds. Valid for Analog

Station, Loop Start and Dry Loop modes.

DTMF Activation - Setup Switches 1=ON, 2=OFF

For record activation without a separate switch closure and perhaps noisy

audio lines. The BOMDMU will start recording when it “sees” a valid DTMF

tone and will stop when the audio sensor is inactive for three seconds. Valid

for Analog Station and Loop Start modes. The DTMF tone used to activate

the recording will be stripped and not output when the message is played.

Manual Recording - Available in all modes. Typically associated with Dry

Loop mode, this enables the BOMDMU to begin recording with a switch

closure between pins 2 and 5 of the RJ12 connector of a particular channel.

3.3 Playback

The BOMDMU can be configured to automatically playback pages after their

record process has completed. This mode is configured by setting Setup

Switch 8 to OFF.

The BOMDMU may be configured for manual or switch closure playback

(Setup Switch 8=ON) when you want full control of when pages will

playback. Playback is triggered via a momentary closure (100ms) between

pins 1 and 5 of the Paging Control and Status Auxiliary Interface.

6 15

6 Not Used Not Used

7 Busy Common Common for the busy relay

8 Busy Relay Activates when system is recording or

playing a message.

9 Playing Common Common for the Playing Relay.

10 Playing Relay Activates when system is playing.

11 Recording Common Common for the Recording Relay.

12 Recording Relay Activates when the system is

recording.

3. PAGE STACKING, FEEDBACK ELIMINATION OPERATION

The BOMDMU offers 3 channels of page stacking, intended for busy paging

systems with multiple inputs. Each channel performs the following functions:

1. It eliminates feedback by recording the incoming page(s), then playing them

back after the user “hangs up”, eliminating any feedback loop.

2. It is able to repeat each page allowing for better intelligibility in a noisy

environment.

3. It is capable of stacking up to 16 incoming pages per channel by recording

incoming pages while playing back previously recorded ones on a first-in first-

out basis.

Constraints:

Each page is allowed a maximum of 1 minute recording time. Pages

exceeding this will be aborted and a busy back tone is generated.

Recordings that reach the end of memory are considered incomplete.

These pages are aborted and a busy back tone is generated. If the

memory is filled and a new recording command is offered, the

BOMDMU will not go into record mode and a busy back tone will be

output to tell the user that the system is not available.

The recorded message must be a minimum of one second in length.

Any message shorter than this will be aborted.

The BOMDMU aborts pages that are comprised of 3 or more seconds of

silence. The page is deleted and a busy back tone is generated.

Other important features include the ability to Record/Regenerate, or Block

DTMF tones for use in zone controller applications.

The BOMDMU is designed to run in both Automatic and Manual modes. For

paging applications the Automatic mode is the most widely used. This mode

requires minimum installation time since it is the factory’s default setup. RJ12

connectors are used for Audio inputs and outputs. Where logical, certain control

signals are also provided on the individual RJ12 connectors associated with each

input.

2.2.5 Priority Audio/Control Input

RJ12 style connector, 6 position. Priority pages are input to the device

through this connector.

1. Not used.

2. PRIORITY input, connect to Ground (Pin 5) to

activate. Priority active for duration of closure.

3. PRIORITY Audio, ring/return.

4. PRIORITY Audio, tip/signal.

5. Ground. (power return).

6. Not used.

2.2.6 Priority Mode Switch

Analog Station – LEFT Position. Impedance: 900-ohm, voltage for ring

trip 75 to 105V (20 to 60 Hz).

Dry Loop – CENTER Position. Configures audio input for 600-ohm,

line-level (-10 dB nominal).

Loop Start – RIGHT Position. Configures priority audio input for 900-

ohm and supplies 24V DC talk battery. Compatible with loop start trunk

ports.

2.2.7 Messaging Audio/Control Input

Input, RJ12 style connector, 6 position. Operation of the messaging

portion of the system is provided through this interface.

1. Not used.

2. Not used.

3. Audio, ring/return.

4. Audio, tip/signal.

5. Not used.

6. Not used.

2.2.8 Messaging Mode Switch

Analog Station – LEFT Position. Impedance: 900-ohm, voltage for ring

trip 75 to 105V (20 to 60 Hz).

Dry Loop – CENTER Position. Configures audio input for 600-ohm,

line-level (-10 dB nominal).

Loop Start – RIGHT Position. Configures priority audio input for 900-

ohm and supplies 24V DC talk battery. Compatible with loop start trunk

ports.

2.2.9 Background Music Input Volume

Controls the background music input volume level delivered to the audio

output. Adjusting this input clockwise increases the level, and counter-

clockwise rotation decreases the level of the background music.

14 7

2.2.10 Background Music Input Connector

RCA jack, Input audio level should be set to a nominal level of 0dBv, or

less. Tip is audio signal and sleeve is audio return.

Any audio input at this port will be fed through the system to the audio

output whenever the system is idle.

2.2.11 Audio Output Mode Switch

A two position slide switch allows the user to configure the audio output

to match the needs of their downstream equipment.

The RIGHT position sets the output to line level (+4 dB / 600-ohm). Use

this position as default.

The LEFT position sets the output to power level (500 mW / 8-ohm).

Use this for longer runs, or if not enough level can be reached with the

line level output.

2.2.12 Output Volume

Controls the audio output volume level delivered to the paging system. It

is shipped with 1:1 gain factory set.

Adjusting this input clockwise increases the level, and counter-clockwise

rotation decreases the level of the device

2.2.13 System Audio/Control Connector

Output, RJ12 style connector, 6 position. All audio from the BOMDMU

is output through this port

1. Not used.

2. Playing Relay, Normally Open.

3. Audio Return.

4. Audio Signal.

5. Playing Relay, Common.

6. Not used.

The playing relay contacts available on this connector are paralleled

with the connections on the Paging Control and Status Auxiliary

Interface, positions 9 and 10.

11 12

*1 second

3 seconds

5 seconds

Delay Between Plays

To make the page sequence more intelligible,

a pause can be inserted between each

message in the playback sequence as well as

between any repeats of each message.

10 seconds

2.2.15 Messaging Playback Auxiliary Interface

Top row of 12 inputs on the Auxiliary Interface. This interface allows

playback of pre-recorded messages through a momentary closure

(100ms). Each closure between a Play input and Ground will play the

corresponding message one time. Multiple closures on a single input or

several inputs will queue the messages and the system will play them in

the order received.

12 position Euro-style, two piece, pluggable type.

Pin Name Description

1 Ground Common

2 Play 1 Plays message 1 when connected to ground

3 Play 2 Plays message 2 when connected to ground

4 Play 3 Plays message 3 when connected to ground

5 Play 4 Plays message 4 when connected to ground

6 Play 5 Plays message 5 when connected to ground

7 Play 6 Plays message 6 when connected to ground

8 Play 7 Plays message 7 when connected to ground

9 Play 8 Plays message 8 when connected to ground

10 Play 9 Plays message 9 when connected to ground

11 Play 10 Plays message 10 when connected to ground

12 Not Used Not Used

2.2.16 Paging Control and Status Auxiliary Interface

Bottom row of 12 inputs on the Auxiliary Interface. Allows manual

access to many of the common inputs and status outputs of the system.

12 position Euro-style, two piece, pluggable type.

Pin Name Description

1 Ground Common

2 Not Used Not Used

3 Priority Initiates priority page when connected

to ground.

4 Stop Stops any currently playing message

when connected to ground.

5 Play Plays next message in queue when

connected to ground.

8 13

Inhaltsverzeichnis

Andere Bogen Konferenzsystem Handbücher

Bogen

Bogen Nyquist C4000 Series Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung