Bosch HMV9302 Bedienungsanleitung

Household Appliances

Over-the-Range Microwave

Installation Instructions

For Models: HMV9302, HMV9303, HMV9305, HMV9306, HMV9307

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING

IMPORTANT: Save these instructions for the local electrical inspector’s use.

INSTALLER: Please leave these Installation Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

Printed in Korea

P/No.: 3828W5U0503

YOUR SAFETY FIRST

BEFORE YOU START

• Proper installation is the installer's responsibility!

– Read the entire manual before you begin. The Model number label is located on the oven front. See Figure 1.

Mounting plate is located on back side of microwave oven. See Figure 2.

BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:

FOR YOUR SAFETY:

• You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled properly.

The dimensions of the oven are as follows:

Height : 16 7/16 inches

Width : 29 15/16 inches

Depth : 15 5/8inches

Weight : 60 lbs.

• Avoid Electrical Shock!

– Before you drill into the wall, note where electrical outlets are and where electrical wires might be concealed

behind the wall. YOU COULD GET AN ELECTRIC SHOCK if you contact electrical wires with your drill bit.

– Locate and disconnect the power to any electrical circuits that could be affected by installing this oven.

IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.

• ELECTRICAL RATING OF THIS OVEN : 120V AC 60Hz.

– You need a DEDICATED 120V, 60Hz, AC only, 15 or 20A, fused electrical supply (located in the cabinet above

the microwave as close as possible to the microwave) serving only the microwave.

Mounting

plate

( Remove from

oven to install. )

Back of oven

Figure 1 Figure 2

Model Number Label

WARNING

• THIS APPLIANCE MUST BE GROUNDED!

–If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire

for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug.

• Place the plug into a properly installed and grounded outlet. See Figure 3.

• Do not use an extension cord.

• Keep the power cord dry and do not pinch or crush it.

• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE

POWER SUPPLY CORD GROUNDING PRONG!

This appliance MUST be grounded!

If you use the grounding plug improperly, you risk electric shock!

–Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do not

completely understand the grounding instructions.

DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.

Improper grounding could result in electric shock or other personal injury.

SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

• DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!

–DO NOT try to operate the microwave oven with the door open.

–DO NOT tamper with or defeat the safety interlocks.

–DO NOT place objects between the microwave oven front face and the door.

–

DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.

–DO NOT operate the microwave oven if it is damaged.

–The microwave oven door must close properly to operate safely.

–DO NOT USE THE MICROWAVE OVEN:

• If the door is bent.

• If the hinges or latches are broken or loose.

• If the door sealing surfaces or glass is broken or cracked.

–DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF!

It should be adjusted and repaired by a qualified technician who can check for microwave leakage after

repairing the oven.

If you do not use the microwave oven as instructed,

you could be exposed to excessive microwave energy.

YOUR SAFETY FIRST

PROPERLY POLARIZED AND

GROUNDED OUTLET

Three-Pronged (Grounding) Plug

Figure 3

WARNING

• MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.

–Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of

minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.

–ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.

–DO NOT mount the microwave oven to an island or peninsula cabinet.

–BE SURE the upper cabinet and rear wall structures are able to support 150 lbs., plus the weight of any items

you place inside the oven or upper cabinet.

–Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.

–BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.

If you do not mount the oven as instructed,

you risk personal injury and/or property damage.

CAUTION

• Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY

MATERIAL (such as a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.

Failure to protect these surfaces could result in property damage.

YOUR SAFETY FIRST

30" min. cabinet opening width

30" min. clearance from bottom

of cabinet to cooking surface

or countertop

(Use templates included

with installation instructions)

Grounded Outlet

(inside upper cabinet)

Power Supply Cord Hole

Figure 4

CAUTION

THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:

PARTS, TOOLS, MATERIALS

Damper/duct connector

(for roof vented or wall vented installation)

Not Actual Size

Four 1/4" x 2" lag screws - Actual Size

(for wall stud holes)

Four 1/4" x 3" toggle bolts - Actual Size

(for drywall holes)

Two 1/4" x 3" bolts - Actual Size

(for securing to the upper cabinet)

Four spring toggle heads - Actual Size

(for the toggle bolts)

Left side

Right side

centerline

12"

10-

Roof-ventinginstallation

Upper-cabinettemplate

10-

316

One upper cabinet template - Not Actual

Size

Two tapping screws - Actual Size

(for attaching the damper duct connector)

One power cord clamp bushing - Actual Size (for the cord hole in a metal upper cabinet)

One power cord clamp and

One dark-colored mounting screw

(to hold the power cord)

Actual Size

NOTE: Depending on your ventilation requirements, you may not use all of these parts.

