Bosch D7039 Bedienungsanleitung
D7039
EN
Installation Guide
Multiplex Expansion
Module
Bosch | 09/05 | 38685F2
D7039 | Installation Guide |
Notices
Use these instructions to install the D7039 Multiplex
Expansion Module in a fire system supervised by a
D7024 Fire Alarm Control Panel (FACP).
Install, test, and maintain the D7039 according to these
instructions, NFPA 72, local codes, and the Authority
Having Jurisdiction (AHJ).
Follow the procedures in this document to
avoid personal injury and damage to the
equipment. Failure to follow these
procedures can cause the D7039 to not
operate properly. Bosch is not responsible
for improperly installed, tested, or maintained
devices.
For the D7039 with ROM version 1.04 to
operate properly, the D7024 FACP must be
running version 2.05 or later firmware.
1.0 Description
The D7039 (Figure 1) connects directly to the FACP for
either two Class B multiplex buses or one Class A
multiplex bus that allows up to 247 remote points.
When configured for Class A operation,
the D7039 can only support Addresses 9
through 128.
Notices
21 3
4 5 6
7 8 9
#
Cmnd
0
Prog
*
Clear
Disable
Drill
Test
Histo ry
Reset
Silence
Trouble
Silenced
Power
Alarm
1
2
3
4
1 - D7024 Control Board
2 - Enclosure
3 - I/O module for the D7039
4 - D7039 Module
Figure 1: D7039 Module Location
3Bosch | 09/05 | 38685F
D7039 | Installation Guide | 2.0 Installation
2.0 Installation
Failure to follow the mounting instructions in this document can damage the FACP.
The D7039 and D7024 have static sensitive components and must be handled with care. Follow the
anti-static procedures when handling these modules.
Before installing the D7039 Module, remove all AC and battery power to the FACP.
1. If the D7024 is already installed in an enclosure, remove it.
2. Place the FACP on a flat surface with the component side facing up (Item 2 in Figure 2).
3. Insert the four plastic standoffs in the mounting holes (Item 3 in Figure 2) without bending or flexing the FACP.
4. Align the standoff tabs so they do not touch the module components.
5. Firmly press the standoffs into the board, allowing the ears to expand out.
6. Mount the D7039 on the standoffs, ensuring the FACP connector pins (Item 4 in Figure 2) are properly aligned.
7. Install the FACP in the enclosure.
8. Use the mounting screw (Item 5 in Figure 2) to secure the D7039’s ground wire (Item 6 in Figure 2) to the FACP.
21 3
4 5 6
7 8 9
#
Cmnd
0
Prog
*
Clear
Disable
Drill
Test
History
Reset
Silence
Trouble
Silenced
Power
Alarm
12
6
3
4
3
5
1 - D7039 Module 4 - FACP connector pins to align with the D7039
2 - D7024 FACP 5 - Mounting screw
3 - Standoff mounting holes (4) 6 - Ground wire
Figure 2: Mounting the D7039 on the D7024
Bosch | 09/05 | 38685F4
D7039 | Installation Guide |
9. Mount the D7039 I/O Module (Item 1 in Figure 3) in the FACP enclosure (Item 2 in Figure 3) using the mounting
holes in the enclosure (Item 3 in Figure 3).
10. Connect the yellow and green earth ground wire from the I/O module to the earth ground terminal on the
FACP control board (Item 4 in Figure 3).
3.0 Wiring
1. Connect the D7039 multiplex loop using up to 3800 ft (1170 m) of 18 AWG (1.0 mm2) or 5950 ft (1810 m) of
16 AWG (1.5 mm2) wire (Figure 4). Do not use shielded wire.
Do not use shielded wire. Twisted pair is acceptable, but is not recommended.
2.0 Installation
Figure 4: Connecting the Mux Class “A” and Class “B”
1 - I/O module for the D7039, wired Class “A” 4 - Mux B Addresses 129 through 255
2 - Class “A” Addresses 9 through 128 5 - Mux A Addresses 9 through 128
3 - I/O module for the D7039, wired Class “B”
Note: All terminals are supervised.
21 3
4 5 6
7 8 9
#
Cmnd
0
Prog
*
Clear
Disable
Drill
Test
History
Reset
Silence
Trouble
Silenced
Power
Alarm
2
1
3
4
1 - I/O module 3 - Holes (3) and standoffs (3) to mount the I/O module
2 - Enclosure 4 - I/O module earth ground wire to the D7024 terminal connection
Figure 3: Installing the Input-Output Module
5Bosch | 09/05 | 38685F
D7039 | Installation Guide | 4.0 Specifications
Figure 5: Measuring Class “B” Loop Resistance
1 - 50
Ω
maximum 2 - Mux bus wires 3 - Clip lead
Figure 6: Measuring Class “A” Loop Resistance
1 - 50
Ω
maximum 2 - Mux bus wires 3 - Clip lead
You can configure the D7039 with a single fault tolerant Class “A” loop or as a pair of supervised Class “B”
loops. When configured as a Class “A” loop and installed on a D7024 Control Panel before Lot #100, the
D7039 implements a Style 4.5 signaling line circuit (SLC). When installed on a D7024 Control Panel Lot #100
or later, the D7039 implements Style 6 SLC. Refer to the D7024 Operation and Installation Guide (P/N: 31499)
for programming.
When configured as a Class “B” loop and installed on a D7024 Control Panel before Lot #100, the D7039
implements a Style 3.5 SLC. When installed on a D7024 Control Panel Lot #100 or later, the D7039
implements a Style 4 SLC. Refer to the D7024 Operation and Installation Guide (P/N: 31499) for programming.
2. Measure loop resistance by shorting the end of the farthest device in Class “B” (Figure 5) or shorting the return
wire in Class “A” (Figure 6) and reading the total resistance of all wires associated with the loop.
3. Ensure the loop is disconnected from the D7039 Module.
Bosch | 09/05 | 38685F6
D7039 | Installation Guide |Notes
4.0 Specifications
Table 1: Specifications
Input Voltage 24 VDC nominal from FACP
Current Draw, Standby
and Alarm
150 mA maximum
Current Draw Load 100 mA maximum for each bus
Maximum Bus Voltage 8.5 V to 13 V
Maximum Wiring
Resistance
50 Ω, Class A (Style 6) or Class B (Style 4) SLC
Environment Indoor/dry
Note: All Mux Bus terminals are power-limited and supervised.
7Bosch | 09/05 | 38685F
D7039 | Installation Guide | Notes
Notes
Bosch
130 Perinton Parkway
Fairport, NY 14450-9199 USA
Customer Service: (800) 289-0096
Technical Support: (888) 886-6189
© 2005 Bosch
38685F
Inhaltsverzeichnis
Andere Bosch Steuereinheit Handbücher
Bosch
Bosch CM255B Anleitung zur Verwendung
Bosch
Bosch B442 Bedienungsanleitung
Bosch
Bosch Rexroth FMS Bedienungsanleitung
Bosch
Bosch MP 100 Bedienungsanleitung
Bosch
Bosch KTS 5 Series Bedienungsanleitung
Bosch
Bosch Control 8313 Betriebsanleitung
Bosch
Bosch FM441/CMM 910 Bedienungsanleitung
Bosch
Bosch C900TTL-E Bedienungsanleitung
Bosch
Bosch rexroth DB20K.1X E Series Bedienungsanleitung
Bosch
Bosch B444 Bedienungsanleitung
Bosch
Bosch Rexroth NYM04.1-5PW-NNNN-NY4125 Bedienungsanleitung
Bosch
Bosch ICP-COM-IF Bedienungsanleitung
Bosch
Bosch ConnectModule BCM3100 Bedienungsanleitung
Bosch
Bosch Rexroth ctrlX I/O XI322204 Bedienungsanleitung
Bosch
Bosch Rexroth M4-12 Betriebsanleitung
Bosch
Bosch Rexroth BVD 52 Series Bedienungsanleitung
Bosch
Bosch B426 Bedienungsanleitung
Bosch
Bosch FLM-420-EOL2W-W Bedienungsanleitung
Bosch
Bosch API-AMC2-4WE Bedienungsanleitung
Bosch
Bosch MS 6 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
