Bosch Fireray3000 Bedienungsanleitung
Fire Alarm Systems | Fireray3000
Fireray3000
www.boschsecurity.com
uMonitoring range of 5m to 120m (max. 100m
according to DIN VDE 0833-2)
uUp to 2 detectors per system controller
uTwo pairs of fire and fault relays (one per detector)
uTransmitter and receiver integrated into a compact
housing
uIntegral LASER alignment
The Fireray3000 is an optical Linear Smoke Detector
for the detection of light and dark smoke across an
area of 5 m to 120 m (max. 100m according to DIN
VDE 0833-2)
Preferred areas of application are very large and high
halls, e. g. airplane hangars, factory buildings and
similar buildings where the use of point detectors are
not possible.
Functions
The transmitter transmits an invisible infrared light
beam bundled through a lens to the receiver.
S3m
30m 50m 80m 100m
0,9m 1,5m 2,4m
Beam detection
At a maximum distance of 100 m (According to DIN
VDE 0833-2) the core diameter of the light beam is
3 m. The core diameter is the area of the conical IR
beam in which orderly operation of the system is
possible.
If smoke interrupts the beam, the signal in the receiver
is attenuated depending on the thickness of the
smoke. If an attenuation according to the set threshold
lasts longer than 5 s, an alarm is triggered.
The alarm threshold can be set to 25% or 35% or 50%
with the use of prisms.
Slow changes (e. g. contamination of the optical
system) do not cause false alarms; instead, they are
balanced out by an automatic gain control. Here the
current state of the system is compared with a
reference value and adjusted stepwise in case of
deviations greater than 7%. By default, the comparison
is done every 1.5 hours.
With a comp switch, manual or automatic alarm reset
can be selected.
Certifications and approvals
Region Certification
Germany VdS Fireray3000
Europe CE Fireray3000
CPD 0786-CPD-21162 Fireray3000
USA UL UROX.S3417 Fireray3000
UL UROXC.S3417 Fireray3000
CSFM 7260-1508:0105 Fireray3000
Installation/configuration notes
General installation/configuration notes
• A FLM‑420/4‑CON Conventional Interface Module is
required for connection of the Fireray3000 to the
LSN.
• Between the transmitter and receiver there must be a
constant visual connection, which may not be
interrupted by movable objects (e. g. overhead
crane).
• The mounting surfaces for the transmitter and
receiver must be stable and free of vibration.
Installation on metal surfaces should be avoided since
they expand and contract in case of temperature
fluctuations.
• Inaccessible areas are monitored by monitoring
transmitters and receivers outside and letting them
look through windows into the monitoring area. The
minimum diameter of the opening must be 20 cm or
an opening corresponding to the diameter of the
beam.
Notice
Normal panes of glass reduce the effective system
range by approx. 10% per pane
• When installing the receiver, be sure that the direct
penetration of sunlight or other light into the optical
system is avoided. Normal environmental light has no
influence on the receiver.
• The control unit must be installed in an area that is
easy to reach. A screened cable must be used. The
maximum cable length of 100 m to the receiver may
not be exceeded.
Heat accumulation under roof surfaces can prevent the
travel of climbing smoke to the ceiling. The detector
must therefore be mounted below an expected heat
accumulation. This can mean that the benchmark
values for DL specified in the table must be exceeded.
30-60 cm C
B
A
D
installation_for_smoke_plume
Pos. Description
ACeiling
B Mushroom cloud
C Heat accumulation
D IR beam
• Since the smoke from a fire does not simply rise
straight up, but rather spreads like a mushroom cloud
(depending on air current and accumulation), the
monitoring range is much greater than the diameter
of the IR beam.
• The lateral detection on either side of the beam is
7.5 m.
• Country-specific Standards and guidelines on
planning must be observed.
Detector arrangement
The detectors must be arranged according to the
following distances:
X1 Distance from the ceiling 0.3 m to 0.6 m
X2 Horizontal distance detector/wall min. 0.5 m
X3 Horizontal distance between two
detectors under gable roofs
Example: Gable roof, 10° roof pitch
X3 = 7.5 m + (7.5 m x 10%)
X3 = 7.5 m + 0.75 m
X3 = 8.25 m
• The maximum distance between two detectors with
parallel IR beams is 15 m.
• The centre line of the monitoring beam may not be
closer than 0.5 m to walls, furniture or stored goods.
• The receivers allow an angle deviation of up to 5°
from the centre line without causing a weakening of
the signal.
Positioning the detectors on flat ceilings
15m
7.5m 7.5m
0.3m < X1 < 0.6m
X1
X2
0.5m < X2 < 7.5m
15m 15m
Mounting flat ceiling
Positioning the detectors under a shed roof
X1
X2
10°
0.3 m < X1 < 0.6 m
X3
X3
0.5 m < X2 < 7.5 m
X2
Mounting shed roof
2 | Fireray3000
Positioning the detectors under a gable roof
0.5m X2
X1
X1
X1
X1
15m 15m
0.5m < X2 < 7.5m
Φ
Mounting gable roof
Detector arrangement in accordance with VdS/VDE
• The number of light beam smoke detectors must be
selected according to the maximum monitoring area A
listed in the table and which must not be exceeded
(meets VdS 2095 and DIN VDE 0833‑2).
Room height RH X2 A X1 at
α< 20°
X1 at
α> 20°
Up to6 m 6 m 1200 m2 0.3 m to
0.5 m
0.3 m to
0.5 m
6 m to 12 m 6,5 m 1300 m2 0.4 m to
0.7 m
0.4 m to
0.9 m
12 m to
16 m *)**)
7 m*)) 1400 m2**) 0.6 m to
0.9 m**)
0.8 m to
1.2 m**)
X2 = greatest permissible horizontal distance of any
point of the ceiling to the next-closest beam
A = maximum monitoring area per detector (= double
the product of the greatest horizontal distance DH and
the highest allowable distance between transmitter
and receiver)
X1 = distance between the detector and the ceiling
α = angle which the roof/ceiling pitch forms with the
horizontal; if a roof has different pitches (e. g. sheds),
use the smallest pitch.
* With a room height of more than 12 m, it is
recommended that you provide a second monitoring
level on which the detectors are arranged offset to the
first monitoring level
** Depends on use and environmental conditions (e. g.
quick fire and spread of smoke)
• Depending on the roof construction (flat, tilted or
gable), the detectors and receiver must be arranged
according to the roof pitch α and the room height RH
so that the light beam runs along the roof in a
distance DL (see table).
Parts included
Qty. Components
1Control Unit, Fireray3000 Linear Smoke Detector
1 Infrared transmitter
1 Infrared receiver
Technical specifications
Electrical
Operating voltage 12 V DC to 36 V DC (±10%)
Current consumption
• Control Unit in standby (with 1
or 2 receivers)
14 mA @ 36 V DC
• Transmitter in standby 8 mA @ 36 V DC
Reset control by power disruption > 20 s
Fire and fault relay (contact load) Resistive VFCO 2 A @ 30 V
Mechanics
LED indicators:
• Control Unit Red = Fire
Amber = Fault
Green = System OK
• Receiver Red = Fire
Alignment LEDs for single person
alignment
Dimensions (W x H x D)
• Transmitter & Receiver 78 x 77 x 161 mm
• Control unit 203 x 124 x 72 mm
Housing
• Color Light gray/black
• Material C6600, non-flammable
Weight
• Detector 500 g
• Prism reflector 100 g
• Control unit 1000 g
Environmental conditions
Protection class as per EN 60529 IP 54
Permissible operating
temperature
-10 °C to 55°C
Planning
Permissible distance transmitter-
receiver
Min. 5 m – max. 100 m
Connectable detectors per
system controller
2 Transmitter and 2 Receiver
Special features
Optical wavelength 850 nm
3 | Fireray3000
Ordering information
Fireray3000
End-to-End Linear Smoke Detector for ranges between
5 m - 120 m (max. 100m according to DIN VDE 0833-2)
Order number Fireray3000
Accessories
Fireray3000-HD
Additional detector head
Order number Fireray3000-HD
4 | Fireray3000
Represented by:
Americas: Europe, Middle East, Africa: Asia-Pacific: China: America Latina:
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
www.boschsecurity.us
Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
www.boschsecurity.com
Robert Bosch (SEA) Pte Ltd, Security
Systems
11 Bishan Street 21
Singapore 573943
Phone: +65 6571 2808
Fax: +65 6571 2699
www.boschsecurity.asia
Bosch (Shanghai) Security Systems Ltd.
201 Building, No. 333 Fuquan Road
North IBP
Changning District, Shanghai
200335 China
Phone +86 21 22181111
Fax: +86 21 22182398
www.boschsecurity.com.cn
Robert Bosch Ltda Security Systems Division
Via Anhanguera, Km 98
CEP 13065-900
Campinas, Sao Paulo, Brazil
Phone: +55 19 2103 2860
Fax: +55 19 2103 2862
www.boschsecurity.com
© Bosch Security Systems 2013 | Data subject to change without notice
12949575563 | en, V1, 04. Dec 2013
Inhaltsverzeichnis
Andere Bosch Rauchmelder Handbücher
Bosch
Bosch RFSM-A Bedienungsanleitung
Bosch
Bosch D296/D297 Benutzerhandbuch
Bosch
Bosch FRP-OW3000 Bedienungsanleitung
Bosch
Bosch FAP-520 Bedienungsanleitung
Bosch
Bosch EVAX25E Produktinformationsblatt
Bosch
Bosch AVENAR 4000 FAP-425-O Bedienungsanleitung
Bosch
Bosch FAS-420-TT Series Bedienungsanleitung
Bosch
Bosch FCS-320-TP2 Installationshandbuch
Bosch
Bosch Titanus Pro?Sens TP-1 A Bedienungsanleitung
Bosch
Bosch FERION 1000 O Bedienungsanleitung
Bosch
Bosch FAS-420-TM-R Bedienungsanleitung
Bosch
Bosch D326A Anwendungshandbuch
Bosch
Bosch ISW-BSM1-SX Bedienungsanleitung
Bosch
Bosch FERION 1000 O Bedienungsanleitung
Bosch
Bosch D341 Bedienungsanleitung
Bosch
Bosch FMM‑100SAT2CKEX Bedienungsanleitung
Bosch
Bosch FAS-420-TM Bedienungsanleitung
Bosch
Bosch FERION 4000 O Bedienungsanleitung
Bosch
Bosch FCP-320 Series Bedienungsanleitung
Bosch
Bosch D296 Series Bedienungsanleitung
Beliebte Rauchmelder Handbücher anderer Marken
System Sensor
System Sensor DH500ACDC Bedienungsanleitung
Resolution Products
Resolution Products RE612 CryptiX Bedienungsanleitung
First Alert
First Alert PC900V Bedienungsanleitung
Eminent
Eminent EM6590 E-Domotica Bedienungsanleitung
Ei Electronics
Ei Electronics Ei Ei168RC Bedienungsanleitung
Carrier
Carrier Kidde Quell Q301 Bedienungsanleitung