NOTE: You need to install at least one lag screw into a 2" x 4" stud and four anchor bolts into the wall,

and the mounting area must meet the 150 lbs. weight requirement.

YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION:

Carton or other heavy material for covering the counter top.

• If you have brick or masonry walls, you will need special hardware and tools.

• The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft damper

(shown on page 5).

PARTS, TOOLS, MATERIALS

Clear tape

(for taping the templates to the wall) Stud finder or thin nail.

Saber saw (for cutting vent

holes for roof or wall venting)

Keyhole saw (for the power cord hole)

Electric drill

3/8" and 3/4" wood drill bits

1/2" and 3/16"

drill bits

Phillips screwdriver

Pencil

Flat blade screwdriver

Measuring tape (metal preferred)

Small side cutters or tin snips Caulking gun

Plumb line

Duct Tape

Gloves

AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED!

1. Locate the grounded electric outlet for this oven in the cabinet

above the oven, as shown in Figure 4 Detail.

2. You will cut the power-supply-cord hole (shown in Figure 4 Detail)

later when you prepare the wall and upper cabinet in Step 4.

Improper grounding could result in

electric shock or other personal injury.

• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY

CORD GROUNDING PRONG! This appliance MUST be grounded!

STEP 1: PREPARE THE

ELECTRICAL CONNECTIONS

Grounded Outlet

( Inside Cabinet )

Upper

Cabinet

Power-Supply-Cord Hole

Figure 4 Detail

WARNING

NOTE: The outlet should be on a circuit dedicated to the

microwave oven 120V, 60Hz., AC only with a 15 or

20A fused electrical supply.

NOTE: Do not use an extension cord.

Keep the power cord dry and do not pinch or crush it.

IMPORTANT: If you do not have the proper wall outlet, you

MUST have one installed by a qualified

electrician.

THIS OVEN MUST BE PROPERLY VENTED!

You may vent your oven in one of three ways:

Roof-venting If your oven is located on an outside wall near the roof, as in Figures 5 (31/4" x 10" duct)

and 6 (6" round duct.)

Wall-venting If your oven is located on an outside wall on the first floor of your house, as in Figure 7

(31/4" x 10" duct) and Figure 6 (6" round duct.)

Room-venting If your oven is located on an inside wall of your house, as in Figure 8.

REMEMBER AS YOU INSTALL THE VENTING:

• Keep the length of the ductwork and the number of elbows to a minimum to ventilate your oven efficiently.

See examples on page 9.

• Keep the size of the ductwork the same.

• Do not install two elbows together.

• Use duct tape to seal all joints in the duct system.

• Use caulking to seal the exterior wall or roof opening around the cap.

STEP 2:

PREPARE THE VENTING SYSTEM

Wall-venting

through-the-wall

wall cap

3 1/4"x10"

duct

Figure 7

cabinet

oven

through-the-roof

3 1/4"x10"

duct

Figure 5

roof cap

Roof-venting

cabinet

oven

6" min.

diameter

round duct

3 1/4" to round

duct transition

3 1/4" to round

ductwork transition

Figure 6

roof cap

wall cap

elbow

WARNING:FIRE HAZARD

room-venting

Figure 8

cabinet

oven

NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork

fittings and length are shown in Figure 9, page 9.

NOTE: If you choose the rear exhaust method (roof- or wall-venting), be sure there is enough clearance within the

wall for the exhaust duct.

“wall-venting”

“roof-venting”

STEP 2:

PREPARE THE VENTING SYSYTEM

STANDARD FITTINGS

DUCT LENGTH

The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not

exceed the equivalent of 140 feet.

For best performance, do not use more than three 90 degree elbows.

Below are the standard fittings and their equivalent length in feet.

Figure 9

Examples

For 3 1/4"x10" SYSTEMS

1-3 1/4" x 10" 90oelbow

1-Wall Cap

8 feet straight duct

TOTAL LENGTH

1-transition

2-90oelbows

1-Wall Cap

8 feet straight

TOTAL LENGTH

For 6" ROUND SYSTEMS

4567

3 1/4"x10"

to 6"=5ft.

90oelbow

=10ft.

45oelbow

=5ft.

3 1/4"x10"

wall cap

=40ft.

3 1/4"x10"

flat elbow

=10ft.

3 1/4"x10" roof

cap=24ft.

3 1/4"x10" 90˚

elbow=25ft.

6ft.

2ft. 2ft.

3 1/4"x10"

90oelbow

wall cap

6ft.

90oelbows

transition

wall cap

= 25 ft.

= 40 ft.

= 8 ft.

= 73 ft.

= 5 ft.

= 20 ft.

= 40 ft.

= 8 ft.

= 73 ft.

NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension

duct installed between the damper assembly and the adapter to prevent the exhaust damper’s sticking.

To calculate the equivalent length of each ductpiece used, see the examples below.

Your microwave oven is shipped with the blower assembled for roof venting. You need to adjust the blower if

you want wall-venting or room-vented (recirculating) installation.

ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT.

•DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in

electrical shock.

REMOVE THE MOUNTING PLATE:

1. Remove any shipping materials and parts from inside

the microwave oven.

2. Cover the countertop or cooktop with a thick,

protective covering to protect it from damage and dirt.

See Figure 10.

3. Remove mounting plate screw(s) (1 or 2 screws)

from the mounting plate as shown and discard

(see Figure 11).

4. This plate will be used to locate and mark the mounting

holes on the rear wall. (It will be used to locate and

mark the mounting holes on the rear wall.)

5. Locate exhaust adaptor, grease filters and hardware

packet.

6. At this point, remove any adhesive tape (if there is any),

on the exhaust adaptor, the grease filters and the

power supply cord.

ROOF-VENTED INSTALLATION:

This oven is shipped assembled for roof-vented. You

will need to install the exhaust adaptor regardless of

cabinet.

1. Attach the exhaust adaptor to the blower plate by

sliding it into the guides (see Figure 12).

Go to step 4 on page 13.

STEP 3:

PREPARE THE VENTING BLOWER

Figure 10

A thick, protective

covering

Figure 11

Mounting

plate

Mounting plate

screw(s)

(1 or 2 screws)

Control panel side

Figure 12

Back

of oven

Exhaust

adaptor

WARNING

NOTE: If you have a free-standing range, disconnect it, move it

onto a piece of cardboard or hardboard and pull it away

from the wall, so that you can get closer to the upper

cabinet and back wall for easier measuring and drilling.

Andere Handbücher für HMV9302

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Bosch Mikrowellenofen Handbücher

Bosch

Bosch HMT84G651B Bedienungsanleitung

Bosch

Bosch HMT75G451B Bedienungsanleitung

Bosch

Bosch CMA585GS0B Bedienungsanleitung

Bosch

Bosch BFL554MB0 Bedienungsanleitung

Bosch

Bosch HBC86K7.0 Bedienungsanleitung

Bosch

Bosch HMB57152UC Bedienungsanleitung

Bosch

Bosch HBC84H500 Bedienungsanleitung

Bosch

Bosch HMT84M624B Bedienungsanleitung

Bosch

Bosch FFL023MW0 Bedienungsanleitung

Bosch

Bosch HMT84G651V Bedienungsanleitung

Bosch

Bosch HMB45C453X Bedienungsanleitung

Bosch

Bosch HMD8451UC/02 Bedienungsanleitung

Bosch

Bosch HMC80251UC Bedienungsanleitung

Bosch

Bosch HMV3051U - 300 Series - Microwave Bedienungsanleitung

Bosch

Bosch BEL554MS0T Bedienungsanleitung

Bosch

Bosch HMB402 Bedienungsanleitung

Bosch

Bosch HMV 8051 U Bedienungsanleitung

Bosch

Bosch CMA585MS0I Bedienungsanleitung

Bosch

Bosch FEL023MS1 Bedienungsanleitung

Bosch

Bosch CMA583MS0B Bedienungsanleitung

Bosch

Bosch HMV5051U Bedienungsanleitung

Bosch

Bosch HMV3051U - 300 Series - Microwave Bedienungsanleitung

Bosch

Bosch HMVP053U Bedienungsanleitung

Bosch

Bosch HMV9302 Bedienungsanleitung

Beliebte Mikrowellenofen Handbücher anderer Marken

Daewoo

Daewoo KOG-574R0S Bedienungsanleitung

LG MH7040SS Bedienungsanleitung

Sharp

Sharp R-895(AL)M Bedienungsanleitung

Dometic

Dometic DOTRM13W Bedienungsanleitung

Sanyo

Sanyo EM-X680 Bedienungsanleitung

Sharp

Sharp R-393M Bedienungsanleitung

KitchenAid

KitchenAid KMCX4510 Montageanleitung

Smeg

Smeg S45MCX1 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHM2044 Bedienungsanleitung

Sunbeam

Sunbeam SMW759 Bedienungsanleitung

Gallet

Gallet FMOE230S Bedienungsanleitung

Dometic

Dometic Roadmate 230 Bedienungsanleitung

Samsung

Samsung SJ0396W Bedienungsanleitung

Sanyo

Sanyo EM-P494WS Bedienungsanleitung

Sharp

Sharp R-240 Bedienungsanleitung

Electrolux

Electrolux EMS2840 Bedienungsanleitung

Daewoo

Daewoo KOC-984T2S13 Bedienungsanleitung

Impecca

Impecca CM07M2 Bedienungsanleitung