Bosch FMR-1000-RCMD Betriebsanleitung

Remote Command Center

FMR-1000-RCMD

en Installation and Operation Guide

es Guía de Instalación y Operación

pt Manual de Instalação e Operação

FMR-1000-RCMD 3

Bosch Security Systems, Inc. F.01U.078.098 | 3.0 | 2011.11

en Installation and Operation Guide 5

es Guía de Instalación y Operación 17

pt Manual de Instalação e Operação 31

4FMR-1000-RCMD

F.01U.078.098 | 3.0 | 2011.11 Bosch Security Systems, Inc.

Remote Command Center Table of Contents | en 5

Bosch Security Systems, Inc. Installation and Operation Guide F.01U.078.098 | 3.0 | 2011.11

Table of Contents

1Notice 6

2 Scope of Delivery 6

3 Device Description 6

4Mounting 7

4.1 Removing the Cover Frame 7

4.2 Surface Mounting 7

4.3 Flush Mounting 8

5 Wiring 9

5.1 Option Bus Circuit Wiring Distance 9

5.2 Wiring Connections 9

5.3 Removing the Cover Frame for Service 10

6 Inserting the Language Tab 10

7 Address Setting 11

8Programming 11

9Operating 12

9.1 LEDs and LCD Keypad 12

9.2 Lamp Test 14

9.3 Keypad Operations 14

10 Troubleshooting 15

11 Specifications 15

11.1 Electrical 15

11.1.1 Wiring Specification 16

11.2 Mechanics 16

11.3 Environmental Conditions 16

11.4 Trademarks 16

6en | Notice Remote Command Center

F.01U.078.098 | 3.0 | 2011.11 Installation and Operation Guide Bosch Security Systems, Inc.

1Notice

These instructions cover the installation of the Bosch FMR-1000-RCMD Remote Command

Center in a fire system supervised by a Bosch FPA-1000 Analog Addressable Fire Panel or a

Fire Alarm Control Panel with similar connection conditions.

Install, test and maintain the FMR-1000-RCMD according to these instructions, NFPA 72,

Local Codes, and the Authority Having Jurisdiction. Failure to follow these instructions may

result in failure of the device to operate properly. Bosch Security Systems Inc. is not

responsible for improperly installed, tested or maintained devices.

Refer to FPA-1000- Installation and Operation Guide (P/N F.01U.174.607) for detailed wiring

style requirements and complete programming instructions.

2 Scope of Delivery

3 Device Description

The Remote Command Center FMR-1000-RCMD is a four-wire LCD annunciator with system

control capability. It shows the LEDs and LCD display identically to the panel’s and includes a

piezo, scrolling buttons, and operation keys for acknowledge [ACK], drill, reset and silence.

The scrolling functions and the acknowledge [ACK] key are accessible without restriction. The

keys for reset, silence or drill can be enabled and disabled by the device key lock. In addition,

the operation keys or all keys can be locked using DIP switches (refer to Table 7.1 on

Page 11).

The Remote Command Center features tabs with different language versions for LED and key

text. The device allows for surface and semi-flush mounting.

Each FPA-1000 Analog Addressable Fire Panel supports up to a total of eight FMR-1000-RA

Remote Annunciators and/or FMR-1000-RCMD Remote Command Centers.

NOTICE!

NFPA 72 requires a complete system-wide functional test be performed following any

modifications, repair, upgrades, or adjustments made to the system’s components, hardware,

wiring, programming, and software/firmware.

CAUTION!

These instructions contain procedures to follow in order to avoid personal injury and damage

to equipment.

Description

One Remote Command Center (in back box with cover frame)

Tabs with different language versions for LED and key text

One hardware pack

One FMR-1000-RCMD Installation and Operation Guide

Remote Command Center Mounting | en 7

Bosch Security Systems, Inc. Installation and Operation Guide F.01U.078.098 | 3.0 | 2011.11

Figure 3.1 System Overview

4 Mounting

The Remote Command Center should be mounted no higher than shoulder height of the

shortest person operating the system.

4.1 Removing the Cover Frame

4.2 Surface Mounting

1. The back box provides three knockouts for 1/2 in. diameter conduit connectors in the

back, bottom and top side (refer to Figure 4.2, Item 1). To get a clean break, remove the

knockout from the inside of the box.

2. Install the back box with the arrow pointing up (refer to Figure 4.2, Item 2).

3. Use the back box as a template to mark the location of the mounting holes (refer to

Figure 4.2, Item 3). Provide an opening in the mounting surface for the wiring. Pre-start

the screws. Do not secure the screws at this point.

4. The built-in bubble level allows you to level horizontally without extra tools when

securing the base (refer to Figure 4.2, Item 4).

FPA-1000 FMR-1000-RCMD FMR-1000-RA

The device comes with the

mounting material and language

tabs in separate bags. For

removing the device’s cover

frame from the annunciator unit,

hold the assembly and unlock

the snap-fit hooks on one side.

Pull the cover frame off.

Figure 4.1 Removing the Cover Frame (before Installation)

NOTICE!

To get a clean break, remove the knockout from the inside of the box.

8en | Mounting Remote Command Center

F.01U.078.098 | 3.0 | 2011.11 Installation and Operation Guide Bosch Security Systems, Inc.

Before mounting the unit, follow the instructions in

–Section 6 Inserting the Language Tab on Page 10

–Section 7 Address Setting on Page 11

–Section 5 Wiring on Page 9.

Figure 4.2 Back Box of the FMR-1000-RCMD Remote Command Center

4.3 Flush Mounting

Legend

1 Knockout for 1/2 in. conduit connector in the in the back, bottom and top side

2 Arrow pointing up

3 Mounting holes for surface mounting

4 Bubble level

5 Fixing points for annunciator unit (4 screws)

5.5 in. (140 mm)

4.41 in. (112 mm)

7.40 in. (188 mm)

323

1.02 in. (26 mm)

7/8 in. (20 mm)

For flush mounting, use a 3 gang

electrical box. Refer to

Figure 4.3 to select the mounting

holes.

Before mounting the unit, follow

the instructions in

–Section 6 Inserting the

Language Tab on Page 10

–Section 7 Address Setting on

Page 11

–Section 5 Wiring on Page 9.

Figure 4.3 Flush Mounting

Legend

1 Mounting holes for flush mounting

111

3.54 in. (90 mm)

3.19 in. (81 mm)

1.82 in.

(46 mm)

1.82 in.

(46 mm)

Remote Command Center Wiring | en 9

Bosch Security Systems, Inc. Installation and Operation Guide F.01U.078.098 | 3.0 | 2011.11

5 Wiring

5.1 Option Bus Circuit Wiring Distance

Use four conductor, 18 AWG (0.8 mm2) or larger wire to connect Option Bus devices to the

FACP. The total length of wire connected to the Option Bus terminals must not exceed 4000 ft

(1219 m), regardless of the wire gauge used.

The maximum length between any one device and the panel terminals depends on the current

drawn on the branch that the device is on. The current draw on a particular branch can be

found by adding together the individual current draws of each device connected to the

branch. Refer to FPA-1000 Installation and Operation Guide (P/N F.01U.173.607) for detailed

wire length calculations.

5.2 Wiring Connections

The FMR-1000-RCMD is powered by either of the following power outputs from the FPA-1000:

– 12 V DC power (Option bus)

– 24 V FWR unfiltered Aux power output

or UL listed external power supply with common reference ground with the FPA-1000:

– 12 V DC power

– 24 V DC power.

To wire the FMR-1000-RCMD:

1. Power down the control panel.

2. Route the wiring from the FACP to the annunciators.

3. Bring the wiring through one of the knockouts in the annunciator’s base (surface

mounting) or the 3 gang electrical box (flush mounting). Refer to Figure 4.2 on Page 8 for

wire entrance location in the back box.

4. Connect the wiring to the FMR-1000-RCMD terminals. Refer to Figure 5.1.

5. For surface mounting with back box: Secure the base. Use the bubble level to make sure

that the back box is perfectly horizontal. Refer to Figure 4.2 on Page 8.

6. Fasten the annunciator unit with the four mounting screws using a Phillips (cross-

headed) screwdriver. Secure the screw for the earth ground connection. Refer to

7. Place the cover frame onto the base along the top side. Press the bottom part until it

snaps into place.

DANGER!

Explosion and burn hazard. Do not short terminals.

Incorrect connections can result in damage to the unit and personal injury.

Before servicing this equipment, remove all power connections.

Legend

Figure 5.1 Wiring Connections

GND Ground

V+/PWR Power supply

Y Yellow, Data OUT

G Green, Data IN

P3 Power supply

connection

P7 Data connection

YGGND PWR+

10 en | Inserting the Language Tab Remote Command Center

F.01U.078.098 | 3.0 | 2011.11 Installation and Operation Guide Bosch Security Systems, Inc.

Figure 5.2 Position of Mounting Screws and Earth Ground Screw

When the device is powered on, the system performs a selftest. The routine includes checking

of all interfaces, address switches, LEDs, LCD, buzzer, keys, current consumption, and lamp

test.

5.3 Removing the Cover Frame for Service

6 Inserting the Language Tab

For different language versions of LED and key lettering, use the tabs provided with the

FMR-1000-RCMD.

Figure 6.1 Inserting the Language Tab

1. Insert the tab carefully in the slot at the top of the keypad.

2. Slide the tab down carefully until it is completely flush with the keypad.

3. For tab removal, carefully pull upwards at the strap.

For removing the device’s cover

frame when the annunciator unit

is already mounted, insert a

small flathead screwdriver in

each slot at the bottom or at the

top of the frame. Press up and

pull the cover frame off.

Figure 5.3 Removing the Cover Frame (after Installation)

Gas Alarm

Silenced

Power

Trouble

Fire

Supervisory

Gas Alarm

Silenced

Gas Alarm

Silenced

Power

Troubl e

Fire

Supervisory

Gas Alarm

Silenced

Power

Trouble

Fire

Supervisory

Remote Command Center Address Setting | en 11

Bosch Security Systems, Inc. Installation and Operation Guide F.01U.078.098 | 3.0 | 2011.11

7 Address Setting

Each FMR-1000-RCMD connected to the Option Bus of the FPA-1000 must be set to a unique

Option Bus address ranging from 16 to 23. The devices must also be programmed at the

control panel (refer to FPA-1000 Installation and Operation Guide (P/N F.01U.173.607).

The address is set using the DIP switches at the main board of the annunciator unit. Refer to

Table 7.1.

Figure 7.1 Address Setting

Table 7.1 DIP Switch Function

The DIP switch 4 allows for locking the control keys (drill, reset and silence) in OFF position

and for locking all keys in ON position.

The DIP switch 5 enables the device’s key lock in OFF position and bypasses the key lock in

ON position.

8 Programming

All Remote Annunciators and Remote Command Centers have to be configured as elements

connected to the Option Bus.

The FPA-1000 enables various programming approaches:

– On-site at the front panel to program another panel, but not all parameters can be

programmed

– On-site through a Web server using a laptop (connected to the panel with CAT5 cable)

– Remote, using a Web page and a dial-up connection

Option Bus

Address

DIP 1 DIP 2 DIP 3 DIP 4 DIP 5

16 OFF OFF OFF OFF position:

Control keys

are locked.

ON position:

All keys are

locked.

OFF position:

Key lock

active.

ON position:

Key lock

bypassed.

17 ON OFF OFF

18 OFF ON OFF

19 ON ON OFF

20 OFF OFF ON

21 ON OFF ON

22 OFF ON ON

23 ON ON ON

GND PWR+

ON DIP

1 2 3 4 5

ON DIP

1 2 3 4 5

OFF

ON DIP

1 2 3 4 5

OFF

ON DIP

1 2 3 4 5

ON DIP

1 2 3 4 5

OFF

ON DIP

1 2 3 4 5

OFF

ON DIP

1 2 3 4 5

OFF

ON DIP

1 2 3 4 5

ON DIP

1 2 3 4 5

OFF

ON DIP

1 2 3 4 5

OFF

NOTICE!

Each Option Bus device must have its own address, and each address can support only one

device. Ensure that there are no duplicate addresses on the bus.

Inhaltsverzeichnis

Sprachen:

Andere Bosch Fernbedienung Handbücher

Bosch

Bosch ARC R-1 IR Bedienungsanleitung

Bosch

Bosch RG57A6 Bedienungsanleitung

Bosch

Bosch Remote Control Bedienungsanleitung

Bosch

Bosch WRC-HR Bedienungsanleitung

Bosch

Bosch GWH-635-ES Bedienungsanleitung

Bosch

Bosch ASI09DW40 Bedienungsanleitung

Bosch

Bosch FMR-1000-RA Bedienungsanleitung

Bosch

Bosch Remote Control Bedienungsanleitung

Bosch

Bosch CLIMATE 5000 VRF RDCI Series Bedienungsanleitung

Bosch

Bosch CLIMATE 5000 VRF RDCI Series Bedienungsanleitung

Bosch

Bosch BRC3600 Bedienungsanleitung

Bosch

Bosch CR 10H Bedienungsanleitung

Bosch

Bosch Remote Control Bedienungsanleitung

Bosch

Bosch RF3332 Bedienungsanleitung

Bosch

Bosch RADION Series Bedienungsanleitung

Bosch

Bosch 7736504945 Bedienungsanleitung

Bosch

Bosch RC 1 Professional Bedienungsanleitung

Bosch

Bosch 7736504945 Bedienungsanleitung

Bosch

Bosch Climate 5000 Series Bedienungsanleitung

Bosch

Bosch Twist Bedienungsanleitung

Bosch

Bosch WRC-HR Bedienungsanleitung

Bosch

Bosch WRC-HP Bedienungsanleitung

Bosch

Bosch CLIMATE 5000 VRF RDCI Series Bedienungsanleitung

Bosch

Bosch Junkers 1119 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung