Bosch TC2073 Bedienungsanleitung
Instruction Manual
EN Indoor Wall and
Corner Housings
TC2073
EN |2
Bosch Security Systems | 09 August 2004
TC2073 | Instruction Manual | Important Safeguards
Important Safeguards
1. Read, Follow, and Retain Instructions - All safety
and operating instructions should be read and
followed before operating the unit. Retain instructions
for future reference.
2. Heed Warnings - Adhere to all warnings on the unit
and in the operating instructions.
3. Electrical Connections - Only a qualified electrician
should make electrical connections.
4. Cable Runs - All cable runs must be within
permissible distances.
5. Mounting - This unit must be properly and securely
mounted to a supporting structure capable of
sustaining the weight of the unit. Accordingly:
a. The installation should be made by a qualified
installer, in compliance with local codes.
b.Exercise care in selecting suitable hardware to
install the unit, taking into account both the
composition of the mounting surface and the
weight of the unit. Periodically examine the unit
and the supporting structure to ensure that the
integrity of the installation is intact.
Failure to comply with these stipulations may result in
separation from the support structure. This may cause
damages or injury to anyone or anything struck by the
falling unit.
6. Attachments - Attachments not recommended by
the product manufacturer should not be used, as they
may cause hazards.
Safety Precautions
Attention: Installation should be performed by
qualified service personnel only in accordance
with the National Electrical Code or applicable
local codes.
Power Disconnect. Units with or without
ON-OFF switches have power supplied to the
unit whenever the power cord is inserted into the
power source; however, the unit is operational
only when the ON-OFF switch is in the ON
position. The power cord is the main power
disconnect for all units.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol indicates the presence of
uninsulated “dangerous voltage” within the
product’s enclosure. This may constitute a
risk of electric shock.
The user should consult the operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
EN |3
Bosch Security Systems | 09 August 2004
TC2073 Series | Instruction Manual | Unpacking
1UNPACKING
This mechanical equipment should be unpacked and
handled carefully.
Check for the following items:
Qty. Item
1Model No. of unit
1Key (taped to the housing cover)
1Corner-mount housing
1Camera bracket
1Toolhead driver1for security fastener
1One tool per housing
If an item appears to have been damaged in shipment,
replace it properly in its carton and notify the shipper.
If any items are missing, notify your Bosch Security
Systems Inc. Sales Representative or Customer Service.
The shipping carton is the safest container in which the
unit may be transported. Save it for possible future use.
2SERVICE
If the unit ever needs repair service, the customer
should contact the nearest Bosch Security Systems, Inc.
Service Center for return authorization and shipping
instructions.
Service Centers
USA
Phone: 800-366-2283 or 717-735-6638
fax: 800-366-1329 or 717-735-6639
CCTV Spare Parts
Phone: 800-894-5215 or 408-956-3853 or 3854
fax: 408-957-3198
e-mail: [email protected].com
Canada
Phone: 514-738-2434
Europe, Middle East & Asia Pacific Region
Phone: 32-1-440-0711
For additional information, see
www.boschsecuritysystems.com.
3INSTALLATION
1. Remove the contents from the box.
2. Loosen the security fasteners using the toolhead
driver, and open the front half of the housing.
3. Remove the paper from the back side of the
window.
4. The Camera bracket can be mounted into the
housing in one of two ways, depending on camera
size and the desired angle (see FIGURE 1).
5. Place the housing in the corner and mark the
location of the four (4) mounting holes.
6. Pass the electrical and video cables through the
hole provided in the back of the housing.
7. Mount the housing by bolting it to the wall.
8. Make the electrical and camera connections.
USE 0NLY CLASS 2 POWER SUPPLY FOR
THE CAMERA.
9. Adjust the camera angle and tighten the camera
bracket. Loosen, but do not remove the nuts to
adjust the bracket.
10. Close the housing and tighten the security
fasteners.
FIGURE 1
© 2004 Bosch Security Systems GmbH
3935 890 15912 04-33 | Updated August 09, 2004 | Data subject to change without notice.
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601 USA
Tel: 800-326-3270
Fax: 1-717-735-6560
www.boschsecuritysystems.com
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven
The Netherlands
Tele +31 40 27 80000
Bosch Security Systems Pte Ltd.
38C Jalan Pemimpin
Singapore 577180
Republic of Singapore
Tel: 65 (6) 319 3486
Inhaltsverzeichnis
Andere Bosch Sicherheitssystem Handbücher
Bosch
Bosch FMM-100 Series Bedienungsanleitung
Bosch
Bosch BIS 2.3 Bedienungsanleitung
Bosch
Bosch PAVIRO Montageanleitung
Bosch
Bosch AMAX panel 2100 Bedienungsanleitung
Bosch
Bosch MIC-WKT-IR Bedienungsanleitung
Bosch
Bosch PRAESENSA Bedienungsanleitung
Bosch
Bosch Solution 64 Bedienungsanleitung
Bosch
Bosch MAP 5000 Bedienungsanleitung
Bosch
Bosch LTC 8016/90 Bedienungsanleitung
Bosch
Bosch DS484Q Bedienungsanleitung
Bosch
Bosch LTC 5136/61 Bedienungsanleitung
Bosch
Bosch 2212 Bedienungsanleitung
Bosch
Bosch Solution 2000 Betriebsanleitung
Bosch
Bosch FW5.50 Montageanleitung
Bosch
Bosch Plena Power Amplifier Montageanleitung
Bosch
Bosch CM728B Anleitung zur Verwendung
Bosch
Bosch Dinion LTC 0385 Bedienungsanleitung
Bosch
Bosch AVENAR all-in-one 4000 Bedienungsanleitung
Bosch
Bosch FRP-OW3000 Bedienungsanleitung
Bosch
Bosch D222 Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung