Bogen HFCS1 Leitfaden

Specifications subject to change without notice.

54-2091-01A 0302 Printed in Taiwan.

High-Fidelity

Ceiling Speaker

HFCS1

Installation and Use Manual

Product Diagrams

HFCS1Front Drawing (grille removed)

1. Coaxial Driver Assembly

2. Dual Bass Tuning Vents (x2)

3. Grille Retention Groove

4. Power Tap Selection Switch

5. Mounting Clamp Screws (x4)

HFCS1Rear Drawing

6. Metal Back Can

7. Snap-Lock Input Connector

8. Mounting Clamps (x4)

HFCS1Rear Drawing (terminal cover)

9.Terminal Covers (2 identical halves)

10. Eyelets (x2)

11. Mounting Screws (x4)

12.Wire Exit Slot

13. Conduit Knock Out (x2)

HFCS1Front Drawing

(grille removed)

HFCS1Rear Drawing

(terminal cover)

Installation

The HFCS1can be installed in a variety of ceiling environments.The use of theTBCR

(Tile Bridge Support Ring) accessory may be desired for many of these environ-

ments.

For suspended ceilings, the use of a TBCR is strongly recommended to

help support and distribute the weight of the speaker.

In new construction situations, the TBCR, installed before sheetrock, acts as a rout-

ing template that ensures an accurate and neat hole for installation. The TBCR can

also be used as a support ring in retrofit applications to better distribute the speak-

er’s clamping forces. (See Accessory section on page 4.)

1. Begin by cutting a 10-¾" circular hole where the HFCS1will be installed. If using

a TBCR, then follow its installation instructions for the specific type of environ-

ment the HFCS1is being installed in.

2. Remove the speaker’s grille using a sharp tool to pry the grille out of its groove.

3. Make electrical connections to the pluggable terminal strip and plug it onto the

HFCS1. See section on Speaker Wiring on page 3.

4. Install terminal cover plates, if necessary or desired, using 4 screws. See the sec-

tion on Terminal Covers options on page 3 if using conduit or if it is required to

secure the speaker directly to the structure (typically for suspended ceilings).

5. Position the swing-out clamps so that they are against the body of the speaker

and insert the speaker into its opening in the ceiling.

6. Tighten the clamps by turning the clamping screws clockwise. Do not over-tight-

en the clamps - only tighten until the speaker is fairly snug in the mounting hole.

If using an electric driver, set the clutch to the lowest setting.

Do not replace the grille until the power level is set via the rotary selector switch

on the front panel. Refer to the Selecting Power Levels section on page 4 for instruc-

tions on selecting the power level.

IMPORTANT

• There must be a minimum of 11" of vertical clearance between the FRONT

of the mounting surface and any other structure for the speaker to fit. Before

cutting the full hole, use a smaller exploratory hole to determine if there are

any obstructions.

• The edge of the hole must be a minimum of 1-¼" away from any side obstruc-

tions to ensure that they will not interfere with the action of the clamps.

Speaker Wiring

Wiring is terminated at a snap-lock input con-

nector. There are two positive and two nega-

tive terminals to accommodate daisy chaining

of speakers in a system. All wiring should be

done prior to installation and then plugged

into the rear of the HFCS1.

DAISY CHAINING

The HFCS1’s snap-lock input connector

allows for easy daisy chaining of speakers by

providing a second terminal of each polarity.

See the figures to the right and below for cor-

rect wiring for daisy chaining of terminals.

SPEAKER PHASING

Keep the same polarity terminals wired together to ensure correct phasing. In order

to provide the best possible sound, all of the speakers in a system need to be push-

ing out and pulling in at the same time.

If the connections to one speaker in a system are reversed from the others, that

speaker’s movement will be out of sync with the other speakers.This will result in a

loss of low frequency response and will effect the overall performance of the sys-

tem.

TERMINAL COVERS

• The two terminal cover halves are attached to the back of the speaker using 4

screws. It is important that all 4 screws be used to mount the covers.

• A slot between the two halves allows the wire to exit the speaker while pro-

tecting the connections. The cover's eyelets can be used to anchor the wire

using a wire tie if desired.

• If local codes require the use of a conduit for connections or strain relief of the

connections, a knock out can be removed and a proper fitting installed for the

particular situation.

• Eyelets are provided on the terminal covers to provide a means of securing the

speaker to the structure when necessary. It is important that all 4 terminal cover

attaching screws be installed in this application.

Selecting Power Levels

The front-mounted selector switch is used to

set the appropriate power level or impedance

for your system. Using a small, flat-blade screw-

driver, turn the knob until the slot points to the

power level you require.

70V/100V SYSTEMS

Both power setting scales for 70V and 100V sys-

tems are labeled on the speakers. On the 100V

scale, the last position clockwise is marked with

a symbol. Do not use this position in 100V

systems.

ΩΩ

SYSTEMS

The fully counterclockwise position of the setting switch is the 16-ohm position.This

setting is suitable for use with low-impedance amplifiers that tyically support 4- or

8-ohm speakers.The speaker’s higher, 16-ohm impedance makes it easier to combine

multiple speakers into series - parallel networks while keeping the total system

impedance at a level suitable for low-impedance amplifiers.

25V SYSTEMS

The HFCS1will operate on 25V systems, but at

reduced power levels. The chart to the right

shows the conversion from a 70V power setting

to the actual 25V power level.

Accessory

TBCR (TILE BRIDGE SUPPORT RING)

The TBCR is a combination tile bridge and

support ring that assists in securing the

HFCS1and in distributing the weight of the

HFCS1in various types of installations.

25V Conversion Table

70V Setting

32W 4W

25V Power

16W 2W

8W 1W

4W 1/2W

2W 1/4W

1W1/8W

16Ω39W

Specifications

SPECIFICATIONS HFCS1

Frequency Response (-10 dB)*65 Hz to 19 kHz

LF Driver 6-1/2" PolyCone

HF Driver 20 mm (3/4") Polycarbonate Dome

Sensitivity (1W/1M)89 dBspl (Average 100 Hz - 10 kHz)

Impedance Ratings Low (16 ohms) / High (70V/100V)

Power Input (Max.) 75W @ 16 ohms; 32W @ 70V/100V

Power Settings (in watts)†70V: 32, 16, 8, 4, 2, 1& 16 ohms

100V: 32, 16, 8, 4, 2 & 16 ohms

Baffle Material Fire-rated (94VO) ABS

Back Can Material Heavy-Gauge Plated Steel

Terminations 4 Terminal Snap-Lock Input Connector

Product Weight 9 lb.

Speaker Dimensions 12-5/16" dia. x 12" D

Vertical Clearance

Requirement Minimum 11" (From Mounting Surface Front)

Included Accessories Input Terminal Cover (2 Halves); (4) Screws;

(1) Snap-Lock Input Connector

Optional Accessories Tile Bridge Support Ring (TBCR)

Baffle Ring Finish & Color Textured White

*Half-Space Response, 16-ohm input

† Front panel, switch-selected.

50 Spring Street, Ramsey, NJ 07446, U.S.A.

Tel. 201-934-8500, Fax: 201-934-9832, www.bogen.com

Bogen HFCS1Ceiling Speakers are warranted to be free from defects in material or

workmanship provided that the product has not been subjected to abuse or accident

or altered in any way for three (3) years from the date of sale to the original purchas-

er. Any part of the product covered by this warranty that, with normal installation and

use, becomes defective will be repaired or replaced by Bogen, at our option, provided

the product is shipped insured and prepaid to: Bogen Factory Service Department, 50

Spring Street, Ramsey, NJ 07446, USA.The product will be returned to you freight pre-

paid.This warranty does not extend to any of our products that have been subjected

to misuse, improper storage, neglect, accident, improper installation or have been mod-

ified or repaired in any manner that Bogen believes may affect the reliability of the

product, or where the serial number or date code has been removed or defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND

EXCLUSIVE WARRANTY AND THE PURCHASER’S SOLE AND EXCLU-

SIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY

KIND, EITHER EXPRESS OR IMPLIED,AND ALL IMPLIED WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

ARE HEREBY DISCLAIMED AND EXCLUDED. Bogen's liability arising out of

the manufacture, sale or supplying of products or their use or disposition, whether

based upon warranty, contract, tort or otherwise, shall be limited to the price of the

product. In no event shall Bogen be liable for special, incidental or consequential dam-

ages (including, but not limited to, loss of profits, loss of data or loss of use damages)

arising out of the manufacture, sale or supplying of products, even if Bogen has been

advised of the possibility of such damages or losses.

Products that are out of warranty will also be repaired by the Bogen Factory Service

Department -- same address as above or call 201-934-8500. The parts and labor

involved in these repairs are warranted for 90 days when repaired by the Bogen

Factory Service Department. All shipping charges in addition to parts and labor

charges will be at the owner's expense.

Warranty

Inhaltsverzeichnis

Andere Bogen Sprecher Handbücher

Bogen

Bogen SPT-5A Bedienungsanleitung

Bogen

Bogen SP158A Bedienungsanleitung

Bogen

Bogen SP158A Bedienungsanleitung

Bogen

Bogen 700286198 Leitfaden

Bogen

Bogen NEAR IG Series Bedienungsanleitung

Bogen

Bogen Easy Design HS30EZ Bedienungsanleitung

Bogen

Bogen MB8TSL Bedienungsanleitung

Bogen

Bogen MPS1B Leitfaden

Bogen

Bogen HFCS1 Leitfaden

Bogen

Bogen 14018 Bedienungsanleitung

Bogen

Bogen FG20B Bedienungsanleitung

Bogen

Bogen Nyquist NQ-S1810CT-T1 Betriebsanleitung

Bogen

Bogen BDT30A Bedienungsanleitung

Bogen

Bogen KFLDS30T Bedienungsanleitung

Bogen

Bogen IH8A Bedienungsanleitung

Bogen

Bogen Easy Design CS1EZ Bedienungsanleitung

Bogen

Bogen FMH15T Bedienungsanleitung

Bogen

Bogen G8G Bedienungsanleitung

Bogen

Bogen ENHANCER ESYS1 Bedienungsanleitung

Bogen

Bogen AMT-12 Dimensionsleitfaden

Bogen

Bogen AMBSL1 Bedienungsanleitung

Bogen

Bogen Quantum WBS810QIP Bedienungsanleitung

Bogen

Bogen HFCS1LP Leitfaden

Bogen

Bogen CSD1X2VR Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung