Bosch DB18C3100R2 Bedienungsanleitung

DiBos/DiBos Micro

en Installation Guide

DiBos/DiBos Micro Table of Contents | en 3

Bosch Sicherheitssysteme GmbH Installation Guide F.01U.033.308 | V7 | 2009.09

Table of Contents

1SafetyNotes 7

2Introduction 11

2.1 System Description 11

2.2 Unpacking 11

2.3 Power 11

2.4 Environmental 11

2.5 Recommended Virus Scanners/Firewall 12

2.5.1 Virus Scanners 12

2.5.2 Firewall 12

2.6 System Overview/Technical Specifications 14

2.6.1 DiBos 14

2.6.2 DiBos micro 18

3 Device Connections 21

3.1 DiBos 21

3.1.1 DiBos Front View 21

3.1.2 DiBos Rear View 22

3.1.3 Grabber Card for DiBos 23

3.1.4 I/O Card for DiBos 24

3.2 DiBos micro 25

3.2.1 DiBos micro Front View 25

3.2.2 DiBos micro Rear View 26

3.2.3 Grabber Card for DiBos micro 27

3.2.4 I/O Card (for DiBos micro) 28

4 Quick Installation 30

5 Quick Configuration 31

5.1 General Settings 31

5.2 Creating a User 33

5.3 Setting up the Network 34

5.4 Specifying Cameras 36

5.5 Assigning Time Profiles 37

5.6 Setting Up Recording 38

6 Default Configuration 40

6.1 Configuring Drives 40

6.2 Configuring Video and Audio Connections 42

6.2.1 General Camera Settings 44

6.2.2 Setting up Dome Cameras and Pan/Tilt Cameras 46

6.2.3 Specifying Monitoring Zone for Motion Cameras 49

6.2.4 Configuring Tamper Detection 50

6.2.5 Configuring Video Monitors 52

6.2.6 Configuring camera sequence 53

4en | Table of Contents DiBos/DiBos Micro

F.01U.033.308 | V7 | 2009.09 Installation Guide Bosch Sicherheitssysteme GmbH

6.2.7 Editing Audio Settings 54

6.2.8 Configuring JPEG IP Cameras 55

6.2.9 Configuring MPEG4 IP Cameras 58

6.3 Configuring Recording Settings 60

6.3.1 Configuring Recording Settings for Analog Cameras 60

6.3.2 Configuring Recording Settings of JPEG IP Cameras 67

6.3.3 Configuring Recording Settings of MPEG4 IP Cameras 69

6.4 Configuring Time Periods 71

6.5 Configuring Inputs and Outputs 73

6.5.1 Configuring Alarm Inputs 73

6.5.2 Configuring Relay Outputs 74

6.5.3 Configuring Alarm Simulation 75

6.5.4 Configuring Virtual Inputs 76

6.5.5 Configuring Automatic Teller Machines 77

6.5.6 Configuring Foyer Card Readers 79

6.5.7 Configuring AP Inputs 82

6.5.8 Configuring POS Inputs 86

6.5.9 Configuring ATM/POS Inputs 88

6.6 Configuring Alarm Processing 90

6.7 Configuring Remote Stations 94

6.8 Configuring Alarm Transmission 97

6.9 Configuring the Export Video Scheduler 100

6.10 Creating Authorization Levels 102

6.11 Configuring Users 107

6.12 Configuring Error Forwarding 109

6.13 Configuring Options 111

6.13.1 MIB List for SNMP 114

6.13.2 Notification via SNMP 115

6.13.3 Configuring Automatic Alarm Recording 116

6.14 Configuring Browser Access and Network Settings 117

6.15 Administration and Dongle 119

6.15.1 Activating a License 122

7 Remote configuration 123

8XPAdministration 124

8.1 Logging On as a Windows® XP User 124

8.2 Logging On as a Windows® XP Administrator 124

8.3 Changing the Administrator Password 124

9 Connections 125

9.1 Network Connection via DSL 125

9.2 Connecting the ISDN Controller 128

9.3 Connecting VSCom 200 H (Interface Expansion) 129

9.4 Connecting External Hard Disks 129

9.5 Connecting a Malfunction Relay 129

9.6 Connecting an ATM (Serial) 130

9.7 Connecting the MINITER RS 485 Foyer Card Reader 134

9.8 Connecting the DCF 77 Radio Clock 137

DiBos/DiBos Micro Table of Contents | en 5

Bosch Sicherheitssysteme GmbH Installation Guide F.01U.033.308 | V7 | 2009.09

9.9 Connecting a Modem/ISDN Card (for Incoming Connections) 139

9.10 Connecting to AutoDome/SAE Dome 141

9.10.1 Connecting to Bosch Dome Cameras (Directly) 141

9.10.2 Connecting to Bosch Dome Cameras via Matrix Switch 141

9.10.3 Connecting to SAE Dome Cameras (Directly) 142

9.10.4 Connecting to SAE Dome Cameras with V3032 Biphase Interface 142

9.11 Connecting an AP 143

9.11.1 General 143

9.11.2 Connecting to NZ 500 (20 mA) Video System NZ 500 145

9.11.3 Connecting to BZ 500 (20 mA) 145

9.11.4 Connecting to AZ 1010/NZ 1008 146

9.11.5 Connecting to NZ 1012 147

9.11.6 Connecting to NZ 1060 148

9.11.7 Connecting to UEZ 1000 (20 mA) 149

9.11.8 Connecting to UEZ 2000 (20 mA) 149

9.11.9 Connecting to UGM 2020 150

10 Troubleshooting and Checks 151

10.1 Troubleshooting 151

10.2 Checking the Optional Network Connection 152

10.3 Checking the Optional ATM Connection 153

10.4 Checking the Optional Web Connection 154

11 Notes on Service and Maintenance 155

11.1 Maintenance Work to be Carried Out 155

11.2 Software Update 156

11.3 Troubleshooting 156

6en | Table of Contents DiBos/DiBos Micro

F.01U.033.308 | V7 | 2009.09 Installation Guide Bosch Sicherheitssysteme GmbH

DiBos/DiBos Micro Safety Notes | en 7

Bosch Sicherheitssysteme GmbH Installation Guide F.01U.033.308 | V7 | 2009.09

1SafetyNotes

The following safety notes must be observed:

1. Read, follow and retain instructions

All safety and operating instructions must be read and followed before installing the

device. Retain instructions for future reference.

2. Observe warnings

Observe all warnings on the device and in the operating manual.

3. Add-on devices

Do not use add-on devices that are not recommended by the product manufacturer as

these may cause hazards.

4. Installation notes

Do not place the device on an unstable mounting, tripod or similar. The device may fall to

the ground and seriously injure the user or be damaged itself. Only use accessories that

have been recommended by the manufacturer or are delivered with the device. Fit the

device according to the manufacturer's instructions. Exercise extreme caution when

transporting the device on a trolley. Abrupt stopping, extreme force effects and uneven

surfaces may cause the device and the trolley to tip over.

5. Cleaning

Unplug the device from the mains power supply before cleaning. Follow all instructions

for the device. Normally, cleaning can be carried out with a damp cloth. Do not use liquid

cleaners or cleaners in spray cans.

6. Service

Do not attempt to service the device yourself. You may be exposed to high electrical

voltages or other hazards if you open or remove covers. Servicing must be carried out by

qualified maintenance personnel.

7. Damage requiring service.

Unplug the device from the mains power supply and arrange for the device to be serviced

by qualified personnel if:

– The mains cable or mains plug is damaged.

– Liquids or foreign bodies are present in the device.

– The device has come into contact with water and/or has been exposed to extreme

environmental conditions (e.g. rain, snow etc.).

– If the device does not work properly in spite of following the operating instructions,

make changes only to those operating elements that are described in the operating

instructions. Incorrect changes to other operating elements may cause damage

requiring extensive repair work to be carried out by qualified service personnel.

– The device has fallen to the ground or the housing has been damaged.

– A noticeable change in the performance of the device has occurred. In this case, the

device must be serviced.

8. Spare parts

If spare parts are required, service personnel must use spare parts that are

recommended by the manufacturer or correspond to the original parts. Using the wrong

spare parts may result in fire, electric shock or other hazards.

9. Safety test

When servicing or repair is complete, ask service personnel to carry out a safety test to

ensure that the device is working correctly.

8en | Safety Notes DiBos/DiBos Micro

F.01U.033.308 | V7 | 2009.09 Installation Guide Bosch Sicherheitssysteme GmbH

10. Power source

The device must only be operated with the power source indicated on the label. If you are

not sure whether you can operate the device with a specific power source, ask the dealer

from whom you bought the device or your electricity provider.

You will find more information on devices that can be operated with batteries in the

operating manual.

For devices that are operated using external power units, only recommended and tested

power units should be used.

For devices that are operated using power units with limited power, the power unit must

conform to the EN 60950 standard. Other replacement power units may damage the

device and lead to fire or electric shock.

For devices that are operated using 24 V AC, the normal input voltage is 24 V AC. The

input voltage to the device should not exceed 30 V AC. The wiring provided by the

customer for connecting the power source to the device (24 V AC) must conform to

electrical codes (Class 2 power stages). The power source (24 V AC) must not be

grounded at the connectors or the power supply connections on the device.

11. Coax grounding

If a cable system is connected to the device for outside use, ensure that the cable system

is grounded. Only for models available in the USA: Section 810 of the National Electrical

Code, ANSI/ NFPA No.70-1981, contains information on the correct grounding of the

mounting, coax grounding at a discharge device, the size of the ground conductors, the

location of the discharge device, connection to discharge electrodes and requirements

regarding the discharge electrodes.

12. Grounding or polarizing

This device may have a polarized AC plug (a plug with one pin broader than the other).

With this protection system, the plug can only be inserted into a socket in one way. If you

are unable to insert the plug fully into the socket, rotate it and try again. If you are still

unable to insert the plug, ask an electrician to replace the socket with a later model. Do

not attempt to bypass the polarized plug.

Alternatively, the device may have a 3-phase ground plug with a third (grounding) pin.

With this protection system, the plug can only be inserted into a grounded socket. If you

are unable to insert the plug into the socket, ask an electrician to replace the socket with

a later model. Do not attempt to bypass the grounded plug.

13. Lightning

For added protection of the device during a storm, or when it is not used for a lengthy

period of time, unplug the device from the mains and disconnect the cable system. This

prevents the device being damaged by lightning or a power surge.

14. The installation location should be quiet and have only limited access.

DiBos/DiBos Micro Safety Notes | en 9

Bosch Sicherheitssysteme GmbH Installation Guide F.01U.033.308 | V7 | 2009.09

Devices for inside use

Water and damp — Do not use this device in the vicinity of water (e.g. in a damp cellar) or in

humid locations.

Entry of foreign bodies and liquids — Do not insert foreign bodies into the device openings

as you may touch parts that are at high-voltage or cause a short circuit, which may result in

fire or electric shock. Do not spill liquids on the device.

Mains cable and mains cable protectors — For devices that operate at 230 V AC, 50 Hz, the

input and output mains cables must conform to IEC publication 227 or IEC publication 245.

Mains cables should be laid in such a way that no one can step on them and no other objects

can be placed on top of them or leant against them. Particularly protect cables, plugs and

sockets as well as device entry points.

Overloading — Do not overload sockets and extension cables as this may result in fire or

electric shock.

Rack-mounting devices

Ventilation — This device should not be installed anywhere where correct ventilation cannot

be ensured or the manufacturer's instructions cannot be followed. The maximum operating

temperature for this device must not be exceeded.

Mechanical load — When installing the device in a rack, beware of hazards that may arise due

to unequal mechanical load.

WARNING!

Interruption of mains supply:

Voltage is applied as soon as the mains plug is inserted into the mains socket.

However, for devices with a mains switch, the device is only ready for operation when the

mains switch (ON/OFF) is in the ON position. When the mains plug is pulled out of the socket,

the supply of power to the device is completely interrupted.

WARNING!

Removing the housing:

To avoid electric shock, the housing must only be removed by qualified service personnel.

Before removing the housing, the plug must always be removed from the mains socket and

remain disconnected while the housing is removed. Servicing must only be carried out by

qualified service personnel. The user must not carry out any repairs.

WARNING!

Lithium battery:

Batteries that have been inserted wrongly can cause an explosion. Always replace empty

batteries with batteries of the same type or a similar type recommended by the manufacturer.

Dispose of empty batteries according to the manufacturer's instructions.

CAUTION!

Electrostatically sensitive device:

To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried

out correctly.

When handling electrostatically sensitive printed circuits, grounded anti-static wrist bands

must be worn and the ESD safety precautions observed.

10 en | Safety Notes DiBos/DiBos Micro

F.01U.033.308 | V7 | 2009.09 Installation Guide Bosch Sicherheitssysteme GmbH

NOTICE!

Installation should only be carried out by qualified customer service personnel in accordance

with the applicable electrical regulations.

Disposal

Your Bosch product has been developed and manufactured using high-quality materials and

components that can be reused.

This symbol means that electronic and electrical devices that have reached the end of their

working life must be disposed of separately from household waste.

In the EU, separate collecting systems are already in place for used electrical and electronic

products. Please dispose of these devices at your local communal waste collection point or at

a recycling center.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bosch Sicherheitssystem Handbücher

Bosch

Bosch CP156B Anleitung zur Verwendung

Bosch

Bosch Security System Bedienungsanleitung

Bosch

Bosch MIC-9502 Bedienungsanleitung

Bosch

Bosch DIP-2040-00N Bedienungsanleitung

Bosch

Bosch Solution 16i Bedienungsanleitung

Bosch

Bosch LTC 9441 Series Bedienungsanleitung

Bosch

Bosch PRAESENSA Bedienungsanleitung

Bosch

Bosch Fire System Bedienungsanleitung

Bosch

Bosch DIP-2040-00N Bedienungsanleitung

Bosch

Bosch ISW-BMC1-M82X Anleitung zur Verwendung

Bosch

Bosch D623 Series Bedienungsanleitung

Bosch

Bosch Praesideo Bedienungsanleitung

Bosch

Bosch SE 60 LSNi Bedienungsanleitung

Bosch

Bosch SM120RW Bedienungsanleitung

Bosch

Bosch SE 320 LSNi Bedienungsanleitung

Bosch

Bosch Security Escort SE2000 Series Installationsanleitung

Bosch

Bosch FMM-100 Series Bedienungsanleitung

Bosch

Bosch MAP 5000 Series Bedienungsanleitung

Bosch

Bosch ICP-VR8488 Bedienungsanleitung

Bosch

Bosch OD850F1 Bedienungs- und Wartungshandbuch

Bosch

Bosch RF1100E Bedienungsanleitung

Bosch

Bosch PAVIRO Montageanleitung

Bosch

Bosch PR111B Bedienungsanleitung

Bosch

Bosch Dinion LTC 0385 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung