BOSSCO TPSE201 Bedienungsanleitung
1
Instruction Manual
TPSE201 (181422) - BOSSTM Universal Programmer
TPSE101 (569565) - BOSSTM Universal Timeswitch
Thank you for purchasing this product. If installing for someone else, please ensure that the
instructions are handed to the householder.
Please read this manual prior to installation or use. Retain for future reference.
Always isolate the mains supply before removing the unit from the backplate.
Please leave these instructions with the end user where they should be kept in a safe place for
future reference
Installation
The TPSE201/TPSE101 is easily installed using the backplate supplied. This can be mounted directly to
the wall or a single gang recessed box using the holes provided; cable entry is from the rear.
Specification
Power supply 230V/50Hz
Switch rating 6(2)A
Switch type Single pole, double throw (SPDT)
Operating temperature 0°C - 50°C
Storage conditions -20°C - 60°C
Frost protection temperature 5°C
Programme 5/2, 7 day or daily selectable by jumper
3 setting per day
Time display 12 or 24 hour
Memory Internal memory back-up
Backlight Green LED
Switches/Jumpers
The installer should select the jumper positions required if changing from the factory pre-sets, these
jumpers are found on the rear of the unit. Always enable the internal memory back up battery before
installing the unit,
Switch/Jumpers Function
Program type 3x2 pins jumpers for 5+2 days (factory default setting),
7 days program or daily
P/G (TPSE201 only) 3x1 pin jumper for fully pumped and controlled system
(factory default setting) or gravity-fed hot water system.
Internal backup battery 3x1 pin jumper to enable/disable the internal backup
battery (disabled is the factory default setting)
2
BackPlate & Wiring
This unit does not require an earth connection. The earth terminal is provided for safe retention of
circuit earth wires only.
1. Select a suitable location noting the advice in page 1 of this manual, a suitable mounting height is
1.5m above the floor
2. Isolate the AC mains supply, note this must be 230Vac and fused at 6 Amps.
3. Optimum cable size is 1.5mm2
Check the system wiring specification to confirm connections and cable core colour identification.
4. Cable must enter from the rear of the backplate.
5. Securely fix the backplate directly to the wall or fit to a recessed back box.
6. Terminate cables in accordance with the wiring diagram on the unit, ensuring conductors are
firmly gripped between the square brass washers.
7. This appliance is double insulated and must not be earthed. The earth terminal is provided for
safe retention of circuit earth wires only.
8. The backplate has 6 holes through which to fix to the surface of your choice. Please note that
when fitting the controller to the backplate, some pressure downwards is required to lock the
pins in the unit to the connectors in the backplate. Secure the controller to the backplate with the
captive screws at the bottom taking care not to over tighten.
9. Enable the memory back up.
10. Restore mains to system when all the associated items are fully installed and test for correct
operation.
NOTE: mains power is required to programme unit.
Please note: Always isolate the mains power prior to fitting the unit onto the backplate and when
the backplate is exposed.
Terminals:
TPSE101
Terminal Name Function
N Neutral
L Live
2 Common (ex-factory with jumper to L)
3 (CH OFF) Central Heating OFF
4 (CH ON) Central Heating ON
E Earth
Remark: For volt free setting, remove jumper between L & 2.
TPSE201
Terminal Name Function
N Neutral
L Live
1 (HW OFF) Hot Water OFF
2 (CH OFF) Central Heating OFF
3 (HW ON) Hot Water ON
4 (CH ON) Central Heating ON
E Earth
3
Internal Wiring
Wiring diagrams (TPSE201)
Alternative wiring connections for other BOSSTM room thermostats
* Wireless thermostat receiver unit MUST have permanent mains power from fused spur to operate correctly.
4
Wiring diagrams (TPSE101)
Note: Wireless thermostat receiver unit MUST have permanent mains power from fused spur to operate correctly.
User Instructions
Keyboard
Key Function
Mode (CH) Operating mode selection for Central Heating
Hr+ (CH) Temporary override for Central Heating
Adv (CH) Advance to next program for Central Heating
Mode (HW) Only for TPSE201 Operating mode selection for Hot Water
Hr+ (HW) Only for TPSE201 Temporary override for Hot Water
Adv (HW) Only for TPSE201 Advance to next program for Hot Water
Increase set Temperature.
Decrease set Temperature.
Turn on backlight for 10 seconds. Activate/de-activate holiday override.
Set Press to begin/confirm programming settings.
Select Press to select day(s)/time/temperature.
5
Initial Power Up
• After power up or Reset is pressed, all programmes are reset.
• During system reset, all LCD segments are turned on for 2 seconds. After 2 seconds, the
programmer is initialized and the display will look like this.
Setting of the TPSE201/TPSE101 after reset
Function Status after Reset
Operation Mode Auto mode
12/24 hour 24h
Clock 12:00
AM/PM indicator N/A
Date 2016-Jan-1
Daylight Saving On
Program Default factory setting
Program Number indicator Depends on program
SET indicator Off
PROG indicator Off
Mode indicator(s) “Auto”
CH/HW indicator(s) Depends on program
Output Relay Depends on program
• After reset, the TPSE201/TPSE101 will operate in Auto mode.
Default Program Settings after reset
Same for both 5-2 and 7 days programmes.
Program Output CH HW
Day of week (Mon to Sun) Day of week (Mon to Sun)
1On 06:00 06:00
Off 08:00 08:00
2On 10:00 10:00
Off 12:00 12:00
3On 18:00 18:00
Off 22:00 22:00
6
Setting the Clock
• Press and hold Set and Select in Normal mode for 3 seconds to enter Clock setting mode.
“12 hr” or “24 hr”, and “SET” are displayed. All other indicators are cleared.
• Release Set and Select, press or to toggle between “12 hr” or “24 hr” format.
• Press Select, clock and “SET” are displayed. “Hour” is flashing to indicate that it is the selected
item to be adjusted.
• Release Select, press or to increase or decrease the “hour” respectively.
• Press and release Select, press or to increase or decrease the “minute” respectively.
• Press and release Select to set the Year, “y xx” is displayed, press or to increase or decrease
the “year” respectively. The “year” can set between 20”16” and 20”99” inclusive.
• Press and release Select to set the Month of Year, “m xx” is displayed, press or to increase
or decrease the “month” respectively. The “month” can set between “01” to “12”.
• Press and release Select to set the Day of Month, “d xx” is displayed, press or to increase or
decrease the “day” respectively. The “day” can set between “01” to the end of the month which
is determined by the year and month set above.
7
• Press and release Select to set Day Light Saving, “dLS xx” is displayed, press or to enable or
disable the Day Light Saving.
• Press and release Select to allow change of “hour” again, but not the 12/24 hour format.
• Press and hold or for 2 seconds to advance the value quickly without repeated presses.
• Selected item will stop flashing when a key is pressed. The selected item will flash again once the
key is released.
• Press Set at any time to confirm the setting and return to normal mode.
• TPSE201 / TPSE101 will return to normal mode after 10 seconds if no key is pressed, the clock is
also updated with the latest setting.
Day Light Saving
When enabled, the clock will automatically shift 1 hour ahead of the current set time from the last
Sunday in March at 2:00am until the last Sunday in October at 2:00am.
5-2, 7 days or daily program
• Programmed events must happen in chronological order i.e., the OFF time cannot be earlier than
the ON time and the time of program 3 cannot be earlier than that of program 2 etc.
• Each time can be set between 3.00 am and 2.50 am (on the next day) to allow you to
programme the CH/HW to stay on past midnight, if required.
• The PROG display indicates the program number.
• The CH/HW display indicates whether CH or HW is being programmed. No CH/HW indicator is
displayed in TPSE101.
• The selected item will be flashing and can be adjusted by or key. Program time is changed in
1 minute steps.
• Press and hold or for 2 seconds to advance the value quickly without repeated presses.
• Selected item will stop flashing when a key is pressed. The selected item will flash again once the
key is released.
• The unit will return to normal mode after 10 seconds if no key pressed, Program settings are
stored.
• Program review/changes are allowed even when Temporary Override or Adv Mode is enabled.
5-2 days program selected
• Central Heating and Hot Water have independent programmes set. 3 different time settings
can be programmed for weekdays or weekend. Total 6 settings for TPSE101, and 12 settings for
TPSE201.
• To review or change program, press Set in normal mode to enter programming mode.
The weekday and “SET PROG” are displayed, all other indicators are cleared. The weekdays are
flashing to indicate that it is the selected item to be adjusted.
8
• Press or to select the program set for Weekday/Weekend/CH/HW to be reviewed or
adjusted in the sequences below.
TPSE101: Weekday CH -> Weekend CH -> Weekday CH -> …
TPSE201: Weekday CH -> Weekend CH -> Weekday HW -> Weekend HW -> Weekday CH -> …
• Press Set at any time to confirm the setting and return to normal mode.
• Press Select at any time to confirm the selection. The hour is flashing to indicate that it is the
selected item to be adjusted.
• Press Select to step through the items to be reviewed or adjusted in the sequences below.
(Program 1 ON) “hour” ➝ “minute” ➝
(Program 1 OFF) “hour” ➝ “minute” ➝
(Program 2 ON) “hour” ➝ “minute” ➝
(Program 2 OFF) “hour” ➝ “minute” ➝
(Program 3 ON) “hour” ➝ “minute” ➝
(Program 3 OFF) “hour” ➝ “minute” ➝
and then cycle back to (Program 1 ON)
• Press Set at any time to confirm the setting and return for program set selection.
7 days program selected
• Central Heating and Hot Water have independent programmes set. 3 different time settings
can be programmed for each day of week. Total 21 settings for TPSE101 and 42 settings
for TPSE201.
• To review or change a program, press Set in Normal mode to enter programming mode.
The Monday and “SET PROG” are displayed. All other indicators are cleared. The day of the
week is flashing to indicate that it is the selected item to be adjusted.
9
• Press or to select the program set for Day of Week to be reviewed or adjusted in the
sequences below.
Monday CH <-> Monday HW <-> Tuesday CH <-> ... <-> Sunday HW -> Monday CH
• Press Set at any time to confirm the setting and return to normal mode.
• Press Select at any time to confirm the selection. The hour is flashing to indicate that it is the
selected item to be adjusted.
• Press Select to step through the items to be reviewed or adjusted in the sequences below.
(Program 1 ON) “hour” ➝ “minute” ➝
(Program 1 OFF) “hour” ➝ “minute” ➝
(Program 2 ON) “hour” ➝ “minute” ➝
(Program 2 OFF) “hour” ➝ “minute” ➝
(Program 3 ON) “hour” ➝ “minute” ➝
(Program 3 OFF) “hour” ➝ “minute” ➝
and then cycle back to (Program 1 ON)
• Press Set at any time to confirm the setting and return to program selection.
Daily program selected
• Central Heating and Hot Water have independent programmes. 3 different time settings can
be programmed for all days. Total 3 settings for TPSE101 and 3 settings for TPSE201.
• To review or change a setting, press Set in Normal mode to begin programming. The all
day and “SET PROG” are displayed. All other indicators are cleared. All days are flashing to
indicate that it is the selected item to be adjusted.
10
• Press or to select the program set for Weekday/Weekend/CH/HW to be reviewed or
adjusted in the sequence below.
Weekday CH -> Weekday HW -> Weekend CH -> Weekend HW -> Weekday CH
• Press Set at any time to confirm the setting and return to normal mode.
• Press Select at any time to confirm the selection. The hour will be flashing to indicate that it
is the selected item to be adjusted.
• Press Select to select among the items to be reviewed or adjusted in the sequences below:
(Program 1 ON) “hour” ➝ “minute” ➝
(Program 1 OFF) “hour” ➝ “minute” ➝
(Program 2 ON) “hour” ➝ “minute” ➝
(Program 2 OFF) “hour” ➝ “minute” ➝
(Program 3 ON) “hour” ➝ “minute” ➝
(Program 3 OFF) “hour” ➝ “minute” ➝
and then cycle back to (Program 1 ON)
• Press Set at any time to confirm the setting and return to program selection.
Operating Mode Selection:
• In normal operating mode, press Mode to step through the four operating modes: On, Once,
Auto, and Off.
• For each press and release of Mode, the operating mode is cycled in the following sequence:
On ➝ Once ➝ Auto ➝ Off ➝ On
• The mode indicator is changed to indicate the selected mode.
Dieses Handbuch passt für folgende Modelle
1
