Bosch 715ES Referenzhandbuch

Models: 715ES, C800ES, C920ES, C920ESC, 2400ES, 2700ES

Replacing gas valve

Service Bulletin G3-28

Introduction

This procedure must be performed by a licensed gas technician

with a calibrated combustion gas analyzer.

 The gas valve is not gas type specic but requires different CO₂

values when calibrating for different gas types.

Tools needed:

Phillips head screwdriver

 Small at head screwdriver

#40 Torx driver

 Combustion gas analyzer

30mm open end wrench or large adjustable wrench

4mm allen wrench

Preparation

1. Unplug water heater and turn off gas to heater using installer

supplied manual shut off valve.

2. Loosen two Phillips head screws located at bottom rear of cover.

(Fig. 1, step 1, pos. 1).

3. Lift front cover upward and remove. (Fig. 1, step 1, pos. 2 & 3)

Step 1 Step 2

tep

Figure 1

4. Remove combustion cover by unclipping two upper and two

lower clips securing cover. (Fig. 1, step 2)

5. Remove 3 Phillips screws on control unit (Fig. 2, step 1). Place

control unit into the service postion by engaging its tabs with

the holes in the horizontal sheet metal on bottom of the heater

chassis . (Fig. 2, step 2).

Step 2

Step 1

tep

Step

Figure 2

Gas

Valve

Removing the gas valve

1. Unplug wire connection from gas valve. (Fig. 3, pos. 1).

2. Disconnect clear silicone pressure balance tube from right side

of gas valve. (Fig. 3, pos. 2)

3. Loosen and disconnect large 30mm hex nut on the left side of

gas valve. (Fig. 3, pos. 3).

4. Unscrew the three 4mm allen screws from the top of the gas

valve. (Fig. 3, pos. 4).

5. Remove gas valve from the water heater.

http://waterheatertimer.org/Troubleshoot-Bosch-Tankless-water-heaters.html

Data subject to change without notice | Printed in the USA | BTC 710002312 A | 01.2009 Bosch Thermotechnology Corp.

Service bulletin

18 | G3-28 | 715ES, C800ES, C920ES, C920ESC, 2400ES, 2700ES

Bosch Thermotechnology Corp.

50 Wentworth Avenue

Londonderry, NH 03053

Tel: 1-866-642-3198

Fax: 1-603-584-1681

www.boschhotwater.com

Figure 3

Installing gas valve

1. Replace both the grey ber washer on the left side of the gas

valve and the rubber gasket on the top of the gas valve.

2. Hold replacement gas valve in place and reinstall the three allen

screws into the top of the gas valve. (Fig. 3, pos. 4).

3. Reinstall 30mm hex nut on the left side of gas valve.

(Fig. 3, pos. 3)

4. Open manual gas shutoff valve and check for leaks at all connec-

tions.

5. Reinstall silicone pressure balance tube to right side of gas

valve. (Fig. 3, pos. 2).

6. Reconnect wire connection to gas valve. (Fig. 3, pos. 1).

Calibrating gas valve

1. Reinstall combustion cover. (Fig. 1, step 2).

2. Return control unit to normal position and secure with 3 Phillips

head screws. (Fig. 2)

3. Plug in water heater and push power button to the "ON" posi-

tion.

4. Open a hot water tap. If heater res, adjust CO₂ using service

bulletin G3-12 Measuring and adjusting CO₂.

5. If the heater does not fire, allow the unit to display the EA error

code and shut off hot water tap. The fan will continue to run to

purge the heater of gasses. Continue to the next section for a

rough gas valve adjustment.

Rough gas valve adjustment

Note: Do not forcefully tighten adjustment screws past bottom out

point. Stop bottoming out screw when resistance is felt. Failure

to do so will damage the gas valve.

1. Locate adjustment screw on gas valve. Loosen Phillips head

screw so retaining cover can be rotated to expose brass slotted

screw. (Fig. 4, pos. 1 & 2).

2. Turn brass slotted screw clockwise gently until it bottoms out

and/or screw resistance increases. (Fig. 4, pos. 3).

Figure 4

3. Once the slotted screw is bottomed out, make the following

adjustment to the slotted screw depending on your model and

gas type. (Fig. 4, pos. 3)

For models GWH 715 ES/GWH 2700 ES/ GWH 2400 ES:

Natural Gas: 2.5 turns counter-clockwise on brass slotted screw

Liquid Propane: .75 turns counter-clockwise on brass slotted screw

For model GWH C 800 ES:

Natural Gas: 3 turns counter-clockwise on brass slotted screw

Liquid Propane: 1 turn counter-clockwise on brass slotted screw

For models GWH C920 ES/GWH C 920 ESC:

Natural Gas: 2.5 turns counter-clockwise on brass slotted screw

Liquid Propane: Leave brass slotted screw bottomed out

4. Open a hot water tap. If heater res, adjust CO₂ using service

bulletin G3-12 Measuring and adjusting CO₂. If heater still does

not re, contact Bosch Thermotechnology Corp.

5. Reinstall brass slotted screw cover and secure with Phillips

screw. (Fig. 4, pos. 1 & 2).

!WARNING

FAILURE TO PROPERLY CALIBRATE THE

HEATER’S CO₂ LEVEL MAY RESULT IN A

HAZARDOUS CONDITION CAUSING

SEVERE PERSONAL INJURY OR DEATH.

Andere Handbücher für 715ES

Dieses Handbuch passt für folgende Modelle

Andere Bosch Steuereinheit Handbücher

Bosch

Bosch Rexroth IndraControl XFE 01.1 Series Bedienungsanleitung

Bosch

Bosch IOS 0232 A Bedienungsanleitung

Bosch

Bosch CRR 120 Einrichtungshandbuch

Bosch

Bosch Rexroth IMpdp Bedienungsanleitung

Bosch

Bosch IO-BOX32 Bedienungsanleitung

Bosch

Bosch Rexroth R-IB IL 24 PSDO 8-PAC Bedienungsanleitung

Bosch

Bosch Rexroth VM350 Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl Bedienungsanleitung

Bosch

Bosch FLM-420-O2-E Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl VCP 20.2 Technisches Handbuch

Bosch

Bosch Rexroth VKK Series Bedienungsanleitung

Bosch

Bosch Rexroth 4WS2EM 10 Series Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl VAC 05.1 Bedienungsanleitung

Bosch

Bosch Rextroth Indramat RECO R-IB IL CNT Gebrauchsanweisung

Bosch

Bosch Rexroth IndraControl L10 Technisches Handbuch

Bosch

Bosch B426 Bedienungsanleitung

Bosch

Bosch KTS Truck Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl XFE 01.1 Series Bedienungsanleitung

Bosch

Bosch D9133TTL-E Bedienungsanleitung

Bosch

Bosch Junkers MB LAN Bedienungsanleitung

Bosch

Bosch B901 Bedienungsanleitung

Bosch

Bosch ATB 420 LSNi Installations- und Betriebshandbuch

Bosch

Bosch FM441/CMM 910 Bedienungsanleitung

Bosch

Bosch Rexroth M SED 10 XN Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung