Bosch AMC-4W Bedienungsanleitung

Access Controller

AMC-4W

Bosch Security Systems | V.3.1/2006-09

Trademarks Access Controller AMC-4W

2 Installation Guide Bosch Security Systems | V.3.1/2006-09

Trademarks

Bosch is a registered trademark of Bosch Security Systems in the United States

and/or other countries.

Remarks

This hardware is part of a security system. Access shall be limited to

authorized persons only.

Some states do not allow the exclusion or limitation of implied warranties, or

limitation of liability for incidental or consequential damages, so the above

limitation or exclusion might not apply to you.

Bosch Security Systems retains all rights not expressly granted. Nothing in this

license constitutes a waiver of Bosch’s rights under the U.S. Copyright laws or

any other federal or state law.

If you have any questions concerning this license, please, write to:

Bosch Access Systems GmbH

Adenauerstr. 20 / A3

D-52146 Würselen

Germany.

Access Controller AMC-4W Contents

Bosch Security Systems | V.3.1/2006-09 Installation Guide 3

Contents

1. Please, read the following notes carefully.........................................5

1.1. Explanation of Used Symbols .............................................................. 5

1.2. Internet.................................................................................................. 5

1.3. We Are Interested in Your Opinion...................................................... 5

2. Safety Instructions..............................................................................6

2.1. Important Safety Notes......................................................................... 6

2.2. FCC & ICES Information..................................................................... 8

2.3. Safety Precautions ................................................................................ 9

2.4. Unpacking .......................................................................................... 10

3. Description of the AMC-4W............................................................11

3.1. Equipment Configuration ................................................................... 13

3.2. Performance Characteristics ............................................................... 16

3.3. System Overview................................................................................ 17

4. Technical Data..................................................................................18

5. Installing the AMC-4W....................................................................21

5.1. Mounting the AMC-4W ..................................................................... 21

5.1.1. Mounting on rails ............................................................................... 21

5.1.2. Demounting the AMC-4W from mounting rails ................................ 21

5.2. Opening the AMC-4W Case............................................................... 22

5.3. Cabling ............................................................................................... 22

5.4. Grounding and Shielding.................................................................... 23

5.5. Connecting Power Supply .................................................................. 25

5.6. RS485 Host Interface.......................................................................... 27

5.6.1. RS485 Two Wire Connection............................................................. 28

5.6.2. RS485 Four Wire Connection ............................................................ 29

5.6.3. DIL Switch Address Selector ............................................................. 30

5.7. RS232 Host Interface.......................................................................... 32

5.8. Ethernet Interface ............................................................................... 33

5.8.1. Removing Ethernet Plugs from Socket............................................... 33

5.9. RS485 Extension Module Bus............................................................ 34

5.10. Wiegand Interface for Card Readers .................................................. 35

5.11. Connecting Relay Outputs.................................................................. 36

Contents Access Controller AMC-4W

4 Installation Guide Bosch Security Systems | V.3.1/2006-09

5.12. Connecting Analog Input Devices...................................................... 38

5.13. Tamper Protection .............................................................................. 40

6. Operating the AMC-4W ..................................................................41

6.1. Status Display of the AMC-4W.......................................................... 41

6.2. Configuring the Ethernet Interface ..................................................... 42

6.3. Resetting the AMC-4W...................................................................... 42

7. Appendix...........................................................................................44

7.1. Connecting Diagrams ......................................................................... 44

7.2. Jumpers............................................................................................... 48

7.3. Proprietary burglar alarm/access control power supply .............Fehler!

Textmarke nicht definiert.

7.3.1. Overview ......................................Fehler! Textmarke nicht definiert.

7.3.2. Power Supply Voltage Output Selections..... Fehler! Textmarke nicht

definiert.

7.3.3. LED Diagnostics ..........................Fehler! Textmarke nicht definiert.

7.3.4. Installation Instructions for the RK-AL600ULX-4CB6.............Fehler!

Textmarke nicht definiert.

7.4. Legend................................................................................................ 50

7.5. Product declaration............................................................................. 51

7.6. Listings and Approvals....................................................................... 51

7.6.1. FCC Notice......................................................................................... 51

7.6.2. UL Listing .......................................................................................... 51

7.6.3. Safety.................................................................................................. 51

7.7. Included in delivery............................................................................ 51

8. List of Figures...................................................................................52

9. Index..................................................................................................54

Access Controller AMC-4W Please read the following notes carefully

Bosch Security Systems | V.3.1/2006-09 Installation Guide 5

1. Please read the following notes carefully

1.1. Explanation of Used Symbols

Throughout this document, helpful tips, important notes, cautions and warnings

will be presented for the reader to keep in mind. These appear different from

the rest of the text as follows:

Caution!

These warn the operator that damage to the program or equipment

might occur.

Important Notes – must be followed for successful operation and

programming. Tips and shortcuts might also be included here.

Cross Reference

Please, refer to this document or chapter to obtain additional

information about the issue.

1.2. Internet

If you are interested in further information on this product or information on

other products, please, refer to our website at http://www.bosch-security-

systems.com.

1.3. We Are Interested in Your Opinion

We constantly improve the quality of our products and our manuals. Should

you have any suggestions for improvement, please, send us your comments.

Bosch Security Systems

Adenauerstr 20 / A3

D-52146 Würselen

Germany

Tel.: +49 24 05 / 60 05-0

Fax: +49 24 05 / 60 05-29

Email: [email protected]h.com

Safety Instructions Access Controller AMC-4W

6 Installation Guide Bosch Security Systems | V.3.1/2006-09

2. Safety Instructions

2.1. Important Safety Notes

1. Read, Follow, and Retain Instructions −All safety and operating

instructions must be read and followed properly before putting the unit into

operation. Retain instructions for future reference.

2. Consider all Warnings −Adhere to all warnings on the unit and in the

operating instructions.

3. Accessories −Use only accessories recommended by the manufacturer or

those sold with the product. Accessories not recommended by the

manufacturer shall not be used, as they may cause hazards.

4. Installation Precautions −Do not place this unit on an unstable stand,

tripod, bracket, or mount. The unit may fall, causing serious injury to

persons and damage to the unit. Mount the unit according to the

manufacturer’s instructions.

5. Cleaning −Disconnect the unit from power before cleaning. Follow any

instructions provided with the unit. Generally, using a damp cloth for

cleaning is sufficient. Do not use liquid cleaners or aerosol cleaners.

6. Service −Do not attempt to service this unit by yourself. Opening or

removing covers may expose you to dangerous voltages or other hazards.

Refer all servicing to qualified service personnel.

7. Damage Requiring Service −Disconnect the unit from the main AC or

DC power source and refer servicing to qualified service personnel under

the following conditions:

•When the power supply cord or plug is damaged.

•If liquid has been spilled or an object has fallen into the unit.

•If the unit has been exposed to water and/or inclement weather (rain,

snow, etc.).

•If the unit does not operate normally, when following the operating

instructions. Adjust only those controls specified in the operating

instructions. Improper adjustment of other controls may result in

damage, and require extensive work by a qualified technician to

restore the unit to normal operation.

•If the unit has been dropped or the cabinet damaged.

•If the unit exhibits a distinct change in performance, this indicates that

service is needed.

Access Controller AMC-4W Safety Instructions

Bosch Security Systems | V.3.1/2006-09 Installation Guide 7

8. Replacement Parts −When replacement parts are required, the service

technician shall use replacement parts that are specified by the

manufacturer. Unauthorized substitutions may result in fire, electrical

shock or other hazards.

9. Safety Check −Upon completion of service or repair work on the unit, ask

the service technician to perform safety checks to ensure that the unit

operates properly

10. Power Sources −Operate the unit only from the type of power source

indicated on the label. If unsure of the type of power supply to use, contact

your dealer

•For units intended to operate from battery power, refer to the operating

instructions.

•For units intended to operate with External Power Supplies, use only

the recommended approved power supplies.

•For units intended to operate with a limited power source, this power

source must comply with EN/UL 60950. Substitutions may damage

the unit or cause fire or shock.

•For units intended to operate at 12 VDC normal input voltage is 12

VDC. Voltages applied to the unit’s power input shall not exceed 15

VDC. User-supplied wiring, from the 12 VDC power supply to the

unit, must be in compliance with electrical codes (Class 2 power

levels). Do not ground the 12 VDC supply at the terminals or at the

unit’s power supply terminals.

11. Grounding −If an outside cable system is connected to the unit, ensure

that the cable system is grounded. U.S.A. models only Section 810 of the

National Electrical Code, ANSI/ NFPA No.70, provides information

regarding proper grounding of the mount and supporting structure,

grounding of the coax to a discharge unit, size of grounding conductors,

location of discharge unit, connection to grounding electrodes, and

requirements for the grounding electrode.

12. Grounding and Protection against reverse Polarity −This unit may be

equipped with a polarized alternating current line plug (a plug with one

blade wider than the other). This safety feature allows the plug to fit into

the power outlet in only one way. If unable to insert the plug fully into the

outlet, try reversing the plug. If the plug still fails to fit, contact an

electrician to arrange replacement of the obsolete outlet. Do not defeat the

safety purpose of the polarized plug. Alternately, this unit may be equipped

with a 3−wire grounding plug (a plug with a third pin, for grounding). This

safety feature allows the plug to fit into a grounding power outlet only. If

unable to insert the plug into the outlet, contact an electrician to arrange

Safety Instructions Access Controller AMC-4W

8 Installation Guide Bosch Security Systems | V.3.1/2006-09

replacement of the obsolete outlet. Do not defeat the safety purpose of the

grounding plug.

13. Lightning −For added protection during a lightning storm, or when this

unit is left unused for long periods of time, disconnect the unit from power.

This will prevent damage to the unit due to lightning and excessive power

line surges.

14. Restricted Access Locations are required for the installation.

2.2. FCC & ICES Information

This equipment generates and uses radio frequency energy. If not installed and

used in accordance with the manufacturer's instructions, it may cause

interference to radio and television reception. It has been tested and found to

comply with the specifications Subpart B of Part 15 of FCC rules for Field

Disturbance Sensors. If this equipment causes interference to radio or television

reception - which can be determined by turning the equipment on and off - the

installer is encouraged to correct the interference by one or more of the

following measures:

1. Reorient the antenna of the radio/television,

2. Connect the AC power cord to a different outlet so the control panel and

radio/television are on different branch circuits,

3. Relocate the control panel with respect to the radio/television.

If necessary, consult an experienced radio/television technician for additional

suggestions, or send for the "Interference Handbook" prepared by the Federal

Communications Commission. This booklet is available from the:

U.S. Government Printing Office,

Washington D.C. 20402,

Stock no. 004-000-00450-7.

FCC Registration Number: IDHM32Y6K2000

Intentional or unintentional changes or modifications that are not explicitly

approved by the party responsible for compliance, shall not be made. Any such

changes or modifications could nullify the user’s authority to operate the

equipment.

The user may find the following booklet, prepared by the Federal

Communications Commission, helpful: How to Identify and Resolve Radio-TV

Interference Problems. This booklet is available from the U.S. Government

Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.

Access Controller AMC-4W Safety Instructions

2.3. Safety Precautions

Read instructions!

Before working with the AMC-4W, read these instructions carefully.

Make sure you have understood all information described in this

document.

Warning! Risk of electric shock!

External power supplies must be installed and put into service by

qualified personnel. Compliance with the relevant regulations must be

ensured.

Warning! Risk of damaging equipment!

-Always switch off power of the AMC-4W before modifying

the installation.

-Do not connect or disconnect plug connectors, data cables or

screw connectors while power is on!

Health and Safety

Installation of the AMC-4W must comply with any local fire, health

and safety regulations. A secured door that may be part of an escape

route from an area must be installed with:

•A fail-safe lock (A). So that the door will be released if

power fails. Ideally, a magnetic lock should be used as these

are less likely to jam or seize.

•A normally-closed break-glass or manual pull (B) in the lock

supply wiring, so that in an emergency the fail-safe lock can

be immediately powered down.

You must ground the AMC-4W. Disconnect both AC and battery

power supply before working on the controller.

Bosch Security Systems | V.3.1/2006-09 Installation Guide 9

Safety Instructions Access Controller AMC-4W

10 Installation Guide Bosch Security Systems | V.3.1/2006-09

Warning! Risk of damage!

Protect the hardware from electrostatic discharge by observing ESD

instructions before unpacking or touching connectors or electronics.

CAUTION: Lithium Battery

Danger of explosion if battery is replaced incorrectly. Replace only

with the same type as recommended by the manufacturer. Dispose

used batteries according to the battery manufacturer’s instructions.

2.4. Unpacking

Check the packaging for visual damage. If anything has been damaged during

transport, make the transport agency aware of this.

Carefully unpack the unit. This is an electronic device that must be handled

with care to avoid damage. Do not attempt to put the unit into operation if

components are damaged.

If parts are missing, inform your customer service representative or a Bosch

Security Systems salesperson. The shipping carton is the safest transport

container for the unit. Store it and the other packaging material for future use. If

the unit has to be sent back, use the original packaging.

Inhaltsverzeichnis

Andere Bosch Controller Handbücher

Bosch

Bosch AMC2-16IOE Bedienungsanleitung

Bosch

Bosch ARC R-1 Betriebsanleitung

Bosch

Bosch CL550 Bedienungsanleitung

Bosch

Bosch KJR-120C1/BTF-E Betriebsanleitung

Bosch

Bosch Rexroth IndraControl VPB 40.3 Bedienungsanleitung

Bosch

Bosch CLIMATE 5000 VRF RDCI Series Bedienungsanleitung

Bosch

Bosch rexroth SB11 Bedienungsanleitung

Bosch

Bosch Rexroth Diax 04 Bedienungsanleitung

Bosch

Bosch Rexroth IndraDrive HMS02 Bedienungsanleitung

Bosch

Bosch AMC2 Series Bedienungsanleitung

Bosch

Bosch REXROTH IndraDrive Bedienungsanleitung

Bosch

Bosch Access Modular Controller 2 Bedienungsanleitung

Bosch

Bosch Rexroth ctrl CORE Bedienungsanleitung

Bosch

Bosch REXROTH SB356 Bedienungsanleitung

Bosch

Bosch AMC2 Series Bedienungsanleitung

Bosch

Bosch AMC2 Series Bedienungsanleitung

Bosch

Bosch 2600 Series Bedienungsanleitung

Bosch

Bosch MPC 2000 A Bedienungsanleitung

Bosch

Bosch FMR-7033 Bedienungsanleitung

Bosch

Bosch Rexroth IndraDrive C HCS03.1 Technisches Handbuch

Bosch

Bosch Intuvia BUI255 Bedienungsanleitung

Bosch

Bosch ADS-AMC2-4R4CF Bedienungsanleitung

Bosch

Bosch Rexroth 31 Series Gebrauchsanweisung

Bosch

Bosch PVA-4CR12 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch