Bosch B450 Original Betriebsanleitung

Conettix Plug-in Communicator Interface

B450

en Installation and Operation Guide

Table of contents

1Safety 4

2Introduction 5

2.1 About documentation 5

2.2 Bosch Security Systems, Inc. product manufacturing dates 5

2.3 Installation workflow 5

3System overview 7

3.1 Module overview 7

3.2 Bus address settings 8

4Installation 10

4.1 Setting the bus address 10

4.2 Insert the B44x communication module (required and available separately) 10

4.3 Mount the module in the enclosure 11

4.3.1 Mount and wire the tamper switch (option for SDI2 bus only) 12

4.4 Install and mount the plug-in communicator antenna 12

4.5 Wire to the control panel 13

4.5.1 Wire to an SDI2 control panel 14

4.5.2 Wire to an SDI control panel 15

4.5.3 Wire to an option bus control panel 16

5Configuration 17

5.1 Plug and Play configuration 17

5.2 Configuration for SDI2 control panels 17

5.2.1 Configuring and viewing status from RPS 17

5.3 Use USB to configure the B450 22

5.3.1 Install a communication program 24

5.3.2 Log into the USB interface 25

5.3.3 USB Main menu 27

5.3.4 USB menu structure 27

5.3.5 USB menu 28

5.4 Short Message Service (SMS) configuration 32

5.4.1 Use SMS to configure the B450 32

5.5 Firmware Update page 35

6Maintenance and troubleshooting 39

6.1 LED status indicators 39

6.2 Show the firmware version 41

6.3 Diagnostic log 41

6.4 Understanding network polling 41

6.4.1 Example 1 - High Security Application 42

6.4.2 Example 2 - Medium Security Application 42

6.4.3 Example 3 - Backup or Low Security Application 42

6.5 Control panel programming using cellular 43

7Specifictions and certifications 44

7.1 Technical specification 44

7.2 Certifications 45

Conettix Plug-in Communicator

Interface Table of Contents | en 3

Bosch Security Systems, Inc. Installation and Operation Guide 2013.09 | 02 | F.01U.282.875

Safety

ESD Precaution

Please note that while the B450 comes in a plastic case, and is protected from ESD, the plug-

in cellular communicator (B44x) does not. All plug-in cellular communicator components may

potentially be exposed to finger touches - therefore extra attention must be paid to ESD

(electrostatic discharge) precaution. Make sure there is no static interference when using the

board. Appropriate ESD protections must be taken and wearing electrostatic equipment is

recommended, such as anti-static wrist strap.

ESD damage can range from subtle performance degradation to complete device failure.

Precision integrated circuits may be more susceptible to damage because very small

parametric changes could cause the device not to meet its published specifications.

Warning!

Failure to follow these instructions can result in a failure to initiate alarm conditions. Bosch

Security Systems, Inc. is not responsible for improperly installed, tested, or maintained

devices. Follow these instructions to avoid personal injury and damage to the equipment.

Notice!

Inform the operator and the local authority having jurisdiction (AHJ) before installing the

module in an existing system.

Disconnect all power to the control panel before installing the module.

4en | Safety Conettix Plug-in Communicator

Interface

2013.09 | 02 | F.01U.282.875 Installation and Operation Guide Bosch Security Systems, Inc.

Introduction

About documentation

This document is the intellectual property of Bosch Security Systems, Inc. and is protected by

Trademarks

All hardware and software product names used in this document are likely to be registered

trademarks and must be treated accordingly.

Bosch Security Systems, Inc. product manufacturing dates

Use the serial number located on the product label and refer to the Bosch Security Systems,

Inc. website at http://www.boschsecurity.com/datecodes/.

The following image shows an example of a product label and highlights where to find the

manufacturing date within the serial number.

Installation workflow

To install and configure the device, use the workflow below and follow in sequential order

from top to bottom, marking off each box as you complete a step.

Caution!

Always power down the control panel when connecting the B450. Power down the control

panel by unplugging the transformer and disconnecting the battery.

Plan the installation of the B450 Conettix Plug-in Communicator Interface

Unpack the device contents

Power down the system

Select the bus address value for the compatible control panel (This will automatically

configure the module to work with a compatible control panel. Refer to Setting the bus

address, page 10)

Insert the desired plug-in communicator into the B450 (Refer to Insert the B44x

communication module (required and available separately), page 10)

Mount the B450 into the enclosure (Refer to Mount the module in the enclosure, page 11)

Wire the B450 to a compatible control panel (Refer to Wire to the control panel, page 13)

Power up the system

2.1

2.2

2.3

Conettix Plug-in Communicator

Interface Introduction | en 5

Bosch Security Systems, Inc. Installation and Operation Guide 2013.09 | 02 | F.01U.282.875

Install a communication program (if required) (Refer to Install a communication program,

page 24)

Configure the communication module (non SDI2 control panels)

Verify LED activity

Review signal strength on the cellular communicator. Refer to your cellular communicator

Installation Guide for more information on signal strength.

Installation is complete

See also

–Configuration, page 17

–Maintenance and troubleshooting, page 39

6en | Introduction Conettix Plug-in Communicator

Interface

2013.09 | 02 | F.01U.282.875 Installation and Operation Guide Bosch Security Systems, Inc.

System overview

Refer to the graphic below for the complete B450 system configuration.

B450 system connections overview

Callout ᅳ Description Callout ᅳ Description

1 ᅳ Compatible Bosch control panel 6 ᅳ Cellular carrier network

2 ᅳ Panel data bus (SDI2 , SDI, or Option) 7 ᅳ Internet/LAN/WAN

3 ᅳ B450 8 ᅳ Remote Programming Workstation

4 ᅳ USB direct connection for B450

configuration (if required)

9 ᅳ Bosch Conettix IP receiver (D6600,

D6100i, or D6100IPv6)

5 ᅳ B44x Plug-in Cellular Communicator

(required and available separately)

Module overview

The B450 Conettix Plug-in Communicator Interface (wired to a compatible control panel) is a

four-wire powered SDI2, or SDI device that provides two-way communication over commercial

cellular networks using a plug-in communicator.

The B450 Conettix Plug-in Communicator Interface bus address switch determines the bus

address of the device. When required, configuration of the module is managed through the

control panel, a local USB connection, or using SMS.

3.1

Conettix Plug-in Communicator

Interface System overview | en 7

Bosch Security Systems, Inc. Installation and Operation Guide 2013.09 | 02 | F.01U.282.875

B450 module overview

862

754

TX RX

Figure 3.1: B450 Plug-in Communicator Interface

Callout ￚ Description

1 ￚ Tamper switch connector

2 ￚ Bus address switch

3 ￚ MODE 2-pin jumper connector (for future use)

4 ￚ Bus address label

5 ￚ USB connector (Type A)

6 ￚ Heartbeat LED

7 ￚ RX LED (indicates packets received from the wireless network)

8 ￚ TX LED (indicates packets transmitted over the wireless network)

9 ￚ Terminal strip (to control panel)

10 ￚ Interconnect wiring connectors (to control panel or other compatible modules)

Bus address settings

The address switch determines the bus address for the B450 Conettix Plug-in Communicator

Interface. The control panel uses the address for communications. Use a slotted screwdriver

to set the address switch.

Notice!

The B450 reads the bus address switch setting only during power up. If you change the

switch after you apply power to the module, you must cycle the power to the module in order

for the new bus address setting to be used for bus communication.

3.2

8en | System overview Conettix Plug-in Communicator

Interface

2013.09 | 02 | F.01U.282.875 Installation and Operation Guide Bosch Security Systems, Inc.

Bus address label

Use the bus address label to select the desired setting on the bus address switch, depending

on your control panel.

PANEL ADDRESSES

TX RX

0 1 2 4 5 6 7 8 9

Bus cfg 1 2 88 92 250

Addr SDI2 SDI Option

Figure 3.2: Bus address label

Conettix Plug-in Communicator

Interface System overview | en 9

Bosch Security Systems, Inc. Installation and Operation Guide 2013.09 | 02 | F.01U.282.875

Installation

Perform the following steps to install the B450.

Notice!

Remove all power (AC and Battery) before making any connections. Failure to do so may

result in personal injury and/or equipment damage.

Setting the bus address

The B450 Conettix Plug-in Communicator Interface address switch provides the value for the

module's address. The figure below shows the address switch setting for address 1. Refer to

the table below for panel-specific settings.

Figure 4.1: Address switch set to address 1

Control panels Switch

position

Control panel

bus address

Bus type Function

USB or SMS configuration

setting

0 N/A Any Change configuration

B5512/B4512/

B3512,D9412GV4/

D7412GV4/D7212GV4

1 1 SDI2 Automation, RPS, or Reporting

D9412GV4/D7412GV4/

D7212GV4

2 2 SDI2 Automation, RPS, or Reporting

D9412GV4/D7412GV4/

D7212GV4, D9412GV3/

D7412GV3/D7212GV3

4 88 SDI1RPS or Reporting

D9412GV4/D7412GV4/

D7212GV4, D9412GV3/

D7412GV3/D7212GV3

5 92 SDI1RPS or Reporting

1For D9412GV4/D7412GV4/D7212GV4 configurations, SDI2 bus connection is the recommended configuration

option, but SDI bus configuration is also supported.

Table 4.1: B450 address switch settings

Insert the B44x communication module (required and available

separately)

Insert the desired B44x communication module into the slot of the B450 until you feel the

module “click” into place.

4.1

4.2

10 en | Installation Conettix Plug-in Communicator

Interface

2013.09 | 02 | F.01U.282.875 Installation and Operation Guide Bosch Security Systems, Inc.

Andere Handbücher für B450

Inhaltsverzeichnis

Andere Bosch Aufnahmegeräte Handbücher

Bosch

Bosch FLM-420/4-CON-S Bedienungsanleitung

Bosch

Bosch Worcester Greenstar HIU E Bedienungsanleitung

Bosch

Bosch D8125MUX Betriebsanleitung

Bosch

Bosch TINYON IP 2000 WI Montageanleitung

Bosch

Bosch DIVAR IP 2000 DIP-2040EZ-00N Bedienungsanleitung

Bosch

Bosch FLM-420-O2-D Bedienungsanleitung

Bosch

Bosch DIVAR IP all-in-one 6000 Bedienungsanleitung

Bosch

Bosch DIVAR IP all-in-one 4000 Bedienungsanleitung

Bosch

Bosch DX4010V2 Bedienungsanleitung

Bosch

Bosch LBB 1968/00 Bedienungsanleitung

Bosch

Bosch DVR1A1081 Bedienungsanleitung

Bosch

Bosch CR 400 Bedienungsanleitung

Bosch

Bosch FLM-420-RHV-S Bedienungsanleitung

Bosch

Bosch FLM-420-O8I2-S Bedienungsanleitung

Bosch

Bosch MIC-ALM-WAS-24 Bedienungsanleitung

Bosch

Bosch FLM-420-NAC-S Bedienungsanleitung

Bosch

Bosch Divar 700 Series Bedienungsanleitung

Bosch

Bosch HPC 400 Bedienungsanleitung

Bosch

Bosch B450-M Bedienungsanleitung

Bosch

Bosch DIP-5042EZ-0HD Bedienungsanleitung

Bosch

Bosch Climate 5000 Series Bedienungsanleitung

Bosch

Bosch Rexroth IMenip Bedienungsanleitung

Bosch

Bosch DCN multimedia Bedienungsanleitung

Bosch

Bosch BRS Tower Montageanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch