Bosch AMC2 Series Bedienungsanleitung

AMC2 Modular Controller

AMC2‑4R4

en Installation Manual

AMC2 Modular Controller Table of contents | en 3

Bosch Access Systems GmbH Installation Manual 2018-02 | AMC2-4R4 |

Table of contents

1Safety Instructions 4

1.1 Important Safety Notes 4

1.2 Safety Precautions 5

1.3 Unpacking 6

2Important Information 7

2.1 Explanation of symbols in this document 7

2.2 Internet 7

3Introduction 8

3.1 Description 8

3.2 Equipment Configuration 9

3.3 Performance Characteristics 11

3.4 System Overview 12

4Installing 13

4.1 Mounting 13

4.2 Unmounting 14

4.3 Opening the Case 15

4.4 Closing the Case 16

4.5 Cabling 16

4.5.1 Conductor data for power to AMC2 16

4.6 Grounding and Shielding 18

4.6.1 Grounding for Host Interface 18

4.6.2 Grounding for Extension Interface 19

4.6.3 Grounding for Bus Interfaces 19

4.7 Connecting Power Supply 20

4.8 Ethernet Host Interface 21

4.9 RS-485 Host Interface 22

4.9.1 RS-485 Two Wire Connection 23

4.9.2 RS-485 Four Wire Connection 24

4.10 RS-232 Host Interface 25

4.11 DIL switch selector 26

4.11.1 Host settings 26

4.12 RS-485 for extension modules 27

4.13 RS-485 Interface for Card Readers 29

4.14 Connecting Relay Outputs 30

4.15 Connecting Analog Input Devices 33

4.16 Tamper Protection 35

5Operating 36

5.1 Status Display of the AMC2 36

5.2 Configuring the Ethernet Interface 38

5.3 Troubleshooting 39

5.3.1 Resetting the Software 39

5.3.2 Resetting the Device to Factory Default 40

6Technical Data 41

7Appendices 44

7.1 Connecting Diagrams 44

Index 49

4en | Safety Instructions AMC2 Modular Controller

2018-02 | AMC2-4R4 | Installation Manual Bosch Access Systems GmbH

1 Safety Instructions

1.1 Important Safety Notes

1. Read, follow, and retain instructions - All safety and operating instructions must be read

and followed properly before putting the unit into operation. Retain instructions for

future reference.

2. Do not ignore warnings - Adhere to all warnings on the unit and in the operating

instructions.

3. Accessories - Use only accessories recommended by the manufacturer or those sold with

the product. Accessories not recommended by the manufacturer must not be used, as

they may cause hazards.

4. Installation precautions - Do not place this unit on an unstable stand, tripod, bracket, or

mount. The unit may fall, causing serious injury to persons and damage to the unit. Mount

the unit according to the manufacturer’s instructions.

5. Service - Do not attempt to service this unit by yourself. Opening or removing covers may

expose you to dangerous voltages or other hazards. Refer all servicing to qualified service

personnel.

6. Damage which requires service - Disconnect the unit from the main AC or DC power

source and refer servicing to qualified service personnel under the following conditions:

– If the power supply cord or plug is damaged.

– If liquid has been spilled or an object has fallen into the unit.

– If the unit has been exposed to water and/or inclement weather (rain, snow, etc.).

– If the unit does not operate normally when following the operating instructions.

Adjust only those controls specified in the operating instructions. Improper

adjustment of other controls may result in damage, and require extensive work by a

qualified technician to restore the unit to normal operation.

– If the unit has been dropped or the cabinet damaged.

– If the unit exhibits a distinct change in performance.

7. Replacement parts - If replacement parts are required, the service technician must use

only replacement parts that are specified by the manufacturer. Unauthorized

replacements may result in fire, electrical shock or other hazards.

8. Safety check - Upon completion of service or repair work on the unit, ask the service

technician to perform safety checks to ensure that the unit operates properly

9. Power sources - Operate the unit only from the type of power source indicated on the

label. If unsure of the type of power supply to use, contact your dealer

10. Lightning - For added protection during electrical storms external lightning conductors

can be installed. This prevents power surges from damaging the unit.

11. The units should be installed in locations with restricted access.

AMC2 Modular Controller Safety Instructions | en 5

Bosch Access Systems GmbH Installation Manual 2018-02 | AMC2-4R4 |

1.2 Safety Precautions

Read instructions!

Before working with the AMC2 device, read these instructions carefully. Make sure you have

understood all information described in this document.

Warning!

Risk of electric shock

External power supplies must be installed and put into service by qualified personnel.

Ensure compliance with the relevant regulations.

Ground the controller.

Disconnect both AC and battery power supply before working on the controller.

Warning!

Risk of fire

Installation of the AMC2 device must comply with any local fire, health, and safety

regulations. A secured door that may be part of an escape route from an area must be

installed with:

Install a fail-safe lock (A), so that the door will be released if power fails. Ideally, use a

magnetic lock.

Install a normally-closed break glass or a manual pull (B) in the lock supply wiring, so that in

an emergency the fail-safe lock can be immediately powered down.

Warning!

Risk of explosion of Lithium battery

The battery can explode if it is replaced incorrectly.

Replace only with the same type as recommended by the manufacturer.

Dispose used batteries according to the battery manufacturer’s instructions.

Notice!

Risk of damage to equipment

Protect the hardware from electrostatic discharge by observing ESD instructions before

unpacking of touching connectors of electronics.

Always switch off power of the AMC2 device before modifying the installation.

Do not connect or disconnect plug connectors, data cables, or screw connectors while power

is on.

Rules and Conditions

There are no specific requirements as for selling and delivery. As for storage and safe

operation, the environmental temperature should not exceed the range of 0°C to 50°C.

Disposal

Your Bosch product is designed and manufactured with high-quality materials and

components which can be recycled and reused.

This symbol means that electrical and electronic equipment, at their end-of-life, should be

disposed of separately from your household waste.

6en | Safety Instructions AMC2 Modular Controller

2018-02 | AMC2-4R4 | Installation Manual Bosch Access Systems GmbH

In the European Union, there are separate collection systems for used electrical and electronic

products. Please dispose of this equipment at your local community waste collection/recycling

center.

1.3 Unpacking

Check the packaging for visible damage. If anything has been damaged during transport,

please inform the transport agency.

Unpack the unit carefully. This is an electronic device that must be handled with care to avoid

damage. Do not attempt to put the unit into operation if components are damaged.

If any parts are missing, inform your customer service representative or a Bosch Security

Systems salesperson. The shipping carton is the safest transport container for the unit. Store

it and the other packaging material for future use. If the unit has to be sent back, use the

original packaging.

AMC2 Modular Controller Important Information | en 7

Bosch Access Systems GmbH Installation Manual 2018-02 | AMC2-4R4 |

2 Important Information

Remarks

This hardware is part of a security system. Access should be limited to authorized persons

only.

Some states do not allow the exclusion or limitation of implied warranties, or limitation of

liability for incidental or consequential damages, hence the above limitation or exclusion might

not apply to you.

Bosch Security Systems retains all rights not expressly granted. Nothing in this license

constitutes a waiver of Bosch’s rights under the U.S. Copyright laws or any other federal or

state law.

If you have any questions concerning this license, please, write to:

Bosch Sicherheitssysteme GmbH

Robert-Bosch-Ring 5

85630 Grasbrunn

Germany.

2.1 Explanation of symbols in this document

Throughout this document, warning messages, important notes, and helpful tips are presented

for the reader. These appear as follows:

Danger!

Cause of Hazard

Indicates a hazardous situation, which, if not avoided, will result in death or serious injury.

Warning!

Cause of Hazard

Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.

Caution!

Cause of Hazard

Indicates a hazardous situation, which, if not avoided, could result in minor or moderate

injury.

Notice!

Cause of Hazard

Important Notes that must be followed to avoid damage to the equipment or environment,

and to ensure successful operation and programming.

Tips and shortcuts may also be included in such notes.

2.2 Internet

If you are interested in further information on this product or information on other products,

please consult our website at http://www.boschsecurity.com.

8en | Introduction AMC2 Modular Controller

2018-02 | AMC2-4R4 | Installation Manual Bosch Access Systems GmbH

3 Introduction

3.1 Description

The APC-AMC2-4R4CF (also called AMC2-4R4, AMC2, or controller) is equipped with four

independent interfaces for RS-485 type readers. It is able to control up to four doors with a

reader in each direction and up to eight doors with a reader in one direction only.

Figure3.1: The Access Modular Controller AMC2-4R4

All necessary information for access verification is stored in a battery buffered on-board

memory and a Compact Flash (CF) memory card. This guarantees autonomous access

decisions and complete access registrations even if the management host system is offline.

The built in compact flash card provides adequate storage capability for cardholders and

events.

The AMC2-4R4 electronics are completely covered by a plastic housing. The liquid crystal

display provides all important status information.

Using the AMC2-4R4 gives you the full functionality and the offline capability of a complete

access control system in each room. This leads to an excellent reliability and a very high

redundancy without extra cost.

Figure3.2: The AMC2-4R4 in a four door safety lock

The AMC2-4R4 can communicate upstream to the host computer using RS-485 multi‑dropped,

RS-232 or 10/100 Mbit/s Ethernet. It has eight analog input devices and eight relay outputs.

With its analog input devices, the AMC2-4R4 verifies, for example, if a lock is closed or open.

The relay outputs can be used to activate lock mechanisms if access is granted, or activate the

AMC2 Modular Controller Introduction | en 9

Bosch Access Systems GmbH Installation Manual 2018-02 | AMC2-4R4 |

burglar alarm system if an intrusion or system alert is detected. If the eight inputs and eight

outputs on board are not enough to configure the system, up to three additional extensions

(AMC2-8IOE, AMC2-16IE, or AMC2-16IOE) can be connected. The extensions offer 8 or 16

additional inputs and outputs.

The setup procedure for an AMC2-4R4 is made very simple and fast by the use of door

templates. Once selected, all the inputs and outputs are predefined. These settings can be

changed to choose every free contact of the controller or a connected extension.

3.2 Equipment Configuration

Figure3.3: Upper circuit board with display (top side)

1(N.A.)

2DIL switch for RS-485 address selection , protocol, and RS-232/RS-485 selection.

3Lithium battery for buffering of static RAM and real time clock (RTC). The battery life

is estimated at 10 years, nevertheless an error message is generated if the voltage

sinks below a preset minimum level.

NOTICE: In order to avoid an error message caused by an earlier voltage drop we

suggest to replace the battery every 8 years. Spare part: VARTA CR 2032 PCB.

4Reset push button - reachable through the casing using a screwdriver

5Liquid Crystal Display

6Push button, available on top of the housing, to select different display modes

7Jumper: Equalization of potential between different systems and earth ground

(shield)

8Jumper: Interface selector RS-485 host connection, RS-485 two wire or RS-485 four

wire (depends on external wiring)

9Configurable RS-485 host interface

10 Docking port for compact flash memory

11 Configurable RS-232 host interface (ribbon cable connector)

12 Configurable 10/100 Mbit/s Ethernet host interface

10 en | Introduction AMC2 Modular Controller

2018-02 | AMC2-4R4 | Installation Manual Bosch Access Systems GmbH

Figure3.4: Overview - Interfaces

13 RS-485 extension module bus

14 External tamper contact

15 Connector for power supply

16 RS-485 interfaces for up to 8 card readers

17 Connectors for eight analog inputs

18 Connectors for eight relay outputs

Notice!

All connectors, with the exception of the RS-232 and Ethernet host interface, are pluggable

screw clamp terminals.

Figure3.5: Jumper at the bottom side

Andere Handbücher für AMC2 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bosch Controller Handbücher

Bosch

Bosch Readykey K6199-CNCii Gebrauchs- und Pflegehandbuch

Bosch

Bosch K 30 RF Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl L25 Bedienungsanleitung

Bosch

Bosch CS 550 Bedienungsanleitung

Bosch

Bosch G100 Bedienungsanleitung

Bosch

Bosch AVENAR panel 8000 Bedienungsanleitung

Bosch

Bosch Rexroth CKL Series Leitfaden

Bosch

Bosch Rexroth VT-HNC100 3X/S Series Gebrauchsanweisung

Bosch

Bosch ADS?AMC2?2WCF Bedienungsanleitung

Bosch

Bosch APC-AMC2-4R4CF Bedienungsanleitung

Bosch

Bosch REG 73-1 Bedienungsanleitung

Bosch

Bosch rexroth SB11 Bedienungsanleitung

Bosch

Bosch rexroth ctrlX CORE Bedienungsanleitung

Bosch

Bosch EasyControl CT200 Bedienungsanleitung

Bosch

Bosch PVA-4CR12 Bedienungsanleitung

Bosch

Bosch RC35 Kurzanleitung

Bosch

Bosch Twist Bedienungsanleitung

Bosch

Bosch rexroth CytroForce-M Bedienungsanleitung

Bosch

Bosch BAT 250 Bedienungsanleitung

Bosch

Bosch WORCESTER GREENSTAR WIRING CENTRE Benutzerhandbuch

Bosch

Bosch DSA E Series Bedienungsanleitung

Bosch

Bosch PXI-CORE Edge controller Bedienungsanleitung

Bosch

Bosch CR 10 Bedienungsanleitung

Bosch

Bosch Rexroth IndraMotion MTX micro Produktinformationsblatt

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch