Bond GRAND BLOOMINGTON FOUNTAIN Bedienungsanleitung

GRAND BLOOMINGTON FOUNTAIN

ITEM # Y95871

Serial Number Purchase Date

Questions, problems, missing parts?

Before returning to your retailer, call our customer service department at 1-866-771-

BOND (2663) 8 a.m. – 4:30 p.m. PST, Monday – Friday.

ATTACH YOUR RECEIPT HERE

SAFETY INFORMATION

WARNING

Please read and understand this entire manual before attempting to assemble, operate or install the

product.

• Save these warnings and instructions for reference. Read all instructions before use.

• Failure to follow warnings and instructions may result in injury or property damage.

• Excessive weight or pressure on any of the fountain sections may cause it to fall. Keep pets,

children, or anyone from sitting, leaning, or climbing on any of the fountain components.

• While fountain is designed to operate as splash free as possible, some water splashing out of

the fountain is inevitable. Place the fountain in a location where any splashing will not cause

damage.

• The National Electric Code requires that a ground fault circuit interrupter (GFCI) be used in the

branch circuit supplying fountain pump and other pond equipment. Seek your electrical supplies

dealer for this device.

• Always keep the fountain working with sufficient water and clean of debris and dirt to ensure proper

functioning of the pump.

• If necessary, clean the fountain with a soft cloth and change the water frequently. Due to water

evaporation, you may see a buildup of white residue on the fountain surface from mineral content in

the water supply. To prevent such buildup, regularly clean the fountain with soap and water. Do not

use any abrasive, which may damage the applied finish.

• Use of water clarifier or algaecide of any kind will damage the paint in the fountain and will not be

covered under the manufacturer’s warranty.

• This fountain is intended for outdoor use only.

• See the pump instructions for pump safety, maintenance, and warranty information.

• The pump on your fountain has no user-serviceable parts. Only an authorized service

representative should service the pump.

•

California Prop. 65 Warning: This product can expose you to the chemicals including Lead

and Lead Compounds, which are know to the state of California to cause cancer and birth

defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

CAUTION

SAFETY INFORMATION

1. Install the fountain pump correctly before operating it.

2. DO NOT allow the pump to run dry.

3. For fountains with multiple sections or attached decorations: If any of the fountain’s attached

sections with electrical lights or components fall into the water located in fountain base, unplug the

fountain and turn off circuit breaker before trying to put the fountain pieces back in place.

4. If any leakage occurs around the pump housing, turn off the circuit breaker immediately and have

the pump serviced by a registered technician.

5. Do not operate the fountain if the pump has been dropped or has a damaged power cord or plug.

6. If the plug or your wall receptacle gets wet due to water dripping down the power cord or for any

other reason, do not remove the plug from the wall outlet until the circuit breaker is turned off.

7. Always unplug the fountain pump and any other independent electrical accessories (e.g. lights)

from the outlet when not in use and before cleaning or replacing parts.

8. Disconnect the power cord from the outlet by holding the plug, not by pulling on the power cord.

9. Do not expose the pump to direct sunlight or to low temperatures for any period of time.

10. Keep the power cord away from high temperatures or heat sources.

11. This fountain pump is not intended for commercial use.

NOTE: Allow the pump power cord to hang at a lower level than

the wall outlet to form a “drip loop”. This will help prevent water

from dripping down the power cord and getting into the wall outlet.

PACKAGE CONTENTS

Top fountain

Fountain base

Pump

Water flow rate control valve assembly

Reservoir lid

ITEM DESCRIPTION QUANTITY

A 1

C 1

Glass bead

F1 bag

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 10 minutes

HARDWARE CONTENTS

AA BB CC DD EE

Silicone plug

M8xL30Screw

Washer

Plastic cap

Spanner

ITEM DESCRIPTION QUANTITY

AA 2

BB4

CC 4

DD4

EE1

Tools required for assembly (included): Spanner

ASSEMBLY INSTRUCTIONS

1. Remove all packaging from all parts.

Connect the two long flexible hoses on the water

flow rate control valve assembly (C) to the inlets

on the bottom side of the top fountain (A).

3. Block the drain hole at the bottom of the fountain

base (B) with the silicone plug (AA).

2. Connect the short hose on the water flow rate

control valve assembly (C) to the outlet of the pump

(E).

NOTE: Just need one silicone plug for assembly,

another one is a spare part.

AA B

ASSEMBLY INSTRUCTIONS

4. Insert and pull out the power cord plug of the

pump through the hole on the side wall of the

fountain base (B).

5. Place the pump (E) into the fountain base (B)

and attach the top fountain (A) to the fountain

base using 4 M8xL30screws (BB) and 4 washers

(CC), tighten with spanner (EE). Then buckle the

6. Pour clean water into fountain base through

the operation hole on the bottom plate of top

fountain (A), make sure the water pump is fully

submerged to prevent pump damage. View the

water level through the operation hole, make

sure the the water level is between the Max fill

line and Min fill line on the wall inside the fountain

base (B).

NOTE: Make sure the operation hole on the top

4 plastic caps (DD).

fountain align with the drain hole at the bottom

of the fountain base.

ASSEMBLY INSTRUCTIONS

7. Cover the operation hole on the bottom plate of

the top fountain (A) with the reservoir lid (D).

8. 3OXJSXPScordplug LQWRRXWOHW of power supply

7KHZDWHUÀRZUDWHFDQEHLQFUHDVHGRUGHFUHDVHGE

\PRYLQJWKHÀRZrate controller on the water pump

to the +/- signs. If the flow is not same for the two

outlets, adjust the knobs on the water flow rate control

valve assembly (C).

CAUTION:

Be careful not to spill water onto the plug of the pump.

DO NOT allow the pump to run dry!

Adjust the feet under the fountain base (B) to make

it level. Pour glass bead (F) into the fountain base

evenly.



Flow rate

adjusting

knob

OPERATING INSTRUCTIONS

While fountain is designed to operate as splash free as possible, some water splashing out of the

fountain is inevitable. Place the fountain in a location where any splashing will not cause damage.

Always keep the fountain working with sufficient water and clean of debris and dirt to ensure proper

functioning of the pump.

Adjust the flow rate to achieve the desired effect and to minimize any splashing. Splashing can occur

if the flow rate is too high or the reservoir is too full. The flow rate can be increased or decreased by

moving the flow rate control switch towards the ‘+/max’ or ‘-/min’ positions.

Note:

1. Drain the water if you don’t plan to use the fountain for a long time to prevent mosquito breeding

and water odor.

2. Be sure to drain all water during winter months or cold seasons to prevent reservoir from cracking

or breaking.

Operating Fountain

ALWAYS MAKE SURE THE PUMP IS FULLY SUBMERGED UNDER THE WATERLINE PRIOR TO

TURNING PUMP ON.

1. Check that there is enough water in the reservoir.

2. Plug in pump cord into outlet and switch on, pump will start to work.

3. The water flow rate can be increased or decreased by moving the flow rate controller on the water

pump to the +/- signs.

4. Turn off power outlet switch, the pump will stop working.

5. Unplug fountain from outlet if not in use for a long period of time.

3. The method of draining water: Unplug the power cord for pump from power supply, remove the

reservoir lid (D) from the bottom plate of top fountain (A), then remove the silicone plug (AA) at the

bottom of the fountain base (B) through the operation hole.

WARNING: Please check and

ensure the power cord is not dam-

aged before using this appliance.

Minimum Water Level

Flow control valve

(+)Maximum

(-)Minimum

CARE AND MAINTENANCE

• If necessary, clean the fountain with a soft cloth and change the water frequently. Due to water

evaporation, you may see a buildup of white residue on the fountain surface from mineral content in

the water supply. To prevent such buildup, regularly clean the fountain with soap and water. Do not

use any abrasive, which may damage the applied finish.

• Use of water clarifier or algaecide of any kind will damage the paint on the fountain and will not be

covered under the manufacturer’s warranty.

• Check regularly that the water reservoir has sufficient water to cover the pump at all times. It will be

necessary to check more frequently in warm or windy weather.

• Disconnect the power and empty the reservoir if the fountain will not be used for an extended time.

• If installed outdoors and in a freeze-prone area of the country, ensure all water is removed and

the unit is completely dry before temperatures drop too low. This product is NOT to be operated

below 41°F or freeze damage may occur.

• Store your product indoors during the winter months. Avoiding extreme cold temperatures

will prevent from exposure damage.

• Keep this manual for future reference.

Model# Description Volt. Power

YH-LV250C water

pump 120 V

Frequency Flow Height Flow Volume

60 Hz 780L/hour

NOTE: The pump data in this manual is from

lab tests. The actual pump may be different

due to the method of production or technical

improvements. This data can be used as a

reference when purchasing a similar pump.

Outlet

Suction cap

Pump housing

Rotor Gland

Filter

18W

190cm

Water level controller

Inhaltsverzeichnis

Sprachen:

Andere Bond Rasen- und Gartengeräte Handbücher

Bond

Bond 52108 Bedienungsanleitung

Bond

Bond 1077438 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung