Bosch e103022 Bedienungsanleitung
Installation Instructions
Notice d’installation
Instrucciones de instalación
9001117065 (9511)
To avoid possible injury or property damage, OBSERVE ALL WARNINGS
AND CAUTIONS.
These instructions are intended for use by qualied installers only. The
dishwasher must be installed by a qualied service technician or installer.
• In addition to these instructions, the dishwasher shall be installed to
meet all electrical and plumbing codes and ordinances (both national
and local).
Read these installation instructions completely and follow them
carefully. They will save you time and effort and help to ensure safety and
optimum dishwasher performance.
IMPORTANT
• The dishwasher drain hose must be installed with a portion of it at least
20″ (508 mm) off the cabinet oor; otherwise the dishwasher may not
drain properly.
• This dishwasher is intended for indoor residential use only, and should
not be used in commercial food service establishments.
• This dishwasher is designed to be enclosed on the top and both sides
by cabinetry.
• NEW INSTALLATION - If the dishwasher is a new installation, ensure
all connections are properly made before the dishwasher is moved into
place.
• REPLACEMENT - If the dishwasher is replacing another dishwasher,
check the existing dishwasher connections for compatibility with the
new dishwasher, and replace parts as necessary.
• This appliance has been found to be in compliance with CAN/CSA-C22.2
No. 167/UL 749. It is the responsibility of the owner and the installer
to determine if additional requirements and standards apply in specic
installations.
• Not for outdoor use.
1
Important Safety Instructions:
Please READ and SAVE this information
2
Avoiding General Hazards
Do not use the dishwasher until it is completely installed. When opening
the door on an uninstalled dishwasher, carefully open the door while
supporting the rear of the unit. Failure to follow this warning can cause the
dishwasher to tip over and result in serious injury.
Before installing the “L”-shaped supplied countertop mounting brackets
(select models), decide which method will be used to secure the dish-
washer into its opening. Once these mounting brackets are installed on
the dishwasher, removing them is difcult and will damage the mounting
brackets and the dishwasher.
In some conditions, hydrogen gas can form in a hot water system that
has not been used for weeks. Hydrogen gas is explosive. Before lling a
dishwasher from a system that has been off for weeks, run the water from
a nearby faucet in a well ventilated area until there is no sound or evidence
of gas.
Temperatures required for soldering and sweating will damage the
dishwasher’s base and water inlet valve. If plumbing lines are to be
soldered or sweated, keep the heat source at least 6 inches (152.4 mm)
away from the dishwasher’s base and water inlet valve.
Removing any cover or pulling the dishwasher from the cabinet can
expose hot water connections, electrical power and sharp edges or points.
Handle with care.
Avoiding Electrical Shock/Fire Hazards
Do not allow the electrical and water supply lines to touch.
Do not work on an energized circuit. Doing so could result in serious
injury or death. Only qualied electricians should perform electrical work.
Do not attempt any work on the dishwasher electric supply circuit until
you are certain the circuit is de-energized.
Make sure electrical work is properly installed. There should be no loose
electrical connections. Ensure all electrical connections are properly
made.
WARNING
The customer has the responsibility of ensuring that the dishwasher
electrical installation is in compliance with all national and local electrical
codes and ordinances. The dishwasher is designed for an electrical supply
of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly
grounded electrical circuit with a fuse or breaker rated for 15 amps.
Electrical supply conductors shall be a minimum #14 AWG copper only
wire rated at 75°C (167°F) or higher.
This appliance must be connected to a grounded metal, permanent wiring
system, or an equipment-grounding conductor must be run with the circuit
conductors and connected to the equipment-grounding terminal or lead on
the appliance. Do not use extension cords.
Avoiding Plumbing/Scalding Hazards
Do not perform any work on a charged hot water line. Serious injury could
result. Only a qualied plumber should perform plumbing work. Do not
attempt any work on the dishwasher hot water supply plumbing until you
are certain the hot water supply is shut off.
Do not over tighten the 90° elbow. Doing so may damage the water inlet
valve and cause a water leak.
Check local plumbing codes for approved plumbing procedures and ac-
cessories. All plumbing should be done in accordance with national and
local codes.
These instructions depict an installation method for stainless steel braided
hose or PEX hot water supply lines. If using copper tubing or other material
for water supply, defer to a licensed plumber for proper installation.
3
Materials Supplied (all models)
4
E
F
G
D
K
L
B
A
H
I
J
C
Inspect the Dishwasher
After unpacking the dishwasher and prior to installation, thoroughly inspect
the dishwasher for possible freight or cosmetic damage. Report any
damage immediately. Cosmetic defects must be reported within 30 days
of installation.
NOTE: Do not discard any bags or items that come with the original package
until after the entire installation has been completed.
Materials Supplied (model dependent)
NOTE: Same
as Material “D”.
5
Materials Needed
Hot Water Supply Line - Minimum
3/8” O.D. copper tubing, PEX, or
metal braided dishwasher supply line.
Electrical Supply Cable - Minimum #14
AWG, 2 conductor, 1 ground, insulated
copper conductors rated 75°C (167°F) or
higher.
Shut-off Valve and ttings appropriate
for hot water supply line (copper tubing/
compression tting, or braided hose).
90° elbow with 3/4” N.P.T. female
threads on one leg, and sized to t your
water supply line (copper tubing/com-
pression tting, or braided hose) on the
other leg.
UL listed conduit connector or strain
relief.
Tools Needed
6
IMPORTANT!
Before you begin, you must read the safety instructions.
PRE-INSTALL CHECKLIST
� Unpack unit. Retain packing material until successful installation is
complete.
� Remove all packing material from inside the dishwasher.
� Inspect parts to ensure you have all the necessary materials.
� Flush household hot water supply for at least two minutes.
� Measure the enclosure area.
� Is the opening at least 34" (863.6 mm) high and 24" (609.6 mm) wide?
� Is the opening near enough to the sink for the water line and drain
hoses to access plumbing?
� Will the unit be installed close enough to the sink so that drain hose
length does not exceed 92" (2336.8 mm) and so that a portion of the
drain hose is raised at least 20" (508 mm) above the oor?
� Do the openings for electric cable, water line, and drain hose routing
through cabinet t within the shaded area in Figure 1?
� Are the openings sanded smooth if wood or covered by a protective
gasket if metal?
� Is your water heater set at 120°F (49°C) and does water pressure
measure 15-145 psi (1-10 bar)?
� If installing in a corner, will the dishwasher door clear cabinet
hardware?
� Determine mounting method based on dishwasher model and
countertop type (see Figures 6-8, 20).
� Only use included hardware for install. If replacing dishwasher,
dispose of old hose and other equipment properly.
7
24" (600 mm) with side
strips removed.
Minimum hole size for drain
hose is 1 1/2" (38.1 mm).
Minimum hole size if drain
hose and inlet hose are
through same hole is 2"
(50.8 mm).
Remove the toe panel(s) (Part H or Parts I and J depending on model) (1)
from the unit and retain for attachment to the front at a later time. Loosen
the leg levelers slightly. Remove junction box cover and retain for later use
(2). Discard the small piece of protective styrofoam.
4" (102 mm)
2" (51 mm)
24 - 24
1/4
" (610-616 mm)*
90°
24" (610 mm)
33
7/8
" (86 cm) min
1
1
2
2
8
Inhaltsverzeichnis
Sprachen:
Andere Bosch Spülmaschine Handbücher
Bosch
Bosch SHV89PW53N Bedienungsanleitung
Bosch
Bosch SMS4HTW33E Technisches Datenblatt
Bosch
Bosch SMU2ITS01A Bedienungsanleitung
Bosch
Bosch SGV68U53UC Bedienungsanleitung
Bosch
Bosch SGE78B55UC Bedienungsanleitung
Bosch
Bosch SMS4EKI00E Technisches Datenblatt
Bosch
Bosch diswacher Bedienungsanleitung
Bosch
Bosch SHE53T55UC Betriebsanleitung
Bosch
Bosch SHU 4300 series Bedienungsanleitung
Bosch
Bosch SN61HX04AE Technisches Datenblatt
Bosch
Bosch SMU8EDS01A Bedienungsanleitung
Bosch
Bosch SMS4EKW02E Technisches Datenblatt
Bosch
Bosch SMS4EMI02E Technisches Datenblatt
Bosch
Bosch SBH4HVX31G Bedienungsanleitung
Bosch
Bosch Ascenta SHE3AR52UC Bedienungsanleitung
Bosch
Bosch SBV4HTX33E Bedienungsanleitung
Bosch
Bosch SMS2HTI60E Bedienungsanleitung
Bosch
Bosch SMV69T20GB Bedienungsanleitung
Bosch
Bosch SMS4ETI02E Technisches Datenblatt
Bosch
Bosch SBH4HCX48E Technisches Datenblatt
